WIND DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle Key/radio frequency remote control: general information, use, deadlocking. . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking of opening elements when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (1/2) B A 1 3 3 2 2 1 4 Key, radio frequency remote control A or B 1 Locking the doors and luggage compartment lid. 2 Unlocking the doors and luggage compartment lid. 4 Locking/unlocking the key insert for remote control B. To release insert 3 from its housing, press button 4; it will come out automatically. To reinsert it in its housing, press button 4 and guide insert 3 into the storage position.
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the environment: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control. Note: on certain vehicles, if a door is not opened within approximately 2 minutes of the door being unlocked by remote control, the doors will lock again automatically.
KEY/RADIO FREQUENCY REMOTE CONTROL: use Remote controls A and B are used to lock or unlock the doors. They are powered by a battery which must be replaced (refer to the information on the “Key/radio frequency remote control: batteries” in Section 5). Locking the doors B A 2 1 2 1 Pressing button 1 locks the doors and tailgate. The side indicator lights and hazard warning lights flash twice to indicate that the doors have been locked.
DEADLOCKING 1 1 Deadlocking of the doors and luggage compartment lid To activate deadlocking This allows you to lock the doors and tailgate and to prevent the doors from being opened with the interior handles (by breaking the window and then trying to open the doors from the inside). The hazard warning lights and indicator lights flash five times to indicate that the doors have locked. (for some countries) Press button 1 twice in quick succession.
opening and closing the doors (1/2) As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. 1 2 4 3 Opening from the inside Pull handle 1. Closing from the inside Depending on the vehicle, pull handle 2 or 3. 5 Opening manually from the outside Using the key, unlock left-hand door lock 4. Place your hand under handle 5. Lift the handle and then pull the door towards you.
opening and closing the doors (2/2) 6 7 In the event of a fault with the electric windows: – The window does not lower when the door is opened. If this happens, to close the door, proceed as described in the section entitled “In the event of a battery fault”. Do not close the door by holding the window. zone 7. Make sure you do not place your fingers too high up in Risk of injury. – The window does lower when the door is opened but does not close when the door is closed.
LOCKING/UNLOCKING THE DOORS (1/2) 1 Doors and tailgate status indicator light With the ignition on, the indicator light integrated in button 1 informs you of the status of the doors and luggage compartment lid: – the indicator light is on when the doors/tailgate are locked; – when the doors are unlocked (or not properly closed) the indicator light is off.
LOCKING/UNLOCKING THE DOORS (2/2) 1 2 Locking the doors and tailgate Using the interior door locking/unlocking control. With the engine off and the driver’s door open, switch on the ignition and switch it off again. Press button 1 for more than five seconds, then get out of the vehicle with the remote control with you and close the driver’s door. Manual control Using the key Lock or unlock the doors on the driver’s side by inserting the key fully into lock 2, then turning it.
AUTOMATIC LOCKING WHEN DRIVING You must first decide if you want to activate this function. To activate With the ignition on, press central door locking button 1 for about five seconds, until a double beep is heard. The door can be unlocked: – by opening a door when stationary. 1 – by pressing door unlocking button 1. To deactivate With the ignition on, press central door locking button 1 for about five seconds, until a double beep is heard.
FRONT SEATS 4 1 3 2 To move the seat forwards or back Lift handle 1 to release. Release the handle once the seat is in the correct position and ensure that the seat is locked. To raise or lower the seat base Depending on the vehicle, lift handle 2. Release the handle once the seat is in the correct position and ensure that the seat is locked. Heated seats (depending on the vehicle) With the ignition on, press switch 3. The integrated indicator comes on.
Seat belts (1/3) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Incorrectly adjusted or twisted seat belts may cause injuries in the event of an accident. Use one seat belt per person, whether child or adult.
Seat belts (2/3) ß Driver seat belt reminder warning light This lights up if the driver’s seat belt is not fastened and, when the vehicle reaches a speed of approximately 6 mph (10 km/h), it flashes and a beep sounds for approximately 2 minutes before the light returns to being continuously lit. 5 3 4 5 Locking Unlocking Press button 4 on buckle 5 and the seat belt will be rewound by the inertia reel. Guide the buckle to help the operation.
Seat belts (3/3) – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For special operations (e.g. fitting child seats) contact an approved Dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident. – Never wear the shoulder strap under your arm or behind your back.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) Depending on the vehicle, they are composed of: – Have the entire restraint system checked following an accident. – seat belt pretensioners; – chest-level load limiters; – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – air bags for driver and front passenger.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Air bags for driver and front passenger Fitted to the driver and passenger side. Depending on the vehicle, the presence of this equipment is indicated by the word “air bag” on the steering wheel and dashboard (air bag zone A) and a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Side protection devices Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Warnings concerning the side air bag Depending on the vehicle, a marking on the windscreen informs you of the presence of additional means of restraint (air bags, pretensioners, etc.) in the passenger compartment.
Additional methods of restraint All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. 1 The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: Choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.22 Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
child safety: mounting a child seat Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat. Check that the seat is correctly held by moving it from side to side and back to front: the seat should remain firmly fixed.
Child safety: fitting a child seat (1/3) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. In the front seat The laws concerning children travelling in the front passenger seat differ in every country.
Child safety: fitting a child seat (2/3) Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. ² seats.
Child safety: fitting a child seat (3/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: deactivating/activating the front passenger air bag (1/3) DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered.
child safety: deactivating/activating the front passenger air bag (2/3) A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
child safety: deactivating/activating the front passenger air bag (3/3) 1 2 Activating the front passenger air bags You should reactivate the air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact. To reactivate the air bags: when the vehicle is stationary, push and turn lock 1 to the ON position. With the ignition on, you must ensure that warning light 2 is off.
Driving position: left-hand drive (1/2) 1 2 3 4 5 22 21 20 19 18 6 7 8 13 12 11 10 14 23 1.
Driving position: left-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 7 Centre air vents. 16 H andbrake. 2 Stalk for: 8 Location for passenger air bag. 17 C ruise control/speed limiter control. – direction indicator lights, 9 Side air vent. 18 H azard warning lights switch. – exterior lights, 10 Storage compartment. – front fog lights, 11 Heating and ventilation controls.
Driving position: right-hand drive (1/2) 1 2 22 23 3 4 21 20 17 15 16 1.
Driving position: right-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 7 Instrument panel. 2 Location for passenger air bag. 8 – Windscreen wash/wipe stalk. 3 Centre air vents.
Warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. L A Low fuel level warning light This comes on when the ignition is switched on and goes out after a few seconds. If it comes on when driving accompanied by a beep, fill up with fuel as soon as possible. å Air bag warning light ? Gear change indicator light This light comes on to signal that an upshift is necessary.
Warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. k á g f c b Dipped beam headlight telltale Main beam headlight tell-tale light Front fog light tell-tale light 2 Door status warning light It lights up when the ignition is switched on and a door is open or not properly closed. Δ Speed limiter and cruise control indicator lights Rear fog light tell-tale light See the information on the “Speed limiter” and “Cruise control” in Section 2.
Warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ® A It switches off a few seconds after the ignition is switched on, if it does not light up, consult an approved dealer. It may light up at the same time as other warning lights, together with a beep. It indicates that it is essential to stop immediately (as soon as traffic conditions allow). Contact an approved dealer.
Warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ù Electronic Stability Program (ESP) and traction control (ASR) indicator light. There are several reasons why the light may come on: refer to the information on the “Electronic stability program: ESP” and “traction control system: ASR” in Section 2.
Displays and indicators (1/2) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. 1 Speedometer 1 (km or miles per hour). Overspeed buzzer Depending on the vehicle, a beep sounds for 10 seconds approximately every 40 seconds as long as the vehicle is travelling at over 72 miles per hour (120 km/h). Note: depending on the vehicle, the desired speed may be programmed; consult an approved Dealer. 1.
Displays and indicators (2/2) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Coolant temperature indicator 4 In normal use, the needle should be positioned before zone A. Under “intensive” operating conditions, the needle may approach this zone. This is not serious unless the ® warning light comes on, accompanied by a message on the instrument panel and a beep. 3 4 5 A Fuel gauge 3 Information display 5 The needle shows the fuel level.
TRIP COMPUTER: general information Selection key 1 on display A Press button 1 to repeatedly to scroll through the following information: a) total mileage and trip mileage recorder; A 1 Trip computer and warning system A General reset and trip mileage recorder reset key 1 This includes the following functions: Press and hold button 1 to reset the trip mileage recorder. The display must be set to “Trip mileage recorder”.
TRIP COMPUTER: trip settings (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections 37360 KM 7080 KM FUEL USED 26.0 L Interpreting the display selected a) Total mileage and trip mileage recorder b) Trip settings Fuel consumed since the last reset. AVERAGE 7.3 L/100 Average fuel consumption since the last reset. CURRENT 8.
TRIP COMPUTER: trip settings (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections RANGE 322 KM Interpreting the display selected Estimated range with remaining fuel This range takes into account the average fuel consumption since the last time the reset button was pressed. The value is displayed after driving 400 metres.
TRIP COMPUTER: trip settings (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
TRIP COMPUTER: trip settings (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections BRIGHTNESS Interpreting the display selected d) Dashboard and instrument panel brightness management. SPEED LIMITER 70 KM/H CRUISE CONTROL e) Cruise control/speed limiter programmed speed. Refer to the information on the “Cruise control/speed limiter” in Section 2.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages “ESP OFF” “AUTO LIGHTS DEACTIVATED” Interpretation of messages Indicates that you have deactivated the ASR function. Indicates that the automatic lights function is deactivated. 1.
TRIP COMPUTER: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given on the following pages.
TRIP COMPUTER : warning messages These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Steering wheel/power-assisted steering Power-assisted steering Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 Operating faults The steering may become stiff when driving or when the steering wheel is turned repeatedly. This is due to the power assistance overheating. In this case, it must be allowed to cool down.
Clock and exterior temperature Resetting the clock 1 A 2 With the ignition on, press button: 1 for the hours; 2 for the minutes. Note: for vehicles not fitted with buttons 1 and 2, refer to the instructions for the specific equipment (radio, etc.) to discover the special features. External temperature indicator Special note: When the external temperature is between –3°C and +3°C, the °C characters flash (indicates risk of ice formation).
Rear view mirrors Heated door mirrors (depending on vehicle) A B C 1 D The door mirrors are de-iced when the rear screen demisting/de-icing is active. E 2 Door mirrors with electrical adjustment: With the ignition on, move button 1: – position C to adjust the left-hand door mirror; – position E to adjust the right-hand door mirror; D is the inactive position. Interior rear view mirror The door mirror on the driver’s side has two clearly defined zones.
AUDIBLE AND VISUAL SIGNALS Horn 2 Press the end of the stalk 1. 1 0 Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position in which the stalk may be held when changing lanes. When the stalk is released, it automatically returns to 0. Headlight flasher Pull stalk 1 towards you to flash the headlights.
Exterior lighting and signals (1/2) 1 2 A á Main beam headlights e Switching off the lights With the dipped headlights lit, pull stalk A towards you. An indicator light on the instrument panel will come on. To return to the dipped headlights position, pull stalk A towards you again. position. Return the stalk to its original Lights-on warning buzzer u Side lights Turn end 1 of stalk A until the symbol is opposite mark 2. The instrument panel will light up.
Exterior lighting and signals (2/2) f 1 A 3 Rear fog lights Turn centre ring 3 on stalk A until the symbol faces mark 4, then release it. Operation of the fog lights depends on the exterior lighting selected, and an indicator light will light up on the instrument panel. 4 To avoid inconveniencing other road users, remember to switch off the rear fog light when it is no longer needed.
SCREEN WASHER/WIPER (1/2) 1 2 With the engine running, move stalk 1: A park 1 D Vehicles with automatic wiper function B automatic wiper function A B C When this position is selected, the system detects the presence of water on the windscreen and triggers wiping at a suitable wiping speed. It is possible to change the time between sweeps by turning ring 2.
SCREEN WASHER/WIPER (2/2) 1 1 In snowy or icy conditions, make sure the wiper blades are not stuck by ice. Keep an eye on the condition of the blades. Replace the wiper blades as soon as they begin to lose efficiency (approximately once a year). Windscreen washer With the ignition on, pull stalk 1 towards you. A short pull triggers one sweep cycle of the wiper. A longer pull triggers three sweeps followed by a final sweep after several seconds. Check the condition of the wiper blades.
FUEL TANK (1/2) A 1 2 Fuel grade Filling with fuel Use a high grade fuel with the appropriate octane rating as defined by the particular standards in force in your country. Using leaded petrol will damage the antipollution system and may lead to a loss of warranty. It is essential to use unleaded petrol. The octane rating (RON) must conform with the specifications given on the label inside fuel filler flap A. Refer to the information on “Engine specifications” in Section 6.
FUEL TANK (2/2) Do not mix even small amounts of petrol (unleaded or E85) with diesel. Do not use ethanol-based fuel if your vehicle is not compatible with this fuel. Do not add additive to the fuel – otherwise you risk damaging the engine.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting/stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN/ignition switch Up to 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm. “Ignition” position M The ignition is on and the engine can be started. You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km). “Start” position D If the engine fails to start at the first attempt, turn the key back before activating the starter again. Release the key as soon as the engine starts.
Starting/STOPPING THE ENGINE Stopping the engine With the engine idling, turn the key back to “Stop” position St. Driver’s responsibility Never leave your vehicle with the key or remote control inside the vehicle and never leave a child (or a pet) unsupervised, even for a short while. Starting the engine Engine warm or cold: – Turn the ignition key to “Start” position D without accelerating; – release the key as soon as the engine starts.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
Gear lever/Handbrake Handbrake 1 1 To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. To apply: 3 Pull the lever 2 upwards and make sure the vehicle is immobilised. 2 Gear lever Selecting reverse gear With the vehicle stationary, move the gear lever into neutral then into reverse. Follow the grid shown on knob 1. The reversing lights will come on as soon as reverse gear is selected (with the ignition on).
ADVICE: antipollution, fuel economy and driving (1/3) By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is maintained and used correctly.
ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Avoid sudden acceleration. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal. – Double declutching and accelerating before switching off are unnecessary in modern vehicles.
ADVICE: antipollution, fuel economy and driving (3/3) – For vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in city conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and therefore helping to preserve the environment: Drive with the air vents open and the windows closed.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
Driver correction devices/aids (1/3) Depending on the vehicle, this is composed of: – the (ABS) (anti-lock braking system); – the electronic stability program (ESP) with understeer control and traction control (ASR); – emergency brake assist. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
Driver correction devices/aids (2/3) 1 Electronic stability program ESP Traction control (ASR) This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). This system helps to limit wheelspin of the drive wheels and to control the vehicle when pulling away accelerating or decelerating. Operating principle A sensor in the steering wheel detects the direction selected by the driver.
Driver correction devices/aids (3/3) Emergency brake assist This is an additional system to ABS which helps reduce vehicle stopping distances. 2 1 Operating principle The system detects an emergency braking situation. In this case, the braking assistance immediately develops maximum power and may trigger ABS regulation. ABS braking is maintained as long as the brake pedal is not released.
Cruise control - speed limiter: limiter function (1/3) 1 2 3 4 5 6 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. Controls 1 Main “On/Off” switch. 2 Limit speed activation, storage and increase switch (+). 3 Limit speed activation, storage and decrease switch (-). 4 Switch the function to standby, with limit speed stored (O). 5 Stored limit speed activation, storage and recall (R).
Cruise control - speed limiter: limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by repeatedly pressing: It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the kickdown point). – Switch 2 (+) to increase the speed; 2 3 – Switch 3 (-) to decrease the speed. Whilst the speed is being exceeded, the limit speed displayed on the instrument panel flashes.
Cruise control - speed limiter: limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 5 (R). 2 3 4 1 5 Putting the function on standby Switching off the function The speed limiter function is interrupted when you press switch 1. In this case, the speed is no longer memorised. The orange indicator light on the instrument panel goes out, confirming that the function is deactivated.
Cruise control - speed limiter: cruise control function (1/4) 1 2 3 4 5 This function is an additional driving aid. However, the function does not take the place of the driver. The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h).
Cruise control - speed limiter: cruise control function (2/4) 1 2 3 6 7 Switching on Press switch 1 on the side showing . Warning light 6 comes on, lit green, and the message “CRUISE CONTROL” appears on instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to memorise a cruising speed.
Cruise control - speed limiter: cruise control function (3/4) Exceeding the cruising speed 2 3 The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator pedal: after a few seconds, the vehicle will automatically return to its set cruising speed.
Cruise control - speed limiter: cruise control function (4/4) Recalling the cruising speed If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). 2 3 4 5 1 With a vehicle speed above 20 mph (30 km/h), press switch 5 (R). Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate more rapidly to reach this threshold.
2.
Section 3: Your comfort Rotating hard roof. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning/heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . .
Rotating HARD ROOF: conditions of use Conditions of use Immobilise the vehicle on a flat, level surface (never with the wheel on the pavement). Apply the handbrake. Temperature above -10°C. A Perform the operation with the engine running if possible (risk of discharging the battery). Risk of damage to the roof and roof cover. To prevent the system from overheating, it cuts out automatically. It becomes operational again after a maximum of 30 minutes.
Rotating HARD ROOF: opening/closing Before opening/closing the roof Make sure there are no objects in the way of the roof’s operating area. Make sure that there are no objects resting on the roof or roof cover. Make sure that the luggage compartment lid is properly closed. 1 2 Opening the roof Unlock the roof by pulling and turning control 1 clockwise. Please note: only unlocking is manual – do not lift up the roof. Push switch 2 down and hold it until the roof is fully open.
Rotating HARD ROOF: operating fault (1/2) A 1 The roof unlocks but does not open 2 Remove plastic cover 2 to access the screw. Check that the luggage compartment lid is properly closed. Restart the operation: lock then unlock the roof without pushing it upwards. To avoid all risk of injury, ensure that nobody is in the proximity of the moving parts. Repair procedure If there is a system fault, you can close the rotating hard roof. To do this, open the roof cover manually.
Rotating HARD ROOF: operating fault (2/2) B 3 2 Close the roof again manually (movement B), making sure that there is no contact with the roof cover. Engage plastic cover 2 in its housing. Clip on the logo. Lower the roof cover using the emergency key to turn the screw anticlockwise until the roof cover closes (point of resistance). Pull and turn control 3 anticlockwise to lock the roof. Consult an approved dealer.
air vents: air outlets (1/2) 2 3 4 1 5 1 left-hand side air vent 2 windscreen demister outlets 3 centre air vents 4 right-hand side air vent 5 passenger footwell heater outlets 6 air conditioning control panel. 3.
air vents: air outlets (2/2) To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. 1 Side vent 1 To open, press on the air vent. Turn the vent to position it. Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). There is a risk of damage or of fire. 3.
Manual air conditioning/heating system (1/4) A B C D E F Distribution of air in the passenger compartment Turn control A. W Close the dashboard vents for more effective demisting. All the air flow is directed to the windscreen demisting vents. i The air flow is distributed between the air vents, the windscreen demisting vents and the footwells. F Controls (depending on the vehicle) A Adjusting the distribution of air in the passenger compartment.
Manual air conditioning/heating system (2/4) B Adjusting the ventilation speed C Turn control C from 0 to 4. The passenger compartment is ventilated by blown air. The blower determines how much air enters but vehicle speed has a slight effect on this. The further the control is positioned to the right, the greater the amount of air blown into the passenger compartment. G J The air flow is directed towards the dashboard vents and the footwells. All the air flow is directed to the dashboard vents.
Manual air conditioning/heating system (3/4) D Prolonged use of this position (isolation mode) may mist up the windows slightly or cause odours due to the air not being renewed. It is therefore advisable to return to normal operation (external air) by pressing control D when you have passed through the polluted area. Air recirculation operation (isolation of the passenger compartment) Turn control D towards air recirculation symbol â.
Manual air conditioning/heating system (4/4) C Air conditioning control The air conditioning is switched on (indicator light on) or off (indicator light off) using button E. The system cannot be switched on if control C is set to 0. The air conditioning system is used for: E Use the air recirculation function to lower the temperature as quickly as possible to the required level. Switch off the air recirculation function once a comfortable level has been reached.
AUTOMATIC CLIMATE CONTROL (1/6) 1 2 3 4 5 6 7 8 Information and advice for use Refer to information on “Air conditioning: information and advice on use”. 14 13 12 11 10 9 Controls 6 and 8 Adjusting the ventilation speed. 1 “Clear view” button for demisting and de-icing the windows and/or heated door mirrors. 7 and 9 Passenger compartment air distribution adjustment. (depending on vehicle) 3 Air conditioning on/off button. 4 Starting automatic mode. 5 Display.
AUTOMATIC CLIMATE CONTROL (2/6) 4 5 Only the temperature and the AUTO symbol are displayed Functions managed in automatic mode are not displayed. – press button 10 to increase the temperature; – press button 11 to decrease the temperature. 11 Automatic mode Press button 4. AUTO lights up on display 5. In most cases, the automatic climate control system ensures a comfortable temperature in the passenger compartment, while maintaining good visibility and optimising fuel consumption.
AUTOMATIC CLIMATE CONTROL (3/6) Adjusting automatic mode The system normally operates in automatic mode but you can alter the standard settings used by the system (air distribution, etc.). These options are explained on the following pages. The displayed temperature values show a comfort level.
AUTOMATIC CLIMATE CONTROL (4/6) 4 5 6 8 ô ö F The air flow is directed mainly to the dashboard air vents. The air flow is directed towards all the air vents and the passenger footwells. Distribution of air in the passenger compartment There are five possible combinations for air distribution, which may be selected by pressing buttons 6 and 8 repeatedly. The arrows on display 4 indicate the setting selected: õ ÷ The air flow is directed mainly towards the footwells.
AUTOMATIC CLIMATE CONTROL (5/6) 3 4 5 6 8 Rear screen and/or door mirror de-icing/demisting. Press button 12; indicator light 13 comes on. This function allows electric demisting of the rear screen and/or the electric heated door mirrors, depending on the vehicle. To exit this function, press button 12 again. Demisting automatically stops by default.
AUTOMATIC CLIMATE CONTROL (6/6) 1 2 4 5 6 Air recirculation Pressing button 14 activates air recirculation (the symbol lights up on the display). During recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle. 14 Air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.). 13 12 Clear View function Press button 1; indicator lights 2 and 13 come on. AUTO goes out on display 5.
AIR CONDITIONING: information and advice on use Operating faults Fuel consumption You will normally notice an increase in fuel consumption (especially when driving in town) when the air conditioning is operating. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and therefore helping to preserve the environment: Drive with the air vents open and the windows closed.
Electric windows Operation With the ignition switched on, press the switch for the relevant window upwards to raise it to the desired height. Operating faults 1 2 The system has to be reinitialised: Press the switch for the window concerned downwards to lower it to the desired height. With the door closed and the ignition switched on, – Raise the window fully and keep the button pressed for 2 seconds after it has stopped moving.
Interior lighting/SUN VISOR Luggage compartment light The light comes on when the luggage compartment is opened. 1 2 Courtesy light Tilt switch 1 to move it to the position for: – continuous lighting; – intermittent lighting, which comes on when a door is opened. It goes out when the doors concerned are properly closed; – immediate switching off. Unlocking the vehicle or opening the doors switches on the timed courtesy lights. 3.
Passenger compartment storage space and fittings (1/2) 2 1 Door pockets 1 These can be used to hold cups or the ashtray. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of burning if hot liquid escapes.
Passenger compartment storage space and fittings (2/2) 3 Passenger storage compartment Pull handle 3 to open it. This compartment can be used to hold a pencil. 4 Rear storage compartment 4 To access the storage compartment, move the seat forwards and tilt the seatback forwards. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning, braking or in the event of an accident. 3.
Ashtray, accessories socket 1 2 3 Ashtray 1 This is a removable ashtray that can be fitted into the door storage compartments. To open, lift the cover. To empty it, pull the assembly. The ashtray will come out of its housing. If your vehicle does not have an ashtray, you can purchase one from an approved dealer. Accessories socket 2 or 3 (depending on vehicle) It is provided for connecting accessories approved by the Technical Department with a maximum power of 120 Watts (voltage 12 V).
Tailgate 1 To open Press button 1 and lift the tailgate. To close Lower the luggage compartment lid. The luggage compartment lid can only be opened if the rotating hard roof is locked. 3.24 A Storage under the carpet (depending on vehicle) To open, lift luggage compartment carpet A.
Transporting objects in the luggage compartment Transporting objects on the roof and on the roof cover 1 The fitting of roof bars is prohibited on this vehicle. 2 Always position the objects transported so that the largest surface is against the partition. Anchorage points Hooks 2 located on either side of the luggage compartment allow the load to be secured. Reinforcement bars 1 must not be removed. Always position the heaviest items directly on the floor.
multimedia equipment Audio system The presence and location of the equipment described below depends on the vehicle version. 1 Radio; 2 Steering column control; 3 Microphone. 1 Hands-free telephone integrated control On equipped vehicles, use microphone 3 and steering column control 2. 2 To use this equipment, consult the instructions for the equipment which should be kept with the other vehicle documentation.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . topping up/filling. . . . . . . . . . . . . . . . . . .
Bonnet (1/2) 1 To open, pull handle 1. 2 Unlocking the bonnet catch To open, push tab 2 to the left as you open the bonnet. The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling fan can come on at any moment. Risk of injury. 4.2 In the event of even a slight impact involving the radiator grille or bonnet, have the bonnet lock checked by an approved Dealer as soon as possible.
Bonnet (2/2) Closing the bonnet 3 5 4 Before closing the bonnet, make sure that nothing has been left in the engine compartment. To close the bonnet, replace stay 5 in holder 4. Hold the middle of the bonnet and guide it down to 20 cm above the closed position, then release. It will latch automatically under its own weight. Opening the bonnet Lift the bonnet and release stay 5 from its holder 4. For your own safety, it is very important to fix the stay into retainer 3 in the bonnet.
Engine oil level: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
Engine oil level: topping up/filling (1/2) 1 1 2 2 Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. – Unscrew cap 1; – top up the level (as a guide, the capacity between the minimum and maximum reading on dipstick 2 is between 1.
Engine oil level: topping up/filling (2/2)/OIL CHANGE Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change (including oil filter for information). 1.2 TCE engine: 4.2 litres 1.6 16V engine : 4.7 litres Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling fan can come on at any moment.
Levels (1/3) Checking intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system. 1 Coolant Replacement intervals Refer to the Maintenance Service Booklet for your vehicle.
Levels (2/3) 2 Level 2 Topping up It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MIN” warning line. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website.
Levels (3/3)/Filters Liquid Screen wash product (product with antifreeze in winter). Jets 3 Use a tool such as a needle to adjust the height of the windscreen washer jets. Filters The filter elements (air filter, passenger compartment filter, etc.) should be replaced during the maintenance operations carried out on your vehicle. Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle.
Tyre pressure A B A B I The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. B: dimension of the tyres fitted to the vehicle. C: intended driving speed. C D C D H Tyre safety and use of snow chains E F E F E F Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. E F Special note G G: tyre pressure for the emergency spare wheel.
Battery 1 Depending on the vehicle, a system continuously checks the battery charge status. If the level drops, the message “CHARGE BATTERY” is displayed on the instrument panel. In this case, start the engine. The charge status of your battery can decrease especially if you use your vehicle: A 2 3 4 7 6 5 – for short journeys; – for driving in town; – when the temperature drops; – after extended use of consumers (radio etc.) with the engine switched off.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Protection against the effects of corrosive agents Although your vehicle has been treated with very effective anti-corrosion products, it nevertheless remains subject to the effects of different parameters.
Bodywork maintenance (2/2) You should Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Service Booklet. Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
4.
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit (jack, wheelbrace, etc.). . . . . .
Puncture, emergency spare WHEEL A In the event of a puncture, depending on the vehicle, you will have: An emergency spare wheel or tyre inflation kit (refer to the information on the following pages). Emergency spare wheel This is located in the luggage compartment. To access it: – open the luggage compartment lid; – lift luggage compartment carpet A; – unscrew the central mounting; – remove the emergency spare wheel. 5.
TYRE INFLATION KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/3) 2 3 4 5 6 1 7 10 9 8 Depending on the vehicle, in the event of a puncture, use the tyre inflation kit. Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic. 5.
TYRE INFLATION KIT (3/3) 1 10 8 Once the tyre is inflated correctly: – stop using the kit; – slowly unscrew the two inflation end pieces 8 and 10; – screw end piece 10 onto the bottle so that no product escapes; Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.
TOOL KIT/WHEEL TRIM – WHEEL 2 Wheelbrace 1 3 This is used to tighten or release the wheel bolts. Towing hitch 2 Refer to the information on “Towing” in Section 5. Jack 3 When replacing the jack, fold it correctly and position the wheelbrace correctly before replacing it in its position. 1 4 The tool kit is located in the luggage compartment: lift the luggage compartment carpet then unscrew the central mounting. The tools included in the tool kit depend on the vehicle.
Changing a wheel (1/2) 1 Vehicles equipped with jack, wheelbrace and wheel wrench If necessary, remove the wheel trim. 3 Use wheelbrace 1 to slacken off the wheel bolts. Fit it so that you press downwards rather than pulling upwards. Offer up jack 2 horizontally; the jack head must be lined up with sill 3 as close as possible to the wheel concerned. Start cranking the jack up by hand to align the base plate (which should be pushed slightly under the vehicle).
Changing a wheel (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel are aligned with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and lower the jack.
Tyres (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. 2 You must make sure that your tyres conform to local road traffic regulations. 1 When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads.
Tyres (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.
Tyres (3/3) Use in winter Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. Snow or Winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion. Warning: These tyres sometimes have a specific direction of rotation and a maximum speed index which may be lower than the maximum speed of your vehicle.
Headlights: changing bulbs (1/2) 1 3 B 4 5 A 2 Dipped beam A/main beam B headlights Side light Remove cover A or B, disconnect bulb 3 or 4, unlock spring 2 or 5 to remove the bulb. Bulb type: W5W. Do not touch the bulb glass. Hold it by its base. When the bulb has been changed, make sure you refit the cover correctly. Bulb type: H1. It is essential to use anti U.V. 55W bulbs so as not to damage the plastic on the headlights. 6 Pull bulb holder 6. Change the bulb.
Headlights: changing bulbs (2/2) To comply with current legislation, or as a precaution, you can obtain an emergency kit from an approved dealer containing a set of spare bulbs and fuses. 7 Front fog lights 7 Changing a bulb – Unclip the cover; – turn bulb 8 a quarter of a turn and remove it; – disconnect the bulb and change it. Do not touch the bulb glass. Hold it by its base. When the bulb has been changed, make sure you refit the cover correctly. Bulb type: H11 55W.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (1/3) 1 5 2 A 4 3 Undo screws 1. Remove plastic cover A. Undo screw 2. Unclip and detach the rear light cluster from the outside. 3 Side light and fog light Bulb type: P 21/4W. Undo bulb holder a quarter of a turn. 4 Side light Bulb type: P 21/4W. Undo the bulb a quarter of a turn. Replace the bulb. 5 Side light and brake light Bulb type: P 21/5 W. 6 Direction indicator light Bulb type: PY 21 W. The bulbs are under pressure and can break when replaced.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (2/3) 9 8 7 High level brake light 7 Number plate lights 9 Consult an approved Dealer. – Unclip light 9 by pressing tab 8; – remove the light cover to gain access to the bulb. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (3/3) 11 10 Reversing light 10 Side indicator lights 11 – Turn the bulb holder a quarter of a turn and take out the bulb; Unclip indicator light 11 (using a flatblade screwdriver or similar). – disconnect the bulb and change it. Turn the bulb holder one quarter-turn and take out the bulb. Bulb type: P 21 W. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.16 Take care not to scratch the bodywork.
INTERIOR LIGHTS: changing bulbs (1/2) 1 2 Courtesy light Unclip lens 1 in the direction indicated (using a flat-blade screwdriver or similar). Release bulb 2. Note: to remove the defective bulb, you can use a flat-blade screwdriver or similar. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTS: changing bulbs (2/2) 4 5 3 Luggage compartment light 3 Unclip light 3 by pressing the tabs on each side (using a flat-blade screwdriver or similar). Press tab 4 to release the lens and access bulb 5. Bulb type: W5W. Disconnect the light. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/3) 3 1 2 Fuse box Clip 3 If electrical equipment does not work, check the condition of the fuses. Remove the fuse using tweezers 3, located on the back of cover 1 or in glove box 2. Depending on the vehicle, remove flap 1 or the flap located in storage compartment 2. To identify the fuses, refer to the fuse allocation label (shown on the following pages). It is not advisable to use the free fuse locations.
FUSES (2/3) Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL) Numbers Numbers Allocation Numbers Allocation Windscreen wiper. 11 Direction indicator lights/ Diagnostic socket. 19 Location reserved for additional equipment. 3 Power-assisted steering. 12 Power supply/Instrument panel. 20 Front and rear fog lights. Location reserved for additional equipment. 13 Dipped beam headlights. 4 21 Main beam headlights/ Horn. 22 Location reserved for additional equipment.
FUSES (3/3) Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL) Numbers Allocation Numbers Allocation 27 Location reserved for additional equipment. 36 Location reserved for additional equipment. 28 Passenger compartment ventilation. 37 Heated door mirrors. Numbers Allocation 43 Left-hand side light/number plate light. 44 Location reserved for additional equipment. 29 Radio/Passenger compartment electrical unit. 38 Horn. 30 Accessories socket. 39 Rear fog lights.
Battery: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any electrical consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery. The battery charger must be compatible with a battery with nominal voltage of 12 volts. – When charging, stop the charger before connecting or disconnecting the battery. Do not disconnect the battery when the engine is running.
Battery: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. 2 The two batteries must have an identical nominal voltage of 12 volts.
key, radio frequency remote control: battery A 3 1 2 Key, remote controls Special feature of key A Remove screw 3. 1 2 Note: It is not advisable to touch the electrical circuit in the key cover when replacing the battery. Replacing the battery Open the case at slot 1 using a coin, and replace battery 2, observing the polarity shown on the back of the cover. Batteries can be obtained from your approved Dealer. These batteries should have a service life of approximately two years. 5.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Use of transmission/ receiving devices (telephones, CB equipment etc.
WINDSCREEN WIPER BLADES Refitting a windscreen wiper blade 1 To refit the wiper blade, proceed in reverse order to removal. 2 3 Make sure that the blade is correctly locked in position. 4 Replacing windscreen wiper blades 1 – Lift the windscreen wiper arm 3 as far as it will go (the arm does not lift up completely); – press button 2 and slide the wiper blade sideways to release hook 4 on the wiper arm.
Towing: breakdown The steering wheel must be unlocked and the ignition key must be in position M (ignition on) to provide brake lights and hazard warning lights on the towed vehicle. At night the vehicle must have its lights on. 2 1 You must observe the towing regulations which apply in the country in which you are driving. 5 3 Contact an approved dealer. 4 Only use: – At the front, towing hitch 3 (located in the tool kit). – At the rear, towing point 5.
OPERATING FAULTS (1/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO There is no response, the warning lights fail to light up and the starter does not turn. Battery lead disconnected or terminals corroded. Check battery terminals: scrape and clean if oxidised and retighten. Discharged battery.
OPERATING FAULTS (2/7) The starter is activated POSSIBLE CAUSES WHAT TO DO The engine splutters but does start or starts with difficulty when cold. Incorrect starting procedure. or Poor fuel supply or ignition fault. Refer to the section entitled “Starting/ stopping the engine”. If the vehicle will not start, do not keep trying to start it. Consult an approved dealer. Fuel supply cut-off system activated if vehicle has been subjected to severe impact. Consult an approved dealer.
OPERATING FAULTS (3/7) On the road POSSIBLE CAUSES WHAT TO DO – while turning or braking The level is too low. Top up the engine oil (refer to the information on the Engine oil level, topping up/refilling in Section 4). – at idle speed Low oil pressure. Consult the nearest approved Dealer. The oil pressure warning light comes on: – is slow to go out or remains lit on ac- Loss of oil pressure. celeration. Stop the vehicle and contact an approved Dealer. Loss of engine power. Clogged air filter.
operating faults (4/7) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Leave to cool. Faulty power-assisted steering. Consult an approved dealer. Coolant pump: belt stretched or broken. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved Dealer. Coolant leaks. Check the condition of hoses and the tightness of the clips. Check the expansion bottle: it should contain coolant.
OPERATING FAULTS (5/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Bulb blown. Refer to the information on “Headlights: changing bulbs” or “Rear and side lights: changing bulbs” in Section 5. The direction indicators do not work.
OPERATING FAULTS (6/7) Rotating hard roof POSSIBLE CAUSES WHAT TO DO The luggage compartment lid will not open Rotating hard roof not locked. Lock the rotating hard roof; refer to the information on the “Rotating hard roof: opening/closing” in Section 3. The roof will not open or close. Roof opening conditions not fulfilled. Apply the opening conditions (refer to the information on the “Rotating hard roof” in Section 3). Roof fault.
OPERATING FAULTS (7/7) Rotating hard roof The message “ROOF: HANDBOOK” appears. POSSIBLE CAUSES READ The message “CHECK ROOF” appears continually or when the roof’s open/close switch is pressed. 5.34 WHAT TO DO Roof opening fault. Lock the roof then unlock it without lifting it. Exterior temperature too low (below 10°C). The system does not open, to prevent damage. Roof in thermal protection mode (too many successive operations). Allow the system to cool for a few minutes before using it again.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weights. . . . . . . . . . . . . . . . . .
Vehicle identification plates A 1 2 3 4 5 A The information shown on the vehicle identification plate should be quoted on all correspondence or orders. B The presence and location of the information depends on the vehicle. Vehicle identification plate A 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 MMAC (Maximum permissible all-up weight). 6.2 6 7 8 9 10 11 12 13 3 GTW (Gross train weight – vehicle fully loaded, with trailer).
Engine identification plates A 1 2 A 3 Please quote the information on the engine plate or label A in all correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. A 6.
Dimensions (in metres) 0,795 2,368 0,665 1,456 3,828 1,381* 1,436 1,913 * Unladen 6.
Engine specifications Versions 1.2 Tce 1.6 16V Engine type (see engine plate) D4Ft K4M Cubic capacity (cc) 1,149 1,598 Type of fuel Octane Rating Spark plugs It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. If not available, for a limited time only, use unleaded fuel: – with an octane rating of 91 for a label showing 95 or 98; – with an octane rating of 87 for a label showing 91, 95 or 98.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/4) A ABS...............................................................1.35, 2.10 → 2.12 accessories........................................................................ 5.25 accessories socket............................................................. 3.23 additional methods of restraint......................1.15 → 1.17, 1.19 side protection.............................................................. 1.18 to the front seat belts........................................1.15 → 1.
Alphabetical index (2/4) emergency brake assist.........................................2.10 → 2.12 emergency braking.................................................2.10 → 2.12 emergency spare wheel................................................ 5.2, 5.6 engine oil....................................................................4.4 → 4.6 engine oil capacity....................................................... 4.5 – 4.6 engine oil level............................................................4.
Alphabetical index (3/4) L levels: brake fluid....................................................................... 4.8 coolant................................................................... 1.38, 4.7 fuel................................................................................ 1.38 windscreen washer reservoir.......................................... 4.9 lifting the vehicle changing a wheel................................................... 5.7 – 5.8 lighting: exterior.........................
Alphabetical index (4/4) see-me-home lighting......................................................... 1.53 service sheets..........................................................6.8 → 6.13 side indicator lights changing bulbs.............................................................. 5.15 side protection devices....................................................... 1.18 signals and lights..................................................... 1.52 – 1.53 special features of petrol vehicles..............
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
