REJ10J1868-0200 H8SX/1658R Group E6000H PLQP0120LA-A User System Interface Board HS1658RECN61H User’s Manual Renesas Microcomputer Development Environment System H8SX Family / H8SX/1600 Series HS1658RECN61HE Rev.2.00 Revision Date: Sep.
Rev. 2.00 Sep.
Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2.
Rev. 2.00 Sep.
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products.
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use.
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3.
Rev. 2.00 Sep.
Preface The HS1658RECN61H is a user system interface board that connects a user system for the H8SX/1658R PLQP0120LA-A (former code: FP-120B) package to the H8SX/1650 E6000H emulator (HS1650EPH60H). Emulation of the H8SX/1658R group is only possible when this user system interface board is connected to the HS1650EPH60H. Rev. 2.00 Sep.
Rev. 2.00 Sep.
Contents Section 1 Configuration ........................................................................................1 Section 2 Connection Procedures ..........................................................................3 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Connecting the User System Interface Board to the User System ......................................... 3 2.1.1 Installing the IC Socket............................................................................................. 4 2.1.
Rev. 2.00 Sep.
Section 1 Configuration Section 1 Configuration Figure 1 and table 1 show the external appearance and components, respectively, of the user system interface board for the PLQP0120LA-A package. Please make sure you have all of these components after you have unpacked the box. Evaluation-chip board Screws (M2 × 6 mm) Spacer Screws (M2 × 10 mm) (for fastening the board) Socket cover User system interface board IC socket User system Figure 1 H8SX/1658R PLQP0120LA-A User System Interface Board Rev. 2.
Section 1 Configuration CAUTION Use an NQPACK120SE-ND socket and an HQPACK120SE cover (manufactured by Tokyo Eletech Corporation) for the PLQP0120LA-A-packaged IC socket on the user system. Table 1 HS1658RECN61H Components No.
Section 2 Connection Procedures Section 2 Connection Procedures 2.1 Connecting the User System Interface Board to the User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY.
Section 2 Connection Procedures To connect the board to the user system, follow the instructions below. 2.1.1 Installing the IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. CAUTION After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system.
Section 2 Connection Procedures 2.1.2 Soldering the IC Socket After fastening, solder the IC socket for a PLQP0120LA-A package to the user system. CAUTION Be sure to completely solder the leads so that the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector CAUTION Check the location of pin 1 before inserting.
Section 2 Connection Procedures 2.1.4 Fastening the IC Socket Connector CAUTION 1. Use the screwdriver provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder. 3.
Section 2 Connection Procedures Screws (M2 × 10 mm) (for fastening the board) User system interface board Pin 1 User system IC socket (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) Figure 3 Connecting the User System Interface Board to the User System Rev. 2.00 Sep.
Section 2 Connection Procedures 2.2 Exchanging the Spacers of the Evaluation-Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation-chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. Evaluation-chip board Spacer (2.6MP × 25 mm) Figure 4 Exchanging the Spacers Rev. 2.00 Sep.
Section 2 Connection Procedures 2.3 Connecting the User System Interface Board to the Evaluation-Chip Board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed.
Section 2 Connection Procedures Evaluation-chip board Connector No. Evaluation-Chip Board Connector No. Board Connector No. UCN1 UCN1 UCN2 UCN2 User system interface board Figure 5 Connecting the User System Interface Board to the Evaluation-Chip Board Rev. 2.00 Sep.
Section 2 Connection Procedures 2.4 Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system with the IC socket for a PLQP0120LA-A package (NQPACK120SE-ND: manufactured by Tokyo Eletech Corporation). The dimensions in figure 6 are somewhat different from those of the mounting pad for the system with the actual MCU.
Section 2 Connection Procedures 2.5 Dimensions of the Evaluation-Chip Board and the User System Interface Board The dimensions of the evaluation-chip board and the user system interface board are shown in figure 7. 100.0 140.0 Evaluation-chip board 34.5 84.5 118.5 78.5 User system interface board Unit: mm Tolerance: ± 0.5 mm Figure 7 Dimensions of the Evaluation-Chip Board and the User System Interface Board Rev. 2.00 Sep.
Section 2 Connection Procedures 2.6 Dimensions after Connecting the User System Interface Board The dimensions of the assembly after the user system interface board has been connected to the user system are shown in figure 8. 13.3 32.9 54.9 Evaluation-chip board 56.5 Spacer (φ5.8) IC socket (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) User system 45.0 45.0 56.5 Unit: mm Tolerance: ±1.
Section 2 Connection Procedures 2.7 Using the Emulator without Connecting User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST.
Section 2 Connection Procedures SW1 1 3 USER OFF USER ON Figure 9 SW1 Jumper Socket Spacer (2.6MQ x 13 mm) Figure 10 Attaching Spacers Rev. 2.00 Sep.
Section 2 Connection Procedures Rev. 2.00 Sep.
Section 3 Installing the MCU on the User System Section 3 Installing the MCU on the User System CAUTION 1. Check the location of pin 1 before inserting the MCU. 2. Use a screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening.
Section 3 Installing the MCU on the User System Screws (M2.0 x 6 mm) Socket cover (HQPACK120SE manufactured by Tokyo Eletech Corporation) MCU Pin 1 IC socket (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) User system Figure 11 Installing the MCU on the User System Rev. 2.00 Sep.
Section 4 User System Interface Circuits Section 4 User System Interface Circuits The following user system interface circuits are required to use the emulator with the user system interface board. MCU SN74CBTLV3257 PD0-PD7 PE0-PE7 User system PD0-PD7 (PJ0-PJ7) PE0-PE7 (PK0-PK7) SN74CB3Q3306A PJ2, PJ3 PK2-PK7 PJ0 PJ1 PJ4 PJ5 PJ6 PJ7 PK0 PK1 Vcc 47 kΩ SN74CB3Q3306A Sub-MCU TIOCA6 TIOCB6 TIOCA7 TIOCB7 TIOCA8 TIOCB8 TIOCA9 TIOCB9 PO16-PO23 PO24-PO31 Figure 12 User System Interface Circuit (1) Rev.
Section 4 User System Interface Circuits User system Vcc MCU 47 kΩ P20 P21 Sub-MCU TIOCA3 TIOCB3 Figure 13 User System Interface Circuit (2) Rev. 2.00 Sep.
Section 4 User System Interface Circuits Vcc User system MCU SN74CB3Q3306A 47 kΩ P16 P16 Vcc 47 kΩ P15 P15 SN74CB3Q3306A P14 P14 Sub-MCU SCK5 RxD5 TxD5 Figure 14 User System Interface Circuit (3) Rev. 2.00 Sep.
Section 4 User System Interface Circuits Sub-MCU Vcc User system Monitoring circuit LPT16244 47 kΩ MD_CLK MD_CLK PM0-PM4 PM0-PM4 VBUS VBUS 1 kΩ DrVcc DrVcc USD- USD- USD+ USD DrVss DrVss Figure 15 User System Interface Circuit (4) Note: The power-supply circuit shown above is turned on/off by the setting of the SW1 jumper pin on HS1658RECN61H.
Section 4 User System Interface Circuits User system Vcc MCU VHC244 EPM7128 UHC14 47 kΩ _RES _RES EPM7128 Figure 16 User System Interface Circuit (5) User system Vcc MCU 10 kΩ P13 P13 EPM3256ATC Sub-MCU ADTRGH0 Figure 17 User System Interface Circuit (6) Rev. 2.00 Sep.
Section 4 User System Interface Circuits Rev. 2.00 Sep.
Section 5 Verifying Operation Section 5 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator User's Manual (HS1650EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the EXMONITOR_DISPLAY command (emulator command) and checking the bus states with the MEMORY_FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. 3.
Section 5 Verifying Operation ⎯ To use the crystal resonator mounted on the evaluation-chip board Install the crystal resonator into the crystal resonator terminals on the evaluation-chip board. Enlarged view Crystal resonator X1 X2 Crystal resonator terminals Evaluation-chip board Figure 19 Mounting the Crystal Resonator Rev. 2.00 Sep.
Section 6 Points for Caution Section 6 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both sides are correctly aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user system. 3. The dimensions of the recommended mounting pad for the IC socket for this user system interface board are different from those of the pad for the MCU. 4.
Section 6 Points for Caution Rev. 2.00 Sep.
Section 7 Restrictions Section 7 Restrictions 1. Deep-software standby mode This emulator does not support deep-software standby mode. Note that the emulator switches to the software standby mode even if the register setting to select the deep-software standby mode is made. 2. Sleep-instruction exception processing This emulator does not support the processing of sleep-instruction exceptions.
Section 7 Restrictions 7. A/D converter In the emulator, the evaluation chip and the slave chip are used to implement functions of Unit 0 and Unit 1, respectively, of the A/D converter. For this reason, when the A/D control register (ADCR) has been set to start A/D conversion (with synchronization of units) by an external trigger from the ADTRG0 pin, the interrupt timing at the end of the A/D conversion will be different between Unit 0 and Unit 1. 8.
H8SX/1658R Group E6000H PLQP0120LA-A User System Interface Board HS1658RECN61H User's Manual Publication Date: Rev.2.00, September 8, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan RENESAS SALES OFFICES http://www.renesas.com Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
H8SX/1658R Group E6000H PLQP0120LA-A User System Interface Board HS1658RECN61H User’s Manual
