Datasheet

RL78/G13 1. OUTLINE
Page 52 of 194R01DS0131EJ0310 Rev.3.10
Nov 15, 2013
[80-pin, 100-pin, 128-pin products]
Caution This outline describes the functions at the time when Peripheral I/O redirection register (PIOR)
is set to 00H.
(1/2)
Item 80-pin 100-pin 128-pin
R5F100Mx R5F101Mx R5F100Px R5F101Px R5F100Sx R5F101Sx
Code flash memory (KB) 96 to 512 96 to 512 192 to 512
Data flash memory (KB) 8 − 8 − 8 −
RAM (KB)
8 to 32
Note 1
8 to 32
Note 1
16 to 32
Note 1
Address space 1 MB
Main system
clock
High-speed system
clock
X1 (crystal/ceramic) oscillation, external main system clock input (EXCLK)
1 to 20 MHz: V
DD = 2.7 to 5.5 V, 1 to 8 MHz: VDD = 1.8 to 2.7 V, 1 to 4 MHz: VDD = 1.6 to 1.8 V
High-speed on-chip
oscillator
HS (High-speed main) mode: 1 to 32 MHz (VDD = 2.7 to 5.5 V),
HS (High-speed main) mode: 1 to 16 MHz (V
DD = 2.4 to 5.5 V),
LS (Low-speed main) mode: 1 to 8 MHz (V
DD = 1.8 to 5.5 V),
LV (Low-voltage main) mode: 1 to 4 MHz (V
DD = 1.6 to 5.5 V)
Subsystem clock
XT1 (crystal) oscillation, external subsystem clock input (EXCLKS)
32.768 kHz
Low-speed on-chip oscillator 15 kHz (TYP.)
General-purpose register (8-bit register × 8) × 4 banks
Minimum instruction execution time 0.03125 μ s (High-speed on-chip oscillator: fIH = 32 MHz operation)
0.05 μ s (High-speed system clock: fMX = 20 MHz operation)
30.5 μ s (Subsystem clock: fSUB = 32.768 kHz operation)
Instruction set
• Data transfer (8/16 bits)
• Adder and subtractor/logical operation (8/16 bits)
• Multiplication (8 bits × 8 bits)
• Rotate, barrel shift, and bit manipulation (Set, reset, test, and Boolean operation), etc.
I/O port Total 74 92 120
CMOS I/O
64
(N-ch O.D. I/O [EV
DD withstand
voltage]: 21)
82
(N-ch O.D. I/O [EVDD withstand
voltage]: 24)
110
(N-ch O.D. I/O [EVDD withstand
voltage]: 25)
CMOS input 5 5 5
CMOS output 1 1 1
N-ch O.D. I/O
(withstand voltage: 6
V)
4 4 4
Timer 16-bit timer 12 channels 12 channels 16 channels
Watchdog timer 1 channel 1 channel 1 channel
Real-time clock (RTC) 1 channel 1 channel 1 channel
12-bit interval timer (IT) 1 channel 1 channel 1 channel
Timer output
12 channels
(PWM outputs: 10
Note 2
)
12 channels
(PWM outputs: 10
Note 2
)
16 channels
(PWM outputs: 14
Note 2
)
RTC output
1 channel
• 1 Hz (subsystem clock: f
SUB = 32.768 kHz)
Notes 1. In the case of the 20 KB, this is about 19 KB when the self-programming function and data flash
function are used. (For details, see CHAPTER 3 in the RL78/G13 User’s Manual Hardware )
In the case of the 32 KB, this is about 31 KB when the self-programming function and data flash
function are used. (For details, see CHAPTER 3
in the RL78/G13 User’s Manual Hardware )
2. The number of PWM outputs varies depending on the setting of channels in use (the number of
masters and slaves) . (6.9.3 Operation as multiple PWM output function
in the RL78/G13 User’s
Manual Hardware
)