To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.
Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office.
User’s Manual M306H5T3-RPD-E User’s Manual Emulation Pod for M16C/6H Group M306H5 Rev.1.00 2004.
Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
M306H5T3-RPD-E User’s Manual Preface Preface The M306H5T3-RPD-E is an emulation pod for the M16C/6H Group M306H5 of 16-bit MCUs. It is used with a PC4701 emulator (excluding the PC4700L and PC4701L). This user's manual mainly describes specifications of the M306H5T3-RPD-E emulation pod and how to setup it. For details on the following products, which are used with the M306H5T3-RPD-E, refer to each product's user's manual or online manual. All the components of this product are shown in "1.
M306H5T3-RPD-E User’s Manual Important Important Before using this product, be sure to read this user’s manual carefully. Keep this user’s manual, and refer to this when you have questions about this product. Emulator: The emulator in this document refers to the following products that are manufactured by Renesas Technology Corp.
M306H5T3-RPD-E User’s Manual Important Usage restrictions: This emulator has been developed as a means of supporting system development by users. Therefore, do not use it as a device used for equipment-embedded applications.
M306H5T3-RPD-E User’s Manual Precautions for Safety Precautions for Safety Definitions of Signal Words In both the user’s manual and on the product itself, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product.
M306H5T3-RPD-E User’s Manual Precautions for Safety 警告警告 WARNING Warnings for AC Power Supply: If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. Use an AC power cable which complies with the safety standard of the country. Do not touch the plug of the AC power cable when your hands are wet. This may cause electric shock. This product is connected signal ground with frame ground.
M306H5T3-RPD-E User’s Manual Precautions for Safety CAUTION 注意注意 Cautions to Be Taken for Turning On the Power: Turn ON the power of the emulator and user system as simultaneously as possible. Turn OFF the power of the emulator and user system as simultaneously as possible. Do not leave either the emulator or user system powered on, because of leakage current the internal circuits may be damaged. When turning ON the power again after shutting OFF the power, wait about 10 seconds.
M306H5T3-RPD-E User’s Manual Contents Contents Page Preface .................................................................................................................................................................................. 3 Important ............................................................................................................................................................................... 4 Precautions for Safety ..........................................................
M306H5T3-RPD-E User’s Manual Contents Page 4. Hardware Specifications .................................................................................................................................................. 42 4.1 Target MCU Specifications.......................................................................................................................................... 42 4.2 Operation Timing in Memory Expansion and Microprocessor Modes .....................................................
M306H5T3-RPD-E User’s Manual Contents Page 5. Troubleshooting............................................................................................................................................................... 59 5.1 Flowchart to Remedy the Troubles ............................................................................................................................. 59 5.2 When the Emulator Debugger Does Not Start Up Properly ..............................................................
M306H5T3-RPD-E User’s Manual User Registration User Registration When you have purchased the emulator presented in this user's manual, please be sure to register it. As the hardware tool user registration FAX sheet is included with this manual, fill it in and FAX it to your local distributor or email the same contents to the following address. Your registered information is used for only after-sale services, and not for any other purposes.
M306H5T3-RPD-E User’s Manual Terminology Terminology Some specific words used in this user's manual are defined as follows: Emulator system This means an emulator system built around the PC4701 emulator. The PC4701 emulator system is configured with an emulator main unit, emulation pod, host machine and emulator debugger. Emulator main unit (Hereafter PC4701) This means a generic name for emulators for M16C, 7700, 740 Families.
M306H5T3-RPD-E User’s Manual 1. Outline 1. Outline This chapter describes the package components, the system configuration and the preparation for using this product for the first time. 1.1 Package Components The M306H5T3-RPD-E package consists of the following items. When unpacking it, check to see if your M306H5T3-RPD-E contains all of these items. Table 1.
M306H5T3-RPD-E User’s Manual 1. Outline 1.3 System Configuration 1.3.1 System Configuration Figure 1.1 shows a configuration of the PC4701 system. Emulator debugger Interface cable Host machine (2) Flexible cable connecting PC 4701 (1) Emulation pod main unit Emulator main unit (3) Flexible cable connecting user system (4) Pitch converter board for connecting user system Figure 1.
M306H5T3-RPD-E User’s Manual 1. Outline 1.3.2 Names and Functions of the PC4701 Front Panel LEDs Figure 1.2 shows the names of the LEDs on the front panel of the emulator. Target status LED STATUS OF TARGET P OWE R PO WER SAFE CLO CK E RRO R RE SE T STATUS OF RUN System status LED SYSTEM HALT RES E T PC4701U HIGH PERFORMANCE EMULATION BENCH Figure 1.
M306H5T3-RPD-E User’s Manual 1. Outline (2) Target Status LEDs The target status LEDs indicate the target MCU's operating status and target board's power supply. Table 1.4 lists the definition of each target status LED. Table 1.4 Definitions of the target status LEDs Name Status Meaning ON Power is supplied to the target MCU. POWER OFF Power is not supplied to the target MCU. ON Target MCU clock is supplied. CLOCK OFF Target MCU clock is not supplied. ON Target MCU is being reset.
M306H5T3-RPD-E User’s Manual 1. Outline 1.4 Specifications Tables 1.5 lists the specifications of the M306H5T3-RPD-E. Table 1.5 M306H5T3-RPD-E specification Item Desctiption Applicable MCU M16C/6H Group M306H5 Evaluation MCU M306H3FCFP and M306H5MG-002FP (1 piece each) Single-chip mode Memory expansion mode Usable mode Microprocessor mode Emulation Memory 1MB Maximum operating frequency 16MHz VCC2=4.0V--5.5V, VCC1=3.0V--VCC2 (Xin: when operating without division) VCC2=2.9V--5.5V, VCC1=2.
M306H5T3-RPD-E User’s Manual 1. Outline 1.5. Operating Environment Be sure to use this emulator with the operating environmental of the emulator and host machine listed in Tables 1.6 and 1.7. Table 1.6 Operating environmental conditions Item Operating temperature 5 to 35°C (no dew) Storage temperature -10 to 60°C (no dew) Description Table 1.
M306H5T3-RPD-E User’s Manual 2. Setup 2. Setup This chapter describes the preparation for using this product, the procedure for starting up the emulator and how to change settings. 2.1 Removing/Attaching the Upper Cover To use this emulation pod with your user system, it is necessary to set as follows. Set the following after removing the upper cover.
M306H5T3-RPD-E User’s Manual 2. Setup 2.2 Each Setting Figure 2.2 shows the positions of the following parts. (1) (2) (3) (4) Oscillator circuit board Switches Socket for mounting network resistor for pullup Bypass capacitor for A/D converter (3) Socket for mounting network resistor for pullup (2) Switches (1) Oscillator circuit board M306H5T3-PRT REV.
M306H5T3-RPD-E User’s Manual 2. Setup 2.3 Selecting Clock Supply and Replacing Oscillator Circuit Boards 2.3.1 Clock Supply to the MCU There are two ways to supply a clock to the MCU, using the oscillator circuit of the emulation pod or using the oscillator circuit on the user system. Table 2.1 lists the factory-settings of each clock supply when you install the emulator debugger.
M306H5T3-RPD-E User’s Manual 2. Setup 2.3.2 Using the Internal Oscillator Circuit Board An oscillator circuit board for 16.0 MHz (OSC-3) is mounted on this product. Also the oscillator circuit board (OSC-2) is attached to change the oscillation frequency. When you use an internal oscillator circuit as a main clock, “Internal” can be set by the emulator debugger. 2.3.3 Changing the Internal Oscillator Circuit of the Emulation Pod To use the emulation pod at a frequency other than 16.
M306H5T3-RPD-E User’s Manual 2. Setup 2.3.4 Replacing Oscillator Circuit Boards Figure 2.5 shows how to replace the oscillator circuit boards. For the position of the oscillator circuit board, see Figure 2.2. Unscrew the screw securing the oscillator circuit board. Lift off the oscillator circuit board. Insert the J1 connector of a new oscillator circuit board to the connector of the main board. Secure the new oscillator circuit board with the screw. Figure 2.
M306H5T3-RPD-E User’s Manual 2. Setup 2.3.5 Using the Oscillator Circuit on the User System To operate this product with an external clock, construct the oscillator circuit as shown in Figure 2.6 in the user system and input the oscillator output at 50% duty (within the operating range of the evaluation MCU) into pin XIN. And pin XOUT should be open. Choose "External" in the emulator debugger to use this clock. Figure 2.
M306H5T3-RPD-E User’s Manual 2. Setup 2.4 Switch Settings Here follows explanations of the switches of the M306H5T3-RPD-E. Tables 2.2 and 2.3 list how to set toggle switches SW1 to SW6 of the M306H5T3-PRT board (MCU-dependent). Tables 2.4 and 2.5 list how to set jumper switches JP2 to JP9 on the M306H5T3-PRT (MCU-dependent board). 2.4.1 Toggle Switches SW1 to SW6 on the M306H5T3-PRT Board (MCU-dependent) Table 2.
M306H5T3-RPD-E User’s Manual 2. Setup Table 2.3 Switch settings of the M306H5T3-RPD-E (2) Signal Switch Setting P87 P87/Xcin SW4 (Factory-setting) Xcin P87 Description Sets pin P87/Xcin to port P87 and connects to the user system. Sets pin P87/Xcin to Xcin and connects to the user system. Xcin OPEN Does not connect pin Xout to the user system. Xout SW5 (Factory-setting) Xout OPEN Does not connect pin Xout to the user system.
M306H5T3-RPD-E User’s Manual 2. Setup 2.4.2 Jumper Switches JP2 to JP9 on the M306H5T3-PRT Board (MCU-dependent) Table 2.4 Switch settings of the M306H5T3-RPD-E (3) Signal Switch Setting of jumper switches FLX CVIN1 JP2 SYNCIN JP3 SVREF JP4 TEST3 JP5 FLX INT INT Connects pin CVIN1 to internal Connects pin CVIN1 to the user circuit of the M306H5T3-PRT. system via the M3T-FLX160C.
M306H5T3-RPD-E User’s Manual 2. Setup Table 2.5 Switch settings of the M306H5T3-RPD-E (4) Signal JC1_R TVDD Switch Setting of jumper switches JC1_R JC1_R Does not pull down video input signal (RCA connector). Pulls down video input signal (RCA connector) with a resistance of 75 Ω (Factory-setting) JP8 JP9 V50 TVDD Do not use this setting. V50 TVDD Be sure to use this setting. (Factory-setting) CAUTION Note on Switch Settings: Always shut OFF power before changing switch setting.
M306H5T3-RPD-E User’s Manual 2. Setup 2.5 Installing and Removing Network Resistors for Pullup In this product, you cannot control pullup for ports P0 to P5 by pullup control registers (pullup control register read/write are possible). A socket for installing the network resistor for pullup is mounted in this product. Mount the 51 kΩ network resistor supplied with this product to the port for which pullup control is required. For the mounting location, refer to Figure 2.8 below.
M306H5T3-RPD-E User’s Manual 2. Setup 2.6 Bypass Capacitors for A/D Converter The M306H5T3-RPD-E has the M306H5T3-PRT board which has a foot pattern for installing bypass capacitors for A/D converter near the MCU and premounted 0.1µF capacitors. Mount suitable bypass capacitors as occasion demands. Figure 2.2 shows where they are installed and Figure 2.9 shows their connection. IC6 C8 AVSS Vref AVSS AVCC M306H5MG-002FP C9 Figure 2.
M306H5T3-RPD-E User’s Manual 2. Setup 2.7 Connection Diagram of Data Slicer This product has on-board sockets to change parts used for circuits connected to a data slicer. The circuit and the arrangement of the parts used for each circuit are shown in Figure 2.10 and Figure 2.11, respectively.
M306H5T3-RPD-E User’s Manual 2. Setup 2.8 Connecting the PC4701 To connect the emulation pod to the PC4701, use the FLX120-RPD 120-pin flexible cable included with this product package. Connect the PC4701 side connector of the FLX120-RPD to the cable connector of the PC4701, then secure with screws the FLX120-RPD. 2.8.1 Connecting the Cable to the PC4701 Figure 2.12 shows how to connect the PC4701 and FLX120-RPD. Emulator main unit PC4701 side connector of FLX120-RPD UPSIDE should be face up .
M306H5T3-RPD-E User’s Manual 2. Setup 2.8.2 Connecting the Cable to the Emulation Pod Figure 2.13 shows how to connect the FLX120-RPD and the emulation pod. Emulation pod FLX120-RPD (Secure with the screws) Figure 2.13 Connecting the cable to the emulation pod CAUTION Note on Connecting the Cable: Always shut OFF power before connecting the cable. Otherwise, the internal circuits may be damaged.
M306H5T3-RPD-E User’s Manual 2. Setup 2.9 Connecting the User System Connect the emulation pod to the user system as shown in Figure 2.14. (1) (2) (3) (4) Mount the NQPACK116SB to the user system. Attach the YQPACK116SB to the NQPACK116SB. Fix the YQPACK116SB with the included YQ-GUIDE's. Attach the CN2 side of the M306H2T-PTC to the tip (CN2 side) of the pitch converter board FLX160-PRB connected to the emulation pod probe. (5) Attach the M306H2T-PTC to the fixed YQPACK116SB.
M306H5T3-RPD-E User’s Manual 3. Usage 3. Usage This chapter describes the setting when you use this product for the first time and the workflow, from turning on the power of this product to starting up the emulator debugger. . 3.1 When Using This Product for the First Time 3.1.1 Making an MCU File It is necessary to make an MCU file to use this product with the emulator debugger M3T-PD30. According to the MCU you use, change the contents of the MCU file.
M306H5T3-RPD-E User’s Manual 3. Usage 3.2 Turning On the Power 3.2.1 Checking Connections of the Emulator System Before turning the power ON, check the connections of the PC4701, emulation pod, converter board and user system. 3.2.2 Turning ON/OFF the Power (1) Turn on the power of the emulator and user system as simultaneously as possible. (2) Turn off the power of the emulator and user system as simultaneously as possible.
M306H5T3-RPD-E User’s Manual 3. Usage 3.2.3 LED Display When the Emulator Starts Up Normally After the emulator starts up, check the status of the LEDs on the front panel to see whether emulation pod operation is enabled or not. Figure 3.1 shows front panel LED lighting status when the emulator is turned ON. - When this does not light, check the power supply of the user system. - Check that power is supplied to all the terminals. - This does not light when the user system is not connected.
M306H5T3-RPD-E User’s Manual 3. Usage 3.3 Downloading Firmware 3.3.1 When It is Necessary to Download Firmware It is necessary to download the firmware in the cases listed below. Normally, the following are automatically detected when the emulator debugger is started up, and the firmware is downloaded.
M306H5T3-RPD-E User’s Manual 3. Usage 3.4 Self-check 3.4.1 Self-check Procedure To run the self-check of the emulator, do so as explained here below. While the self-check is in progress, the LEDs will change as shown in Figure 3.4. (1) If the user system is connected, disconnect it. (2) Set the switches in the emulation pod to the factory settings as shown in Figure 3.3.
M306H5T3-RPD-E User’s Manual POWER P OWE R S AFE ERROR S T A T US OF 3.
M306H5T3-RPD-E User’s Manual 4. Specifications 4. Hardware Specifications This chapter describes specifications of this product. 4.1 Target MCU Specifications Table 4.1 lists the specifications of target MCUs which can be debugged with this product. Table 4.1 Specifications of target MCUs for the M306H5T3-RPD-E Item Description Applicable MCU M16C/6H Group M306H5 Applicable MCU mode Single-chip mode, memory expansion mode, microprocessor mode Emulation Memory 1 MB Max. operating frequency 16MHz (VCC2=4.
M306H5T3-RPD-E User’s Manual 4. Specifications Vcc=5V 4.2 Operation Timing in Memory Expansion and Microprocessor Modes 4.2.1 Separate Bus Timing Table 4.2 and Figure 4.1 show the bus timing in memory expansion and microprocessor modes (3-wait, accessing external area). Table 4.2 Memory expansion and microprocessor modes (3-wait, accessing external area) Actual MCU This product [ns] Symbol Item [ns] Min. Max. Min. Max.
M306H5T3-RPD-E User’s Manual 4.
M306H5T3-RPD-E User’s Manual 4. Specifications Vcc=5V 4.2.2 Multiplex Bus Timing Table 4.3 and Figure 4.2 show the bus timing in memory expansion and microprocessor modes (2-wait, accessing external area, using multiplex bus). Table 4.
M306H5T3-RPD-E User’s Manual 4.
M306H5T3-RPD-E User’s Manual 4. Specifications Vcc=5V 4.2.3 Timing Requirements Table 4.4 and Figure 4.3 show the timing requirements. Table 4.4 Timing requirements Symbol Actual MCU [ns] Min. Max. 40 30 40 0 0 0 40 Item tsu(DB-RD) tsu(RDY-BCLK) tsu(HOLD-BCLK) th(RD-DB) th(BCLK-RDY) th(BCLK-HOLD) td(BCLK-HLDA) Data input setup time RDY* input setup time HOLD* input setup time Data input hold time RDY* input hold time HOLD* input hold time HLDA* output delay time This product [ns] Min. Max.
M306H5T3-RPD-E User’s Manual 4. Specifications 4.3 Differences between the Actual MCU and Emulator Differences between the actual MCU and emulator are shown below. When debugging the MCU using this product, be careful about the following precautions. IMPORTANT Note on Differences between the Actual MCU and Emulator: Operations of the emulator system differ from those of actual MCUs as listed below. (1) Reset condition Set the time for starting up (0.2 Vcc to 0.8 Vcc) 1 µs or less.
M306H5T3-RPD-E User’s Manual 4. Specifications IMPORTANT Note on NMI* Input: L" input from the user system to pin NMI* is accepted only while a user program is being executed (only while the RUN status LED on the PC4701's front panel is lit). Note on RDY* Input: Be sure to input "L" to pin RDY* of the user system during the user program executing (only while the RUN status LED on the PC4701's front panel is lit).
M306H5T3-RPD-E User’s Manual 4. Specifications 4.4 Connection Diagram Figure 4.4 shows a connection diagram of the M306H5T3-RPD-E. This connection diagram mainly shows the interface section. The circuits not connected to the user system such as the emulator's control system are omitted. The signals not shown in Figure 4.4 connect the evaluation MCU and the user system directly. Tables 4.6 to 4.8 show IC electric characteristics of this product for reference purposes.
M306H5T3-RPD-E User’s Manual 4. Specifications Table 4.6 Electrical characteristics of the 74HC4066 Symbol RON ∆RON IOFF IIZ Item ON resistor ON resistor difference Leak current (Off) Leak current (On, output: open) Condition Vcc=4.5V Vcc=4.5V Vcc=12.0V Vcc=12.0V Min. - Standard values Standard Max. 96 200 10 ±1 ±1 Unit [Ω] [µA] Table 4.
M306H5T3-RPD-E User’s Manual 4. Specifications 4.5 External Dimensions 4.5.1 External Dimensions of the Emulation Pod Figure 4.5 shows external dimensions of the M306H5T3-RPD-E. 40 . 0 11.0 10 . 5 33.0 11.0 189.0 437.0 193 .0 3.0 3.0 140.0 52.0 Unit: mm Figure 4.5 External dimensions of the emulation pod REJ10J0866-0100Z Rev.1.00 Dec.
M306H5T3-RPD-E User’s Manual 4. Specifications 4.5.2 External Dimensions of the Converter Board M306H2T-PTC Figure 4.6 shows external dimensions of the pitch converter board M306H2T-PTC for 116-pin LQFP (116P6A-A) and a sample foot pattern for NQPACK116SB. 55 . 0 21 . 8 40a 40b 51 75 CN2 CN1 26 100 M306H2T -PTC REV . A 50 76 MADE I N JAPAN 40a 40b 0 . 25 19 . 00 40 . 0 2 3 . 00 0 . 65 25 1a IC1 1a 1b 19 . 00 16 . 5 23 . 00 Unit: mm Figure 4.
M306H5T3-RPD-E User’s Manual 4. Specifications 4.6 Precautions for Safety This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product. IMPORTANT Note on Malfunctions in the PC4701 System If the emulator malfunctions because of interference like external noise, do the following to remedy the trouble (1) Press the RESET switch on the emulator upper panel.
M306H5T3-RPD-E User’s Manual 4. Specifications IMPORTANT Note on Clock Supply to the MCU: A clock supplied to the evaluation MCU is selected by the Clock tab in the Init dialog box of the emulator debugger. (1) When Internal is selected: A clock generated by the oscillation circuit in the emulation pod is supplied to the evaluation MCU.
M306H5T3-RPD-E User’s Manual 4. Specifications IMPORTANT Notes on MAP References and Settings: For details on referencing and setting MAP information, see the emulator debugger M3T-PD30 user's manual. Make settings as follows: (1) MAP = INT The emulation memory inside this product becomes effective. Set this at MCU internal ROM debugging. (2) MAP = EXT The emulation memory inside this product is not used. Set this where the MCU internal resource (SFR) or resources on the user system are used.
M306H5T3-RPD-E User’s Manual 4. Specifications IMPORTANT Notes on Address-Match Interrupts: To debug address-match interrupts, set a software break or hardware break at the top address of the address-match interrupt process. If you set a software break or hardware break at an address where an address-match interrupt occurs, the program may run out of control.
M306H5T3-RPD-E User’s Manual 4. Specifications IMPORTANT Note on Reading Internal Resources of the MCU: When the registers listed in Table 4.9 are read with an emulator, those results will be the following (the data in the MCU are not effected). (1) Results of real-time trace The data values of the cycles read are not displayed correctly. (2) Real-time RAM monitor The data values read are not displayed correctly. Table 4.
M306H5T3-RPD-E User’s Manual 5. Troubleshooting 5. Troubleshooting This chapter describes how to troubleshoot when this product does not work properly. 5.1 Flowchart to Remedy the Troubles Figure 5.1 shows the flowchart to remedy troubles from when power to the emulator is activated until the emulator debugger starts up. Check this while the user system is not connected. For the latest FAQs visit the Renesas Tools Homepage. http://www.renesas.
M306H5T3-RPD-E User’s Manual 5. Troubleshooting 5.2 When the Emulator Debugger Does Not Start Up Properly 5.2.1 When the LED Display of the PC4701 is Abnormal Table 5.1 LED's abnormal display and its checkpoints Connection to Error Checkpoint the user system Check that the power cable is connected to the PC4701. LEDs do not light up. See the PC4701 user's manual. Check the connection between the PC4701 and this product. All LEDs remain lit. See "2.8 Connecting the PC4701" (page 33).
M306H5T3-RPD-E User’s Manual 5. Troubleshooting 5.2.2 Program Window is Not Displayed at Debugger Startup (Target Connected) Table 5.2 Checkpoints of errors when starting up the emulator debugger (target connected) Error Checkpoint ERROR 16005: (1) Check the connection between the PC4701 and host machine. Can't connect with the target. See the PC4701 User's Manual. (2) Check that the PC4701 is powered on. See the PC4701 User's Manual.
M306H5T3-RPD-E User’s Manual 5. Troubleshooting 5.2.3 Program Window is Not Displayed at Debugger Startup (Target Not Connected) Table 5.3 Checkpoints of errors when starting up the emulator debugger (target not connected) Error Checkpoint ERROR 16005: (1) Check the connection between the PC4701 and host machine. Can't connect with the target. See the PC4701 User's Manual. (2) Check that the PC4701 is powered on. See the PC4701 User's Manual.
M306H5T3-RPD-E User’s Manual 6. Maintenance and Guarantee 6. Maintenance and Guarantee This chapter describes how to maintenance, repair provisions and how to request for repair. 6.1 User Registration When you purchase our product, be sure register as a user. For user registration, refer to “User registration” (page 12) of this user's manual. 6.2 Maintenance (1) If dust or dirt collects on any equipment of your emulation system, wipe it off with a dry soft cloth.
M306H5T3-RPD-E User’s Manual 6. Maintenance and Guarantee 6.5 How to Make Request for Repair If your product is found faulty, follow the procedure below to send your product for repair. Customer Fill in the Repair Request Sheet included with this product, then send it along with this product for repair to your local distributor. Make sure that information in the Repair Request Sheet is written in as much detail as possible to facilitate repair.
Emulation Pod M306H5 for M16C/6H Group M306H5T3-RPD-E User’s Manual Publication Date: Dec. 16, 2004 Published by: Edited by: Rev.1.00 Sales Strategic Planning Div. Renesas Technology Corp . Microcomputer Tool Development Department Renesas Solutions Corp. © 2004. Renesas Technology Corp. and Renesas Solutions Corp., All rights reserved. Printed in Japan.
M306H5T3-RPD-E User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10J0866-0100Z
