REJ10J1867-0200 H8SX/1668R Group E6000H PLQP0144KA-A User System Interface Board HS1668RECH61H User’s Manual Renesas Microcomputer Development Environment System H8SX Family / H8SX/1600 Series HS1668RECH61HE Rev.2.00 Revision Date: Apr.
Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2.
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products.
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use.
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3.
VI
Preface The HS1668RECH61H is a user system interface board that connects a user system for the H8SX/1668R PLQP0144KA-A (former package: FP-144L) package to the H8SX/1650 E6000H emulator (HS1650EPH60H). Emulation of the H8SX/1668R group is only possible when this user system interface board is connected to the HS1650EPH60H.
Content Preface .........................................................................................................i Section 1 Configuration.....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Connecting the User System Interface Board to the User System .................................... 3 2.1.1 Installing the IC Socket............
Section 1 Configuration Figure 1 and table 1 show the external appearance and components, respectively, of the user system interface board for the PLQP0144KA-A package. Please make sure you have all of these components after you have unpacked the box.
CAUTION Use an NQPACK144SD-ND socket (manufactured by Tokyo Eletech Corporation) as the PLQP0144KA-A-packaged IC socket on the user system. Table 1 HS1668RECH61H Components No.
Section 2 Connection Procedures 2.1 Connecting the User System Interface Board to the User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. CAUTION 1.
To connect the board to the user system, follow the instructions below. 2.1.1 Installing the IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. CAUTION After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system. Use the guide pins provided with the product to determine where to install the IC socket, as shown in figure 2.
2.1.2 Soldering the IC Socket After fastening, solder the IC socket for a PLQP0144KA-A package to the user system. CAUTION Be sure to completely solder the leads so that the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector CAUTION Check the location of pin 1 before inserting.
2.1.4 Fastening the IC Socket Connector CAUTION 1. Use the screwdriver provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder. 3.
Screws (M2 × 10 mm) (for fastening the board) User system interface board Pin 1 User system IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) Figure 3 Connecting the User System Interface Board to the User System 7
2.2 Exchanging the Spacers of the Evaluation-Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation-chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. Evaluation-chip board Spacer (2.
2.3 Connecting the User System Interface Board to the Evaluation-Chip Board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed.
Evaluation-chip board Connector No. Evaluation-Chip Board Connector No. Board Connector No.
2.4 Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system with the IC socket for a PLQP0144KA-A package (NQPACK144SD-ND: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 6 are somewhat different from those of the mounting pad for the system with the actual MCU. 23.00 0.50 23.00 11.50 11.50 2.00 0.50 0.25 (max.) Dimension and tolerance Tolerance Dimension ±0.
2.5 Dimensions of the Evaluation-Chip Board and the User System Interface Board The dimensions of the evaluation-chip board and the user system interface board are shown in figure 7. 100.0 140.0 Evaluation-chip board 34.5 84.5 118.5 78.5 User system interface board Unit: mm Tolerance: ± 0.
2.6 Dimensions after Connecting the User System Interface Board The dimensions of the assembly after the user system interface board has been connected to the user system are shown in figure 8. 13.3 32.9 54.9 Evaluation-chip board 56.5 Spacer (φ5.8) IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) User system 45.0 45.0 56.5 Unit: mm Tolerance: ±1.
2.7 Using the Emulator without Connecting User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST.
SW1 USER OFF USER ON Figure 9 SW1 Jumper Socket Spacer (2.
Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for tightening screws. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening.
Screws (M2 x 6 mm) Socket cover MCU Pin 1 User system IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) Figure 11 Installing MCU to User System 17
Section 4 User System Interface Circuits The following user system interface circuits are required to use the emulator with the user system interface board.
User system MCU Vcc P30 P31 P34 P35 P36 P37 P20 P21 47 kΩ P30 P31 P34 P35 P36 P37 P20 P21 Sub-MCU TIOCA0 TIOCB0 TIOCA1 TIOCB1 TIOCA2 TIOCB2 TIOCA3 TIOCB3 Figure 13 User System Interface Circuit (2) 19
Vcc MCU SN74CB3Q3306A 47 kΩ P16 User system P16 Vcc 47 kΩ P15 P15 SN74CB3Q3306A P14 Sub-MCU SCK5 RxD5 TxD5 Figure 14 User System Interface Circuit (3) 20 P14
Vcc User system EPM3256ATC Sub-MCU 47 kΩ MD3 Vcc Monitoring circuit LPT16244 47 kΩ MD_CLK MD_CLK PM0-PM4 PM0-PM4 VBUS VBUS 1 kΩ DrVcc DrVcc USD- USD- USD+ USD DrVss DrVss Figure 15 User System Interface Circuit (4) 21
User system Vcc MCU EPM7128 VHC244 UHC14 47 kΩ _RES _RES EPM7128 Figure 16 User System Interface Circuit (5) User system MCU P13 P13 PB6 PB6 EPM3256ATC Vcc Sub-MCU ADTRG0 SW2 47 kΩ 1 3 Figure 17 User System Interface Circuit (6) 22
Section 5 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator User's Manual (HS1650EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the EXMONITOR_DISPLAY command (emulator command) and checking the bus states with the MEMORY_FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. 3.
⎯ To use the crystal resonator mounted on the evaluation-chip board Install the crystal resonator into the crystal resonator terminals on the evaluation-chip board.
Section 6 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both sides are correctly aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user system. 3. The dimensions of the recommended mounting pad for the IC socket for this user system interface board are different from those of the pad for the MCU. 4. This user system interface board is specifically designed for the HS1650EPH60H emulator.
Section 7 Restrictions 1. Deep-software standby mode This emulator does not support deep-software standby mode. Note that the emulator switches to the software standby mode even if the register setting to select the deep-software standby mode is made. 2. Sleep-instruction exception processing This emulator does not support the processing of sleep-instruction exceptions.
8. A/D converter In the emulator, the evaluation chip and the slave chip are used to implement functions of Unit 0 and Unit 1, respectively, of the A/D converter. For this reason, when the A/D control register (ADCR) has been set to start A/D conversion (with synchronization of units) by an external trigger from the ADTRG0 pin, the interrupt timing at the end of the A/D conversion will be different between Unit 0 and Unit 1. 9.
28
H8SX/1668R Group E6000H PLQP0144KA-A User System Interface Board HS1668RECH61H User's Manual Publication Date: Rev.2.00, April 18, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. ©2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan RENESAS SALES OFFICES http://www.renesas.com Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
H8SX/1668R Group E6000H PLQP0144KA-A User System Interface Board HS1668RECH61H User’s Manual
