To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.
Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office.
M32C PC4701 Emulator Debugger V.1.03.00 Release Notes This document describes the notes of this debugger, and please read before you start to use this debugger. And also, please refer to the “High-performance Embedded Workshop Release Notes” about the notes of High-performance Embedded Workshop IDE. Contents 1 Notes ..................................................................................................................................................... 2 1.1 Line Assembly .......................
1 Notes 1.1 Line Assembly Regardless of the Radix setting, the default for line assembly input is decimal. Specify H as the radix for a hexadecimal input. 1.2 Event Setting 1. TAB order in Set Event Status dialog box Even when you press [TAB] key, the next input control may not be focused on the Set Event Status dialog boxes opened from H/W Break, Time Measurement, and Trace Point. 2.
of the start-up module will be returned even if scope has been changed to the other. 1.8 Real-time OS debugging functions 1. When several labels are allocated to the entry address of the tasks or handlers, the task name or the handler name displayed in the windows may be different from the actual function name. 2. When you use the feature to issue system-calls by the script command (MR SYS), the target program should be built with a specific option.
! ! ! ! Change the ram monitor area in RAM Monitor Window Add or remove software break points Change the status of hardware break points Get the trace information forcibly or re-start recording the trace information in Trace Window 1.14 The option “Always treat variables of enumerator type with unknown size as 1 byte” The “Always treat variables of enumerator type with unknown size as 1 byte” option is effective after downloading the program.
1. When using Windows XP or Windows 2000 Key HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\ Parameters\SackOpts Value 0 (REG_DWORD) You can set this registry by executing the registry setup program, "Sack.exe". And you can clear the registry with running the program "UnSack.exe". - Sack.exe", the program setting the registry. - Unsack.exe", the program clearing the registry.
2 System Requirements 2.1 M32C PC4701 Emulator Debugger Target host PC PC OS Memory HDD Display Resolution Emulator PC4701U IBM PC/AT compatible with Pentium III 600MHz or higher Windows XP Windows 2000 128MB or more (and in addition, ten or more times as much size as the load module file). Hard disk available capacity for installation: 100MB or more. Prepare an area at least double the memory capacity (four-times or more recommended) as the swap area.
3 Version Report This section describes the specification of the changed software. 3.1 M32C PC4701 Emulator Debugger V.1.03.00 In this version, the following specifications were changed from the previous version M32C PC4701 Emulator Debugger V.1.02.00. This version supports all of the function extensions and the revisions to the restrictions in the High-performance Embedded Workshop V.4.02.00 and V.4.03.00.
For more details, refer to the RENESAS TOOL NEWS RSO-M3T-PD32RM-060116D issued on January 16, 2006. 2. A limitation has been corrected: If the Task Pause button is pressed while a service call is being serviced, the target task of the service call does not enter the pause state but goes to the object-waiting state though it is displayed in the debugger screen that the task has entered the pause state. For more details, refer to the RENESAS TOOL NEWS RSO-M3T-MR308-060416D issued on April 16, 2006. 3.2.2 3.
