Datasheet
RL78/G13  2. ELECTRICAL SPECIFICATIONS (A, D: T
A = -40 to +85°C) 
Page 111 of 194R01DS0131EJ0310 Rev.3.10 
Nov 15, 2013 
(2) I
2
C fast mode 
 (T
A = −40 to +85°C, 1.6 V ≤ EVDD0 = EVDD1 ≤ VDD ≤ 5.5 V, VSS = EVSS0 = EVSS1 = 0 V) 
Parameter Symbol  Conditions  HS (high-speed 
main) Mode 
LS (low-speed 
main) Mode 
LV (low-voltage 
main) Mode 
Unit
MIN. MAX. MIN. MAX. MIN. MAX.
SCLA0 clock frequency  fSCL 
Fast mode: 
f
CLK ≥ 3.5 MHz 
2.7 V ≤ EV
DD0 ≤ 5.5 V 0  400 0  400  0  400 kHz
1.8 V ≤ EVDD0 ≤ 5.5 V 0  400 0  400  0  400 kHz
Setup time of restart 
condition 
tSU:STA 2.7 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
Hold time
Note 1
t
HD:STA 2.7 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
Hold time when SCLA0 = 
“L” 
tLOW 2.7 V ≤ EVDD0 ≤ 5.5 V  1.3  1.3  1.3 
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  1.3  1.3  1.3 
μ
s
Hold time when SCLA0 = 
“H” 
tHIGH 2.7 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
Data setup time 
(reception) 
tSU:DAT 2.7 V ≤ EVDD0 ≤ 5.5 V  100   100    100  
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  100   100    100  
μ
s
Data hold time 
(transmission)
Note 2
t
HD:DAT 2.7 V ≤ EVDD0 ≤ 5.5 V  0  0.9  0  0.9  0  0.9 
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  0  0.9  0  0.9  0  0.9 
μ
s
Setup time of stop 
condition 
tSU:STO 2.7 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  0.6  0.6  0.6 
μ
s
Bus-free time  tBUF 2.7 V ≤ EVDD0 ≤ 5.5 V  1.3  1.3  1.3 
μ
s
1.8 V ≤ EVDD0 ≤ 5.5 V  1.3  1.3  1.3 
μ
s
Notes 1.  The first clock pulse is generated after this period when the start/restart condition is detected. 
  2.   The maximum value (MAX.) of t
HD:DAT is during normal transfer and a wait state is inserted in the ACK 
(acknowledge) timing. 
Caution  The values in the above table are applied even when bit 2 (PIOR2) in the peripheral I/O redirection 
register (PIOR) is 1. At this time, the pin characteristics (I
OH1, IOL1, VOH1, VOL1) must satisfy the 
values in the redirect destination. 
Remark  The maximum value of Cb (communication line capacitance) and the value of Rb (communication line 
pull-up resistor) at that time in each mode are as follows. 
Fast mode:  C
b = 320 pF, Rb = 1.1 kΩ 










