To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.
Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office.
User’s Manual H8SX/1651 Group PLQP0120LA-A User System Interface Board for E6000H Emulator HS1651ECN61H User’s Manual Renesas Microcomputer Development Environment System H8SX Family / H8SX/1600 Series HS1651ECN61HE Rev.2.00 2008.
Rev. 2.00 Sep.
Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2.
Rev. 2.00 Sep.
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products.
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use.
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3.
Rev. 2.00 Sep.
Preface The HS1651ECN61H is a user system interface board that connects a user system for the H8SX/1651 PQLP0120LA-A (former package: FP-120B) to the H8SX/1650 E6000H emulator (HS1650EPH60H).
Contents Preface ......................................................................................................................i Section 1 Configuration...........................................................................................1 Section 2 Connection Procedures ............................................................................3 2.1 2.2 2.3 2.4 2.5 2.6 Connecting the User System Interface Board to the User System........................................ 3 2.1.
Section 1 Configuration Section 1 Configuration Figure 1 and table 1 show the external appearance and components, respectively, of the user system interface board for the PLQP0120LA-A package. Please make sure you have all of these components after you have unpacked the box. Evaluation chip board Spacer Screws (M2.0 × 10 mm) (for fastening cable head) Screws (M2.0 x 6 mm) Board Socket cover IC socket User system Figure 1 User System Interface Board for the H8SX/1651 Group PLQP0120LA-A Package Rev.
Section 1 Configuration CAUTION Use an NQPACK120SE-ND socket and an HQPACK120SE cover (manufactured by Tokyo Eletech Corporation) for the PLQP0120LA-A-packaged IC socket on the user system. Table 1 HS1651ECN61H Components No. Component Quantity Remarks 1 Board 1 2 IC socket 1 For the PLQP0120LA-A package 3 Socket cover 1 For installing an PLQP0120LA-A packaged MCU 4 Screw (M2.0 x 10 mm) 4 For fastening cable head 5 Screw (M2.
Section 2 Connection Procedures Section 2 Connection Procedures 2.1 Connecting the User System Interface Board to the User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY.
Section 2 Connection Procedures Use the guide pins provided with the product to determine where to install the IC socket, as shown in figure 2. Pin 1 Guide pins 4 projections to apply epoxy resin adhesive to IC socket (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) Bottom view of IC socket User system Figure 2 Correctly Placing the IC Socket 2.1.2 Soldering the IC Socket After fastening, solder the IC socket for an PLQP0120LA-A package to the user system.
Section 2 Connection Procedures 2.1.3 Installing the IC Socket CAUTION Check the location of pin 1 before inserting. After checking the location of pin 1 on the user system interface board and pin 1 on the IC socket connector, align the guide pins on the IC socket connector with the guide holes on the user system interface board, and insert the IC socket connector into the IC socket (figure 3). 2.1.4 Fastening the Cable Head CAUTION 1. Use a screwdriver whose head matches the screw head. 2.
Section 2 Connection Procedures Screws (M2.0 x 10 mm) Board Pin 1 IC socket (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) User system Figure 3 Connecting the User System Interface Board to the User System Rev. 2.00 Sep.
Section 2 Connection Procedures 2.2 Exchanging the Spacers of the Evaluation Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) for the evaluation chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board. Evaluation chip board Spacer (2.6MP × 25 mm) Figure 4 Exchanging the Spacers Rev. 2.00 Sep.
Section 2 Connection Procedures 2.3 Connecting the User System Interface Board to the Evaluation Chip Board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed.
Section 2 Connection Procedures Evaluation chip board Connector No. Evaluation Chip Board Connector No. UCN1 UCN2 Board Connector No. UCN1 UCN2 Board Figure 5 Connecting the User System Interface Board to the Evaluation Chip Board Rev. 2.00 Sep.
Section 2 Connection Procedures 2.4 Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system with the IC socket for an PLQP0120LA-A package (NQPACK120SE-ND: manufactured by Tokyo Eletech Corporation). The dimensions in figure 6 are somewhat different from those of the mounting pad for the system with the actual MCU.
Section 2 Connection Procedures 2.5 Dimensions of the Evaluation Chip Board and the User System Interface Board The dimensions of the evaluation chip board and the user system interface board are shown in figure 7. 100.0 140.0 Evaluation chip board 118.5 16.0 34.5 69.0 84.5 102.5 78.5 User system interface board Unit: mm Tolerance: ± 0.5 mm Figure 7 Dimensions of the Evaluation Chip Board and the User System Interface Board Rev. 2.00 Sep.
Section 2 Connection Procedures 2.6 Resulting Dimensions after Connecting the User System Interface Board The dimensions of the assembly after the user system interface board has been connected to the user system, are shown in figure 8. 13.3 32.9 54.9 Evaluation chip board 56.5 Spacer (φ5.8) IC socket (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) User system 45.0 45.0 56.5 Unit: mm Tolerance: ±1.
Section 3 Installing the MCU on the User System Section 3 Installing the MCU on the User System CAUTION 1. Check the location of pin 1 before inserting the MCU. 2. Use a screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening.
Section 3 Installing the MCU on the User System Screws (M2.0 x 6 mm) Socket cover (HQPACK120SE manufactured by Tokyo Eletech Corporation) MCU Pin 1 IC socket (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) User system Figure 9 Installing the MCU on the User System Rev. 2.00 Sep.
Section 4 Verifying Operation Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator User's Manual (HS1650EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the CHECK command (emulator command) and checking the bus states with the FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. 3.
Section 4 Verifying Operation ⎯ To use the crystal oscillator mounted on the evaluation chip board Install the crystal oscillator into the crystal oscillator terminals on the evaluation chip board. Enlarged view Crystal oscillator X1 X2 Crystal oscillator terminals Evaluation chip board Figure 11 Installing the Clock Oscillator Rev. 2.00 Sep.
Section 5 Restriction on the Interface Section 5 Restriction on the Interface The following restriction applies to the interface when pins PF7, PF6, and PF5 of the MCU are selected as CS-output pins by the emulator, to which the user system interface board is connected. Jumper pins (SW1 to SW3) are used to switch the functions of pins PF7, PF6, and PF5 between port and CS-output functions. While these pins are in use as CS-output pins, the functions of PF7, PF6, and PF5 are disabled.
Section 5 Restriction on the Interface Rev. 2.00 Sep.
Section 6 Points for Caution Section 6 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both sides are correctly aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user system. 3. The dimensions of the recommended mounting pad for the IC socket for this user system interface board are different from those of the pad for the MCU. 4.
Section 6 Points for Caution Rev. 2.00 Sep.
H8SX/1651 Group PLQP0120LA_A User System Interface Board for E6000H Emulator User's Manual Publication Date: Rev.2.00, September 8, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan RENESAS SALES OFFICES http://www.renesas.com Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
H8SX/1651 Group PLQP0120LA-A User System Interface Board for E6000H Emulator HS1651ECN61H User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10J1394-0200
