Hardware Instruction Manual USB Evaluation Board R0K866597D020BR Hardware Instruction Manual R19AN0005EJ0100 Rev.1.00 Jan 10, 2012 Introduction This book is an instruction manual for the hardware used with evaluation board R0K866597D020BR, which operates the USB Host function and peripheral function. Target Device RX62N RSK Contents 1. Preface .............................................................................................................................................. 2 2.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 1. Preface The R0K866597D020BR is the evaluation board of the USB Host function and built-in functions. This instruction manual explains how to setup up and operate the related hardware and offers cautionary notes concerning usage. All components of the R0K866597D020BR are listed under “Table 6.2 Assembly Components and Quantity.” If you have any question about the R0K866597D020BR, contact your local distributor. R19AN0005EJ0100 Rev.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 2. Important Before using this product, be sure to read this user’s manual carefully. Keep this user’s manual, and refer to it when you have questions about this product.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Usage restrictions: This product has been developed as a means of supporting system development by users. Therefore, do not use it as an embedded device in other equipment. Also, do not use it to develop systems or equipment for use in the following fields.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 3. Precautions for Safety 3.1. Definitions of Signal Words This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read and understand this chapter before using this product. Contact us if you have any questions about the precautions described here. This chapter describes the precautions which should be taken in order to use this product safely and properly.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 3.2. Warning WARNING Warnings for Power Supply: If you connect the attached power cable with the stabilized power supply, be sure to connect it with the appropriate polarity (the red cable is connected to the power line. The black cable is connected to the ground). Use this product within the appropriate voltage range. This product does NOT have a built in over voltage protection.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 3.3. Caution CAUTION Cautions to Be Taken for Handling This Product: Use caution when handling the product. Be careful not to apply a mechanical shock. Do not touch the connector pins of this product directly. Static electricity may damage the internal circuits. When attaching and removing the cable, hold the plug of the cable and do not pull on the cable. Do not pull this product by the communications interface cable.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 4. Function Overview 4.1. Overview The R0K866597D020BR is an evaluation board for the Renesas Hi-Speed USB ASSP R8A66597FP. Two USB-A receptacles are mounted on the board for evaluation of USB host operations using USB port0 and USB port1 of R8A66597. CN1 can be used for evaluation of USB peripheral operations. Please refer to the data sheet “USB2.0 Dual Function Controller R8A66597FP” for detailed specifications of the R8A66597.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 5. Outline CN1 Port0 CN5 Port1 JA6 JA5 JP6 USB MODE JP13 WR1 SEL JA1 JA2 JP14 WR0 SEL JP8 CS SEL JP7 INT0 JP4 IOVｃｃ JA3 CN4 JP10 DC 5V SEL Figure 5.1 R0K866597D020BR Board (Top View) 6. Evaluation Board Specifications Table 6.1 Board Specifications Specifications Board Size Supply power Interface 98 mm × 88 mm AVCC , VCC : 3.3 V , VIF : 3.3 V or 1.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Table 6.2 Assembly Components and Quantity Component Name Evaluation board ( R0K866597D020BR ) Power supply cable ( incl. 2P connector ) Table of Toxic and Hazardous Substance and Elements Release Note ( English ) Release Note ( Japanese ) 6.1. QTY 1 1 1 1 1 Connector Description (View from R8A66597) Connectors JA1, JA2, JA4 and JA6 provide all bus interface pins of the chip, such as processor bus interface and DMA interface.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 6.2. Connector Description (View from RSK board) There are five connecters (JA1, JA2, JA4, JA5, and JA6) to connect with RSK boards. The following table shows the pin number and function correspondences of RSK boards. Table 6.2.1 JA1 Expansion connector Pin# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 25 26 Functions Signal I/O Pin# of R8A66597 NC 5 V Power supply 5V - GND 3.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Table 6.2.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Table 6.2.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 43 44 45 46 47 48 49 50 Address signal SDRAM Bank 3 Clock output Chip select Wait A22 B3 SDCLK CSc Wait O O O O O Address line enable SDRAM SDCLK Enable Higher-order byte data write SDRAM Data Mask Enable Lower-order byte data write SDRAM Data Mask Enable Column address select Row address select ALE CKE HWRn O O O DQM1 O LWRn O DQM0 O CAS RAS O O R19AN0005EJ0100 Rev.1.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Table 6.2.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Table 6.2.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 7. Jumper and Switch Setting Table 7.1 Power supply / GND jumper setting JP Name Factory Settings JP1 Shorted by pattern JP2 Shorted by pattern Shorted by wire Shorted by pattern JP3 JP5 Function Connecting between frame ground of CN5 and signal ground. It is necessary to cut JP1’s pattern when dividing frame ground and signal ground. Jumper for measurement of 3.3V current. It is necessary to cut JP2’s pattern when measuring 3.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Table 7.7 DC5V select jumper setting JP Name Position JP10 (DC5VSEL) EXT RSK Factory Settings O Function Connect CN4 and VBus supply device Connect JA1-1 Pin and VBus supply device Table 7.8 WR0 select jumper setting JP Name Position JP14 (WR0 SEL) WR LWR Factory Settings O Function Connect WR on RSK and WR0 on R8A66597 Connect LWR on RSK and WR0 on R8A66597 Table 7.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 8.1 Using with RSK Renesas Starter Kits are the latest development from Renesas in low-cost evaluation development toolkits. It is possible to test the R8A66597FP easily by combining it with this board and the RSK. But, it isn’t possible to test the R8A66597FP’s split bus. USB device R0K866597D020BR JA6 CN1 JA2 CN5 DC Power Supply 5V JA3 R8A66597FP CN4 JA5 JA1 JA6 JA2 JA5 JA1 Target Board JA3 e.g.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual How to use the R0K866597D020BR with the RSK is shown as below. (1) Setting of switch and jumper. (a) Set JP4 to "3.3 V". ("3.3V" is factory setting) (b) Set JP7 to "IRQ 0". ("IRQ 0" is factory setting) (c) Set JP8 to "CSa". ("CSa" is factory setting) (d) Set JP10 to "EXT". ("EXT" is factory setting) (2) Connecting the R0K866597D020BR to the RSK.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 8.2 Using with other boards This evaluation board supports separate bus mode only. (Does not support multiplex bus mode) Below are notes for target board design. 98.00 91.44 24 24 23 23 JA6 JA5 1 25 2 26 1 25 JA1 Board center 35.56 JA2 2 1 2 2 JA3 50 1 1 15.24 88.00 2 26 49 15.24 60.96 15.24 Board center Figure 8.2.1 Position of connectors chart 0.6 mm□ 2.54 mm 2.54 mm Figure 8.2.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual (1) The receptacle of the target board should suit the size of this board (refer to Figure 3 and Figure 4). Make pin arrangement the same as this board (refer to Table 1 and Table 2). Please refer to Appendix 1: the R0K866597D020BR Part List and Appendix 2: the Circuit Diagram, when selecting connector and pin arrangement. The HKP-50FD2 from Honda Tsushin Kogyo is applicable to the target board.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 9. Connectors Pin Assignment Table 9. R0K866597D020BR JA1 Pin Assignment JA1 PIN Function 1 5V 3 3V3 5 7 9 11 13 15 17 19 21 23 (SOF_N)* * : Can be connected depending on JP setting. PIN 2 4 6 8 10 12 14 16 18 20 22 24 Function GND GND Table 10. R0K866597D020BR JA2 Pin Assignment JA2 PIN Function 1 RESET 3 5 7 INT_N 9 (SOF_N)* 11 13 15 17 19 21 23 (INT_N)* 25 * : Can be connected depending on JP setting. R19AN0005EJ0100 Rev.1.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Table 11. R0K866597D020BR JA3 Pin Assignment JA3 PIN Function 1 3 A2 5 A4 7 A6 9 11 13 15 17 D0 19 D2 21 D4 23 D6 25 RD_N 27 CS_N 29 D8 31 D10 33 D12 35 D14 37 39 41 43 45 (CS_N)* 47 WR1_N 49 * : Can be connected depending on JP setting. PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Function A1 A3 A5 A7 D1 D3 D5 D7 (CS_N)* D9 D11 D13 D15 WR0_N Table 12.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual 10. Circuit Diagram See attached document. (Appendix 1) 11. Parts Layout Diagram See attached document. (Appendix 2) 12. Parts List See attached document. (Appendix 3) R19AN0005EJ0100 Rev.1.
R8A66597 USB Evaluation Board R0K866597D020BR Hardware Instruction Manual Website and Support Renesas Electronics Website http://www.renesas.com/ USB Device Page http://www.renesas.com/en/usb Inquiries http://www.renesas.com/inquiry All trademarks and registered trademarks are the property of their respective owners. R19AN0005EJ0100 Rev.1.
Revision Record Rev. 1.00 Date Jan 10.
General Precautions in the Handling of MPU/MCU Products The following usage notes are applicable to all MPU/MCU products from Renesas. For detailed usage notes on the products covered by this manual, refer to the relevant sections of the manual. If the descriptions under General Precautions in the Handling of MPU/MCU Products and in the body of the manual differ from each other, the description in the body of the manual takes precedence. 1.
Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2.
A7/ALE R32 R33 R34 0 0 0 SOF_N DACK1_N DREQ1_N 2 2 WR_N_C 3 + + 1 8 7 MBRS130T3G 2 1 1 2 12 L1 1 BLM21PG600SN1 CN7 1 C21 ZD3 1.0u TP5 1 1 C30 2 6 5 4 3 2 1 C22 1.0u HZU6.8Z 0.1 2 1 2 ID0 VBOUT0 EXTLP0 OVCUR1 VBOUT1 100 2 K3 K2 1 K4 K1 4 3 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 5 A 1 GND0 JP5 Xout 1 TP12 2 VBUS_OUT1 2 2 24MHz C27 C28 L4 2 ZD4 8pF TP14 VBUS_1 1 1 1 C26 BLM21PG600SN1 3 1 X1 4 8pF 0.1 HZU6.
Appendix2: Parts Layout Diagram 1.
2.
Appendix3 Parts List Renesas Solutions Corporation PPL-R0K866597D020BR Component Name No.
Component Name No.
Component Name No.
Component Name No. Type Symbol on Board Component Specification Product Number (specification) Manufacture Mount/ unmount Qty/set 55 Zener Diode (ZD3),(ZD4) HZU6.8Z Renesas Electronics unmount 0 56 TP (TP11),(TP12) ST-4-1 MAC8 unmount 0 57 TP (TP18),(TP19),(TP20),(TP21), (TP22),(TP23),(TP24),(TP25), (TP26),(TP27),(TP28),(TP29), (TP30),(TP31),(TP32),(TP33), (TP34),(TP35),(TP36),(TP37) WL-1 MAC8 unmount 0 58 PCB receptacle(12x2) (CN2),(CN3) HIF3H-50DA-2.
