Datasheet

Rev.6.00 Oct.28.2004 page 758 of 1016
REJ09B0138-0600H
Item Symbol Min Typ Max Unit Test Conditions
Current
dissipation*
2
Normal
operation
I
CC
*
4
—32
(3.3 V)
80 mA f = 13 MHz
Sleep mode — 22
(3.3 V)
55 mA f = 13 MHz
Standby — 0.01 5.0 µAT
a
≤ 50°C
mode*
3
— — 20 50°C < T
a
Flash memory
programming/
erasing
—42
(3.3 V)
80 mA 0°C ≤ T
a
≤ 75°C
f = 13 MHz
Analog power
supply current
During A/D
and D/A
conversion
Al
CC
— 0.3
(3.3 V)
2.0 mA
Idle — 0.01 5.0 µA
Reference
current
During A/D
and D/A
conversion
Al
CC
— 1.6
(3.3 V)
3.0 mA
Idle — 0.01 5.0 µA
RAM standby voltage V
RAM
2.0 — — V
Notes: 1. If the A/D and D/A converters are not used, do not leave the AV
CC
, AV
SS
, and V
ref
pins open.
Connect AV
CC
and V
ref
to V
CC
, and connect AV
SS
to V
SS
.
2. Current dissipation values are for V
IH
min = V
CC
–0.5 V and V
IL
max = 0.5 V with all output pins unloaded and the
on-chip pull-up transistors in the off state.
3. The values are for V
RAM
≤ V
CC
< 3.0 V, V
IH
min = V
CC
× 0.9, and V
IL
max = 0.3 V.
4. I
CC
depends on V
CC
and f as follows:
I
CC
max = 1.0 (mA) + 1.1 (mA/(MHz × V)) × V
CC
× f [normal mode]
I
CC
max = 1.0 (mA) + 0.75 (mA/(MHz × V)) × V
CC
× f [sleep mode]
Table 22-35 Permissible Output Currents
Conditions: V
CC
= 3.0 to 5.5 V, AV
CC
= 3.0 to 5.5 V, V
ref
= 3.0 V to AV
CC
, V
SS
= AV
SS
= 0 V,
T
a
= –20 to +75°C (regular specifications), T
a
= –40 to +85°C (wide-range specifications)
Item Symbol Min Typ Max Unit
Permissible output Ports 1, A to C I
OL
——10mA
low current (per pin)
Other output pins — — 2.0 mA
Permissible output
low current (total)
Total of 32 pins
including ports 1
and A to C
∑ I
OL
——80mA
Total of all output
pins, including the
above
— — 120 mA
Permissible output
high current (per pin)
All output pins –I
OH
— — 2.0 mA
Permissible output
high current (total)
Total of all output
pins
∑ –I
OH
——40mA
Notes: 1. To protect chip reliability, do not exceed the output current values in table 22-35.
2. When driving a darlington pair or LED directly, always insert a current-limiting resistor in the output line, as show
in figures 22-65 and 22-66.