SH7058 Group BP-272 User System Interface Board HS7058ECB61H User’s Manual Renesas Microcomputer Development Environment System TM SuperH Rev.3.00 2004.3.
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products.
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use.
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3.
Preface The HS7058ECB61H is a user system interface board that connects a user system for the SH7058 BP-272 package to the SH7058 E6000H emulator (HS7058EPH60H).
Contents Section 1 Configuration.....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 2.2 2.3 2.4 2.5 2.6 Connecting User System Interface Board to User System ................................................ 3 2.1.1 Installing IC Socket.............................................................................................. 3 2.1.
Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the BP-272 package. Please make sure you have all of these components when unpacking.
CAUTION Use a TQPACK256RD socket and CSPACK256Z202H01 (manufactured by Tokyo Eletech Corporation) for the BP-272 package IC socket and IC socket connector on the user system. Table 1 HS7058ECB61H Components No. Component Quantity 1 Board 1 2 IC socket 1 3 Spacer 1 For installing a BP-272 packaged MCU 4 Cover 1 For installing a BP-272 packaged MCU 5 Screws (M2 x 8 mm) 4 For installing a BP-272 packaged MCU 6 Driver 1 Dedicated screwdriver to fasten the screws.
Section 2 Connection Procedures 2.1 Connecting User System Interface Board to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST.
(4) Notes on soldering the IC socket a) The IC socket is larger than the actual IC package; therefore, refer to figure 4 for the installation of other components. b) Do not install components that occupy large volume close to the IC socket. Such components will prevent the convective flow of heat during reflow.
CAUTION 1. Never dip the IC socket in flux or use wash to clean the IC socket. This is because flux may remain inside the IC socket due to the IC socket’s structure. When using the IC socket with other DIP products, never clean the other DIP products with flux because the flux may enter the connector through the guide pins of the IC socket. 2. When an IC socket with guide pins is soldered to the user system, about 1.3 mm of the guide pins will stick out (when the user-system board is 1.6 mm thick).
2.1.2 Fastening IC Socket Connector CAUTION 1. Check the location of pin 1 before inserting. 2. Use a provided screwdriver. 3. Stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder. 4. If the emulator does not operate correctly, cracks might have occurred in the solder.
2.2 Exchanging the Spacer of the EV-Chip Board While the user system interface board is connected to the user system, force must not applied to the user system. Exchange the spacer (2.6MP x 10 mm) of the EV-chip board with another spacer (2.6MP x 25 mm) provided for the user system interface board. EV-chip board Spacer (2.
2.3 Connecting User System Interface Board to EV-Chip Board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. 2.
EV-chip board Connector No. EV-Chip Board Connector No. Board Connector No.
2.4 Recommended Dimensions for User System Mount Pad (Footprint) Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an BP-272 package (CSPACK256Z2021H01: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 6 are somewhat different from those of the actual chip's mount pad. 23.0 ± 0.03 21.3 1.0 x 19 = 19.0 1.0 Ø0.5 Unit: mm 4-Ø1.
2.5 Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 6. 120.0 8.0 100.0 5.0 5.0 Spacer EV-chip board 100.0 84.0 16.0 8.0 50.0 65.0 34.5 69.0 84.5 5.0 70.0 Top view Unit: mm Tolerance: ±0.
2.6 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 7. 8.7 28.4 53.7 EV-chip board 65.0 IC socket (Tokyo Eletech Corporation CSPACK256Z2021H01) User system Spacer (φ6.0) 45.0 45.0 65.0 Unit: mm Tolerance: ±1.
Section 3 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7058 E6000H Emulator User's Manual (HS7058EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the extended monitor and checking the bus states with the FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. 3.
To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crystal oscillator terminals on the EV-chip board.
Section 4 Notice 1. The MCU cannot be installed directly into the IC socket provided for connecting this user system interface board. 2. Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. 3. Do not apply excessive force to the user system interface board while it is connected to the user system. 4. The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MCU. 5.
SH7058 Group BP-272 User System Interface board HS7058ECB61H User's Manual Publication Date: Rev.2.00, November 20, 2003 Rev.3.00, March 1, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2003, 2004 Renesas Technology Corp. All rights reserved. Printed in Japan.
SH7058 Group BP-272 User System Interface Board HS7058ECB61H User’s Manual REJ10B0088-0300H
