To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.
Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office.
8 H8/300L Series User System Interface Cable For H8/300L Series Low-Cost Emulator Microcomputer Development Environment System 2003.4 www.rss.renesas.
H8/300L Series User System Interface Cable QFP 80A-Pin (SD01AC38024F80A) H8/38024 series ALE300L-H8/3800 Emulator
H8/300L Series User System Interface Cable User’s Manual Published by Date : Renesas System Solutions Asia Pte. Ltd. : April 1st, 2003, Version 1.0 Copyright (C) Renesas System Solutions Asia Pte. Ltd. All rights reserved. Trademarks (a) General All brand or product names used in this manual are trademarks or registered trademarks of their respective companies or organizations.
IMPORTANT INFORMATION • READ this user’s manual before using this emulator product. • KEEP the user’s manual handy for future reference. Do not attempt to use the emulator product until you fully understand its mechanism. Emulator Product: Throughout this document, the term ‘emulator product’ shall be defined as the following products produced only by Renesas System Solutions Asia Pte. Ltd.
LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas, at its option, will repair or replace any emulator products returned intact to the factory, transportation charges prepaid, which Renesas, upon inspection, shall determine to be defective in material and/or workmanship. The foregoing shall constitute the sole remedy for any breach of Renesas warranty.
State Law: Some states do not allow the exclusion or limitation of implied warranty or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may varies from state to state.
! WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. • Always switch OFF the emulator product and the user system before connecting or disconnecting any cables, the user system interface cable connector, and the user system IC socket.
Table of Contents SECTION 1. INTRODUCTION........................................................................................................................1-1 1.1 1.2 1.3 1.4 GENERAL DESCRIPTION .............................................................................................................................1-1 IC SOCKET TYPE .........................................................................................................................................1-1 CONFIGURATION ..........
List of Figures Figure 1.0 Figure 2.1 Figure 2.2 Figure 3.1 Figure 3.2 Figure 3.3 Figure 3.4 Figure 4.1 Main Board and QFP 80 SUB Board...............................................................................................1-1 Connect User System Interface Cable to ALE300L Emulator.....................................................2-1 Connecting user system interface cable to user system ..............................................................2-3 PCB footprint of YAMAICHI IC socket..........
Section 1. Introduction 1.1 General description The user system interface cable connects an 8-bit ALE Emulator (ALE300L-H8/3800) to the IC socket for a QFP 80A-pin package (Package code: QFP-80A) for the H8/38024 series MCU on the user system. 1.2 IC socket type The IC socket used on the user system is manufactured by YAMAICHI ELECTRONICS Co., Ltd.). The part number for the QFP-80A pin package IC socket is given below: • • 1.
1.4 Components No. 1 2 3 4 5 Component Main board QFP 80 SUB BOARD IC socket Socket cover Screws (M2x4.5) 6 Screws (M3x4.
Section 2. Connection Procedures WARNING: Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from either of the boards. Before connecting, make sure that pin 1 on both sides is correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be lost. 2.
2.2 Connecting User System Interface Cable to User System 2.2.1 Soldering IC Socket • Apply epoxy resin adhesive to the corner guides and bottom face of an IC socket for the QFP-80A pin package and fasten it to the user system. 2.2.2 Connecting the MAIN BOARD AND SUB BOARD to user system • • Align pin 1 on the IC socket with pin 1 on the QFP80 SUB BOARD, and insert the QFP80 SUB BOARD into the IC socket on the user system as shown in figure 2.2.
Figure 2.
Section 3. Dimensions for User System Cable Head The dimensions for the recommended mount pad(footprint) for the user system shown in figure 3.1 for the IC socket used on a QFP-80A-pin package (manufactured by YAMAICHI ELECTRONICS Co., Ltd. 20.50 (min) 14.70 (min) 20.50 (min) 14.70 (min) 0.65 x 19 = 12.35 ± 0.1 0.65 x 19 = 12.35 ± 0.10 Dimension for IC Socket Adapter IC149-080-017-S5 / IC149-080-017-B5 (pitch size: 0.35±0.10 or 0.05 mm) unit: mm Figure 3.
The dimensions of the Main board of the user system interface cable head is shown in figure 3.2. 31.00 84.00 62.00 Unit: mm Tolerance: +/-0.05mm Figure 3.2 User system interface cable head – Main board The dimensions of the QFP 80 SUB board of the user system interface cable head is shown in figure 3.3. 36.00 12.00 10.60 12.00 37.00 12.00 Unit: mm Tolerance: +/- 0.05mm Figure 3.
Below shows the dimension after connecting to User System Interface Cable to the user system. M3 SCREW UCON1 HEADER UCON2 HEADER MAIN BOARD 12.00 QFP80 SUB BOARD 10.00 YAMAICHI FP-80A SOCKET Unit: mm Tolerance: +/- 0.05mm Figure 3.
Section 4. Installing MCU to the User System • Check the location of pin 1 before inserting the MCU into the IC socket on the user system as shown in figure 4.1. • After inserting the MCU, fasten the socket cover with the four screws provided. • Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by over-tightening the screws or twisting the component. Figure 4.
Section 5. Warnings • Make sure that pin 1 on the IC socket is correctly aligned with pin 1 on the QFP 80 SUB board of the user cable header before inserting the QFP 80 SUB board into the IC socket on the user system. • Do not apply excessive force to the user system interface cable while it is connected to the user system. • This user system interface cable is specifically designed for the ALE300L-H8/3800 emulator. Do not use this cable with any other emulator.
Renesas Technology (Asia Sales Offices) URL: http://www.renesas.
H8/300L Series User System Interface Cable
