Datasheet

RL78/G13 3. ELECTRICAL SPECIFICATIONS (G: TA = -40 to +105C)
Page 123 of 194
R01DS0131EJ0310 Rev.3.10
Nov 15, 2013
3. ELECTRICAL SPECIFICATIONS (G: TA = -40 to +105C)
This chapter describes the electrical specifications for the products "G: Industrial applications (T
A = -40
to +105C)".
Cautions 1. The RL78 microcontrollers have an on-chip debug function, which is provided for
development and evaluation. Do not use the on-chip debug function in products
designated for mass production, because the guaranteed number of rewritable times of the
flash memory may be exceeded when this function is used, and product reliability therefore
cannot be guaranteed. Renesas Electronics is not liable for problems occurring when the
on-chip debug function is used.
2. With products not provided with an EV
DD0, EVDD1, EVSS0, or EVSS1 pin, replace EVDD0 and EVDD1
with V
DD, or replace EVSS0 and EVSS1 with VSS.
3. The pins mounted depend on the product. Refer to 2.1 Port Function to 2.2.1 With
functions for each product
in the RL78/G13 User’s Manual Hardware .
4. Please contact Renesas Electronics sales office for derating of operation under T
A = +85C
to +105C. Derating is the systematic reduction of load for the sake of improved reliability.
There are following differences between the products "G: Industrial applications (TA = -40 to +105C)" and the
products “A: Consumer applications, and D: Industrial applications”.
Application Parameter
A: Consumer applications,
D: Industrial applications
G: Industrial applications
Operating ambient temperature TA = -40 to +85C TA = -40 to +105C
Operating mode
Operating voltage range
HS (high-speed main) mode:
2.7 V  V
DD  5.5 V@1 MHz to 32 MHz
2.4 V  V
DD  5.5 V@1 MHz to 16 MHz
LS (low-speed main) mode:
1.8 V  V
DD  5.5 V@1 MHz to 8 MHz
LV (low-voltage main) mode:
1.6 V  V
DD  5.5 V@1 MHz to 4 MHz
HS (high-speed main) mode only:
2.7 V  V
DD  5.5 V@1 MHz to 32 MHz
2.4 V  V
DD  5.5 V@1 MHz to 16 MHz
High-speed on-chip oscillator clock
accuracy
1.8 V  VDD  5.5 V
1.0%@ T
A = -20 to +85C
1.5%@ T
A = -40 to -20C
1.6 V  V
DD < 1.8 V
5.0%@ T
A = -20 to +85C
5.5%@ T
A = -40 to -20C
2.4 V  V
DD  5.5 V
2.0%@ T
A = +85 to +105C
1.0%@ T
A = -20 to +85C
1.5%@ T
A = -40 to -20C
Serial array unit UART
CSI: f
CLK/2 (supporting 16 Mbps), fCLK/4
Simplified I
2
C communication
UART
CSI: f
CLK/4
Simplified I
2
C communication
IICA Normal mode
Fast mode
Fast mode plus
Normal mode
Fast mode
Voltage detector Rise detection voltage: 1.67 V to 4.06 V
(14 levels)
Fall detection voltage: 1.63 V to 3.98 V
(14 levels)
Rise detection voltage: 2.61 V to 4.06 V
(8 levels)
Fall detection voltage: 2.55 V to 3.98 V
(8 levels)
(Remark is listed on the next page.)
<R>