Users Manual

R01UH0823EJ0110 Rev.1.10 Page 1239 of 1852
Nov 30, 2020
RX23W Group 36. CAN Module (RSCAN)
36.2.45 Transmit/Receive FIFO Control Register 0L (CFCCL0)
CFE Bit (Transmit/Receive FIFO Buffer Enable)
Setting this bit to 1 makes transmit/receive FIFO buffers available.
When this bit is set to 0 in transmit mode, if a message in the transmit/receive FIFO buffer is being transmitted or to be
transmitted next, the transmit/receive FIFO buffer becomes empty after completion of transmission, CAN bus error
detection, or arbitration lost. In other cases or in receive mode, the transmit/receive FIFO buffer becomes empty
immediately.
Address(es): RSCAN0.CFCCL0 000A 8350h
b15b14b13b12b11b10b9b8b7b6b5b4b3b2b1b0
CFIGCV[2:0] CFIM— CFDC[2:0] —————CFTXIE
CFRXI
E
CFE
Value after reset:
0000000000000000
Bit Symbol Bit Name Description R/W
b0 CFE Transmit/Receive FIFO Buffer
Enable
0: No transmit/receive FIFO buffer is used.
1: Transmit/receive FIFO buffers are used.
R/W
b1 CFRXIE Transmit/Receive FIFO Receive
Interrupt Enable
0: Transmit/receive FIFO receive interrupt is disabled.
1: Transmit/receive FIFO receive interrupt is enabled.
R/W
b2 CFTXIE Transmit/Receive FIFO
Transmit Interrupt Enable
0: Transmit/receive FIFO transmit interrupt is disabled.
1: Transmit/receive FIFO transmit interrupt is enabled.
R/W
b7 to b3 — Reserved These bits are read as 0. The write value should be 0. R/W
b10 to b8 CFDC[2:0] Transmit/Receive FIFO Buffer
Depth Configuration
b10 b8
0 0 0: 0 messages
0 0 1: 4 messages
0 1 0: 8 messages
0 1 1: 16 messages
1 0 0: Setting prohibited
1 0 1: Setting prohibited
1 1 0: Setting prohibited
1 1 1: Setting prohibited
R/W
b11 — Reserved This bit is read as 0. The write value should be 0. R/W
b12 CFIM Transmit/Receive FIFO Interrupt
Source Select
0:
• Receive mode
When the number of received messages has met the
condition set by the CFIGCV[2:0] bits, a FIFO receive
interrupt request is generated.
• Transmit mode
When the buffer becomes empty upon completion of
message transmission, a FIFO transmit interrupt request
is generated.
1:
• Receive mode
A FIFO receive interrupt request is generated each time a
message has been received.
• Transmit mode
A FIFO transmit interrupt request is generated each time a
message has been transmitted.
R/W
b15 to b13 CFIGCV[2:0] Transmit/Receive FIFO Receive
Interrupt Request Timing Select
b15 b13
0 0 0: When FIFO is 1/8 full.
0 0 1: When FIFO is 2/8 full.
0 1 0: When FIFO is 3/8 full.
0 1 1: When FIFO is 4/8 full.
1 0 0: When FIFO is 5/8 full.
1 0 1: When FIFO is 6/8 full.
1 1 0: When FIFO is 7/8 full.
1 1 1: When FIFO is full.
R/W