User`s manual

ManualsBrandsRenesas ManualsComputer equipmentPC7501

7.7.8 Specify the Events (Interrupt) ......................................................................................132

7.7.9 Specify the Events (External Trigger Signal) ..............................................................134

7.7.10 Specify the Event Combination Condition .................................................................136

7.7.11 Specify the Process ID .................................................................................................139

7.8 Protect Window .........................................................................................................................140

7.8.1 Extended Menus ............................................................................................................140

7.9 Address Interrupt Break Point Setting Window .....................................................................141

7.9.1 Command Button...........................................................................................................142

7.9.2 Setting and Deleting a Break Points from Editor(Source) Window............................143

7.10 Trace Point Setting Window...................................................................................................144

7.10.1 Specify the Trace Event...............................................................................................145

7.10.2 Specify the Combinatorial Condition..........................................................................148

7.10.3 Specify the Process ID .................................................................................................149

7.10.4 Specify the Trace Range..............................................................................................149

7.10.5 Specify the Trace Write Condition..............................................................................150

7.10.6 Command Button.........................................................................................................150

7.10.7 Specify the Events (Instruction Fetch).......................................................................151

7.10.8 Specify the Events (Memory Access) ..........................................................................151

7.10.9 Specify the Events (Bit Access)...................................................................................151

7.10.10 Specify the Events (Interrupt) ..................................................................................151

7.10.11 Specify the Events (External Trigger Signal) ..........................................................151

7.10.12 Specify the Event Combination Condition ...............................................................151

7.10.13 Specify the Process ID...............................................................................................151

7.10.14 Specify the write condition........................................................................................152

7.11 Time Measurement Window...................................................................................................156

7.11.1 Specify the Time Measurement Event........................................................................157

7.11.2 Time Measurement Condition ....................................................................................161

7.11.3 Command Button.........................................................................................................161

7.11.4 Specify the Events (Instruction Fetch).......................................................................162

7.11.5 Specify the Events (Memory Access) ..........................................................................162

7.11.6 Specify the Events (Bit Access)...................................................................................162

7.11.7 Specify the Events (Interrupt) ....................................................................................162

7.11.8 Specify the Events (External Trigger Signal) ............................................................162

7.11.9 Set the Measurement Condition .................................................................................163

7.12 Trace Window..........................................................................................................................167

7.12.1 Configuration of Bus Mode..........................................................................................167

7.12.2 Configuration of Disassemble Mode ...........................................................................169

7.12.3 Configuration of Data Access Mode............................................................................170

7.12.4 Configuration of Source Mode.....................................................................................171

7.12.5 Extended Menus ..........................................................................................................172

7.12.6 Display of bus information on the M32C Debugger...................................................173

7.12.7 Display of bus information on the M16C/R8C Debugger...........................................175

7.13 Data Trace Window.................................................................................................................176

7.13.1 Extended Menus ..........................................................................................................177

7.14 GUI I/O Window......................................................................................................................178

7.14.1 Extended Menus ..........................................................................................................179

7.15 MR Window .............................................................................................................................180

7.15.1 Extended Menus ..........................................................................................................181

7.15.2 Display the Task Status..............................................................................................182

7.15.3 Display the Ready Queue Status ................................................................................186

7.15.4 Display the Timeout Queue Status.............................................................................187

7.15.5 Display the Event Flag Status....................................................................................189

7.15.6 Display the Semaphore Status....................................................................................191

7.15.7 Display the Mailbox Status.........................................................................................193

7.15.8 Display the Data Queue Status ..................................................................................195

7.15.9 Display the Cycle Handler Status ..............................................................................197

7.15.10 Display the Alarm Handler Status ...........................................................................199

iii