Flash memory MCU On-board Programmer FLASH1 User’s Manual Windows95, 98 - Please read this carefully before using the product - F-ZTATTM is a trademark of Renesas Electronics. Windows 95 and Windows 98 are products of Microsoft Corporation. HokutoElectronic Co., Ltd. REV.2.0.2.
--- Contents --- ● GENERAL PRECAUTION 2 ● FLASH1 OUTLINE 3 ● CONTENTS 3 THE PROVIDED CD INCLUDES 3 SPECIFICATIONS 4 FLASH1 THE IMAGE OF THE CASE 4 BATTERY HOLDER GUIDANCE PREPARATION 1 5 - CONNECTOR & CABLE – 6 FLASH1 INTERFACE CIRCUIT DIAGRAM 6 REFERENCE CIRCUIT DIAGRAM FOR TARGET BOARD 6 SIGNAL-NAME OF REQUIRED RS232C STRAIGHT CABLE 7 SIGNALS BETWEEN FLASH1 AND TARGET BOARD 7 CABLE-CONNECTOR-TYPE-NAME BETWEEN TARGET BOARD AND FLASH1 7 ● PREPARATION 2 ● BASIC OPERATION -
● General Precaution Make sure that you fully understood this user’s manual, before using the FLASH1 and power adapter. Reading the manual is the responsibility of the FLASH1 users to fully understand all the matters. ● Make sure that you fully understood this user’s manual, before using WARNINGS Failure to adhere to the following warnings may result in possible heat, smoke and fire damage to FLASH1 and surrounding systems. 1. Don't disconnect and don't reconnect power cables while power is on. 2.
● FLASH1 Outline FLASH1 has been designed to program flash memory MCU, made by Renesas Electronics. This FLASH1 circuit management at writing to memory is fully automated. Writing to the target MCU from the user's PC can be carried out without switch operation smoothly. All of Renesas Electronics dual power supply flash memory MCU is available to reprogram on board. Attached in this kit, the sample software provides an easy way of confirming the LED movement on the boards HSB series, of our product.
Specifications MCU available: All the Renesas Electronics flash memory MCU of dual power supply H8/538F・H8/539F・H8/3644F(H8/3642RF・H8/3643F) H8/3048F・H8/3334YF・H8/3337YF・H8/3434F・H8/3437F Programming mode: Only in boot mode Target MCU: FVPP=12V (UserVcc is within 2.5~5.5V. Vpp terminal is 60 mA.
Battery Holder Guidance Please read before placing the batteries into the battery holder. <Precaution> Some of the alkaline batteries contain flexible insulating label to it. When placing that kind of batteries into the battery holder, negative terminal (-) of the battery holder could come into contact with positive terminal (+) inside of the flexible insulating label as shown in the diagram below. It causes electrical short-circuit. Please do not use the batteries described above.
● Preparation 1 - Connector & Cable – FLASH1 Interface Circuit Diagram FLASH1 programming interface (10P) Target board programming interface (8P) ILS8S Provided target cable Reference Circuit Diagram for Target Board USER VCC TXD RXD USER VCC USER VCC VPP 1 2 USER VCC 3 12KΩ USER VCC 4 5 1UF 0.
Signal-name of Required RS232C Straight Cable PC9801with 25 pins connector PC 25pins programmer 1 2 3 4 5 6 7 20 1 2 3 4 5 6 7 20 DOS/V series with 9 pins connector 25pins PC 9pins programmer 2 3 4 5 6 7 8 2 3 4 5 6 7 20 25pins Caution! :The no.4 & 5 lines of the programmer side must be connected appropriately, because of the importance for the steady control form “FLASH1 for Windows”.
● Preparation 2 - Installation of Control Software – When the setup program finds the same file name in your PC, the setup program will display the caution recommending you to avoid overwriting. We recommend you to use the file of the install-disk. When using this control software without overwriting, guarantee is not valid. And also we can’t guarantee any reflections happened to other applications that well worked before this installation.
● Basic Operation Prepare target board Please refer to preparation 1 HSB board can be used as it is.
Other Expendable Supplies Expendable Supplies Name AC 100 volt Adapter FLASH1 Target Cable (10p) Price ¥2500 ¥1200 Notes Verified only in Japan Available for FLASH MATE 12V1 Please confirm about the charges for above. Please visit our web site for the latest information. http://www.hokutodenshi.co.jp For technical support support@hokutodenshi.co.jp FLASH1 USER'S MANUAL–ForWin– ©2000-2013 北斗電子 Printed in Japan HokutoElectronics Co., Ltd.