TWIZY Z.E.
Welcome to your new electric vehicle This driver’s handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle Electric vehicle: introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric vehicle: charging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Key . . . . . . . . . . . . . . . . . . . . . . .
electric vehicle: introduction (1/4) 2 1 3 4 5 1 Charging cord 2 Electric motor 3 Orange electrical power cables 4 Traction battery 5 12 volt battery 1.
Electric vehicle: introduction (2/4) Electric vehicles have specific features. We therefore recommend that you read these instructions describing your electric vehicle carefully. Batteries Your electric vehicle has two types of battery: – a traction battery; – a 12 volt battery. “58 volt” traction battery Special feature This vehicle has been approved for the four-wheel category. It may need to meet special regulations regarding the type of driving licence required, the type of road used, etc.
Electric vehicle: introduction (3/4) A The A symbol denotes the electrical elements of your vehicle which may present health risks. “58 volt” electrical circuit The electrical circuit can be recognised by the orange cables and by the elements signalled using the ṑ symbol. The vehicle drive system in an electric vehicle uses a direct voltage of approximately 58 volts. This system can get hot during and after switching off the ignition.
Electric vehicle: introduction (4/4) Driving When you lift your foot off the accelerator pedal, the motor generates electrical current during deceleration, and this energy is used to recharge the traction battery. Please refer to the information on the “Charge meter” in Section 2. An electric motor generates a greater engine brake than in a petrol or diesel engine vehicle.
Important recommendations Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, burns or electric shock and serious injury. In the event of an accident or impact to the vehicle In the event of an accident or an impact to the underside of the vehicle (e.g.: striking a post, raised kerb or other street furniture), this may damage the electrical circuit or the traction battery. Have the vehicle checked by an authorised dealer.
Electric vehicle: charging (1/5) 1 2 Charging schematic diagram 1 Wall socket or, depending on the vehicle, charging terminal 2 Charging cord If you have any questions regarding the equipment needed for charging, please ask an authorised dealer. 1.
Electric vehicle: charging (2/5) Important recommendations for charging your vehicle Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, burns or electric shock and serious injury.
Electric vehicle: charging (3/5) Avoid charging and parking your vehicle in extreme temperatures (hot or cold). 2 Wear to the charging cord protective sleeve. When the outdoor temperature is lower than approximately -15°C, the traction battery charging time may be longer. Charging may become impossible when the temperature is extremely low. The charging cord must be replaced in the event that the blue protective sleeve is damaged. Please contact an authorised dealer.
Electric vehicle: charging (4/5) 3 8 4 2 5 7 Recharging the traction battery Ignition switched off: – open flap 3; – take out the entire charging cord 2 located in the storage compartment at the front of your vehicle, pulling it by the plug using reasonable force. The maximum length of the charging cord is approximately 3 metres; – plug in the end of the cord to the power supply (domestic plug socket, etc); – make sure that the stretch limiter 8 of the charging cord 2 is not exceeded during charging.
Electric vehicle: charging (5/5) 3 2 Precautions to take when removing from the socket – Unplug the cord from the power supply by pulling out the plug. The instrument panel goes out; – reposition the cord 2 correctly in the front storage compartment. Depending on the vehicle, place the end of the plug in its housing or the cord connector facing down; – close the flap 3.
Key A Replacement, requirements for additional keys Key If you lose your key or require another, you can obtain one exclusively from an authorised dealer. A Coded ignition-starter key, locking/ unlocking storage compartments. The key must not be used for any function other than those described in the handbook (removing the cap from a bottle, etc.). 1.12 Driver’s responsibility Never leave your vehicle with the key inside and never leave a child (or a pet) unsupervised, even for a short while.
Opening and closing the doors 1 Opening from inside or outside Lift handle 1 and pull upwards. Closing Lower the door until it locks into place. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time. They may pose a risk of injury, such as by starting the engine or activating equipment. Risk of serious injury.
ENGINE IMMOBILISER Vehicle protection tell-tale light This prevents the vehicle being driven by anyone not in possession of the vehicle’s coded ignition key. After the ignition has been switched off, warning light 1 flashes and the vehicle is protected. The vehicle is automatically protected after the engine is switched off. Operating fault warning light If the warning light continues to flash or stays lit up permanently following an attempt to start the engine, this indicates a fault in the system.
Front seat Access to the rear seats 2 Lift strap 2 and slide the driver’s seat forwards. To replace the seat in the driving position, pull strap 2 towards the rear of the vehicle until you get to the desired position. 1 To move the seat forwards or back Lift handle 1 to unlock the seat. Release the handle once the seat is in the correct position and ensure that the seat is fully locked into position. Make sure the seat is locked in place.
Seat belts (1/3) For safety reasons, always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of your country. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. 1 1 2 Adjusting your driving position – Sit well back in your seat. This is essential to ensure your back is positioned correctly; – adjust the distance between the seat and the pedals.
Seat belts (2/3) Unfastening 3 5 3 Press button 6 and the seat belt will be rewound by the inertia reel. Guide the belt into position. 6 4 7 4 Locking Adjusting the seat belts Unwind the belt slowly and smoothly and ensure that buckle 5 locks into catch 4 (check that it is locked by pulling on buckle 5). If the belt jams, allow it to return slightly before attempting to unwind it again. Sit with your back firmly against the seatback.
SEAT BELTS (3/3) – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g.: fitting booster seats), please contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident. – Never wear the shoulder strap under your arm or behind your back.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) These are made up of: – a side support belt; – chest force limiters; – the driver’s airbag. These systems are designed to act independently or together when the vehicle is subjected to a frontal impact. Depending on the severity of the impact, the system can trigger: – the seat belt and side support belt locking; – the front airbag. – Have the entire restraint system checked following an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Side support belt Airbag Please see the information on “Seat belts” in Section 1. This is fitted in the front seats. Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. An Airbag marking on the steering wheel informs you of the presence of this equipment.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. Operation This system is only operational when the ignition is switched on.
Additional methods of restraint All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. 1 The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use a booster seat and ensure you use it correctly.
Child safety: General information (2/2) Use Only a booster seat should be used. The level of protection offered by the booster seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a booster seat, check that it complies with the regulations for your country and that it can be fitted in your vehicle.
child safety: attaching a booster seat Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the booster seat manufacturer are respected. Do not use the booster seat if it risks loosening the seat belt restraining it: the base of the booster seat must not rest on the buckle and/or catch of the seat belt.
Child safety: installing a booster seat (1/3) In the rear seat For child safety, move the front seat as far forward as possible to install a booster seat, then move it back as far as it will go, without allowing it to come into contact with the child. Check that the booster seat is resting against the back of the vehicle seat. Check that when installing the booster seat in the vehicle, it is not at risk of coming loose from its base.
Child safety: installing a booster seat (2/3) ² seats. Seat not suitable for fitting child Seat which only allows a standardised “Universal” booster seat to be installed using a seat belt. Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child. They risk serious or even fatal injury. 1.
Child safety: installing a booster seat (3/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Driving position The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 2 3 5 4 7 and 12 door mirrors To adjust the mirrors, press on the mirror. 6 8 Key ignition switch. 9 Handbrake. 10 C ontrols for: – forward gear, – neutral, – reverse. 11 H azard warning lights switch. 12 11 10 9 1 Storage and accessories socket.
Warning lights (1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A u á d ê Side light tell-tale light Main beam headlight tell-tale light Direction indicator lights Engine immobiliser system warning light Refer to the information on the “Engine immobiliser” in Section 1. Vehicle ready for driving warning light Please see the information on “Starting, stopping the engine” in Section 2.
Warning lights (2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. STOP light ® This lights up when the ignition A is switched on and goes out as soon as the engine is started. It lights up at the same time as other warning lights, and is accompanied by a beep. It requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. Contact an approved Dealer.
Warning lights (3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A Low traction battery level warning light This comes on when the traction battery charge level has reached the reserve threshold. Please see the information on “Displays and indicators” in Section 1. Electrotechnical warning light 1 system If it lights up while driving, this means there is an electrotechnical fault in the “58 volt” electrical circuit.
displays and indicators (1/2) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Immobilisation threshold imminent 2 When the battery reaches less than 6% charge, a beep repeats every 20 seconds and warning light Ṏ flashes on and off. Motor performance gradually decreases until the vehicle comes to a stop. Please see the information on “Towing: in the event of energy loss” in Section 5.
displays and indicators (2/2) Forecast range display features 4 – Sporty driving will strongly affect the forecast range value. Once you return to a calmer driving style, you will need to drive for several miles to return to an estimate that is closer to the real situation; – the forecast range displayed after charging the traction battery is calculated based on the power consumption over the last 93 miles (150 kilometres) travelled.
Clock – repeatedly press button 2 as necessary to adjust the hour; 1 2 – press and hold button 2 to confirm the hours. The minute display flashes; – repeatedly press button 2 as necessary to adjust the minutes; – press and hold button 2 to confirm the minutes. With the ignition switched on, the clock is displayed on the instrument panel.
AUDIBLE AND VISUAL SIGNALS Direction indicators 1 0 Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 2 When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is also an intermediate position in which the switch may be held when changing lanes. When the stalk is released, it automatically returns to 0. Horn Press the end of stalk 1.
Horn Electric vehicles are particularly quiet. This system enables you to warn people of your presence – especially pedestrians and cyclists. 1 2 Activating the system With the engine running, turn centre ring 1 on the stalk until the symbol ṫ faces mark 2. Deactivating the system Turn the centre ring 1 to position 0 again. 1.
Exterior lighting and signals A 1 2 A á Main beam headlights e Switching off the lights With the dipped headlights lit, pull stalk A towards you. An indicator light on the instrument panel will come on. To return to the dipped headlights position, pull stalk A towards you again. position. Return the stalk to its original Lights-on warning buzzer u Side lights Turn end 1 of stalk A until the symbol is opposite mark 2. The instrument panel lighting dims.
SCREEN WASHER/WIPER 1 1 D A B C When working on the vehicle, ensure that the windscreen wiper stalk is in position A (off). Risk of injury. Before any action involving the windscreen (washing the vehicle, de-icing, cleaning the windscreen, etc.) return stalk 1 to position A (park). Risk of injury and/or damage. n stalk 1: Windscreen wiper Windscreen washer With the ignition on, move With the ignition on, pull stalk 1 towards you.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Starting, stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handbrake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vehicle range: recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting, stopping the engine “Accessories” position A No power-consuming device will operate when the ignition is switched off. Stopping the engine Bring the key to “Stop” position. Warning light Ṑ goes out. “On” position M The ignition is switched on: Start position D Starting the engine Turn the key to the D position and hold it in this position until you hear a beep. Release the key.
Gear control (1/2) Driving Press switch D, a beep will sound. While driving, press the accelerator pedal to achieve the desired speed. 2 D Hill start N 1 R Display 1 Operation The display 1 on the instrument panel indicates the selection control position 2. – Switch on the ignition; – start the engine; – with your foot on the brake pedal, release the handbrake (refer to the information under “Handbrake” in Section 2). It will now be possible to drive off.
Gear control (2/2) Temporary stop At a standstill and with the engine running, when position D or R is engaged, a beep will sound and warning light Ṑ flashes until one of the following conditions is met: – brake pedal pressed; N – accelerator pedal pressed; – N switch pressed; – the handbrake is secured. 3 Parking the vehicle With the vehicle at a standstill, press switch N. Warning light 3 comes on the instrument panel. Engage the handbrake (please see the “Handbrake” information in Section 2).
Handbrake 3 To apply: Pull lever 1 upwards and make sure the vehicle is immobilised. Warning light 3 D 1 panel. will come on on the instrument 2 Handbrake To release: With the ignition on, pressing on the brake pedal: – lightly pull lever 1 towards you; – press button 2; – fully lower the lever. The handbrake is a vehicle safety measure. It cannot be released unless the ignition is switched on. Special conditions It is not possible to release the handbrake when the 12 volt battery is discharged.
Vehicle range: recommendations (1/2) You have a certain amount of control over your vehicle’s range. A number of factors must be monitored for this: – speed and driving style; – type of road; – tyres; – electrical accessories and equipment; – vehicle loading. Speed and driving style High speeds will reduce your vehicle’s range. A “sporty” driving style reduces your vehicle range: opt for a “lighter” driving style. Drive at a constant speed. Adapt your driving style to avoid excessive energy consumption.
Vehicle range: recommendations (2/2) Use of electrical accessories and equipment In the event of freezing, manually de-ice the windscreen (using a scraper) to reduce usage of the de-icing/demisting function and to save energy. Please see the information on “Deicing, demisting the windscreen” in Section 3. The use of electrical accessories (GPS, phone charger, etc.) reduces vehicle range. Vehicle loading Avoid pointlessly overloading your vehicle. Tyres An under-inflated tyre increases energy consumption.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. Please make your own contribution towards protecting the environment too. Manufacture – Worn parts replaced in the course of routine vehicle maintenance (vehicle battery, etc.) must be disposed of through specialist bodies.
Charge meter/Eco-consumption A Charge meter The charge meter gives the driver a real-time view of the vehicle’s remaining power. Power consumption A The traction battery supplies the electrical energy required for the motor to move the vehicle. B Power recovery B When driving, if you lift your foot off the accelerator pedal, the motor generates electrical current during deceleration, and this energy is used to recharge the traction battery.
2.
Section 3: Your comfort De-icing, demisting the windscreen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Passenger compartment storage space and fittings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 3.3 3.
Windscreen de-icing, demisting 1 2 De-icing or demisting the windscreen With the engine running, turn the end of stalk 1. Warning light 2 lights up on the instrument panel. To exit this function Turn the end of stalk 1. Warning light 2 goes out on the instrument panel. Demisting automatically stops approximately 10 seconds after it is activated. This function enables quick electric deicing/demisting.
Passenger compartment storage/fittings (1/2) Accessories socket 3 2 Located in the storage compartment 1, this is provided for connecting accessories approved by the Technical Department with a maximum power of 65 watts (voltage of 12V). 1 5 4 3 6 Left-hand storage compartment 1 Right-hand storage compartment 4 To open, lift cover 2. To open, lift cover 5. To lock and unlock the storage compartment 4, insert the ignition key in lock 6 and turn it.
Passenger compartment storage/fittings (2/2) A 8 7 Storage 8 Located behind the rear seat back A. To unlock the seat back A, insert the ignition key in lock 7 and turn it. Unclip the seat back A. NB: When replacing, make sure you lock the seat back in place. Lock 7 enables you to lock and unlock the rear passenger seat back. Do not put any object or animal weighing over 10 kg on the rear seat. Risk of serious injury when braking sharply or in an impact. 3.
Section 4: Maintenance Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . brake fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . windscreen washer reservoir. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 volt battery . . . . . . . . . . . . . . . . . . . . . . . . . . .
Levels (1/2) Topping up 1 After any operation on the hydraulic circuit, a specialist must replace the fluid. Only use fluids approved by our Technical Department (and taken from a sealed container). Replacement intervals Refer to the Maintenance Service Booklet for your vehicle. 3 2 Brake fluid level Level 3 It is normal for the level to drop as the linings become worn, but it should never drop below the MIN line.
Levels (2/2) Jet 5 Use a pointed tool to adjust the height of the windscreen washer jets. 4 Windscreen washer reservoir Topping up Open flap 5. Open cap 4 and fill until you see the liquid. Then close the cap. Liquid Screen wash product (product with antifreeze in winter). 4.
12 volt battery (1/3) Replacement As this operation is complex, we advise you to contact an approved Dealer. 1 2 Access Remove screws 2 under the front bonnet and clips 1. Lift up the bonnet. Maintenance Refer to the Maintenance Service Booklet for your vehicle. 3 The charge status of the 12 volt battery 3 can decrease, especially if you use your vehicle: – when the outside temperature drops; – after extended use of energy-consuming devices (lights etc.) with the engine switched off.
12 volt battery (2/3) A 4 5 6 Special procedures may be required to charge some batteries. Contact your approved dealer. 9 8 7 Avoid all risk of sparks which may cause an immediate explosion, and charge the battery in a well-ventilated area. Risk of serious injury. Label A Replacing the 12 volt battery: For your own safety, you must respect the replacement intervals (without exceeding them) as stated in the maintenance document.
12 volt battery (3/3) Recharging the 12 volt battery It is difficult to access the 12 volt battery. It is therefore recommended that you attach the vehicle plug to a power source: energy is supplied to both the 12 volt battery and the traction battery at the same time. Please refer to the information on “Electric vehicle: charging” in Section 1.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Some parts may look different over time (e.g.: bleaching, etc.
Bodywork maintenance (2/2) You should – Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. – Quickly repair, or have repaired, areas where the paint has been damaged, to prevent corrosion spreading. – Remember to visit the body shop periodically if your vehicle has an anti-corrosion warranty. Refer to the Maintenance Service Booklet. – Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and wipe up excess water. Instrument panel glass and door deflector (e.g.: instrument panel, clock, etc.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you have to remove detachable equipment to clean the passenger compartment, make sure you reinstall it properly and attach them using the original parts. With the vehicle stationary, ensure that nothing will impede driving (anything obstructing the pedals, etc.). Washing with a water jet is permitted if you do not wash higher than the driver’s seat.
Section 5: Practical advice Tyres (tyre and wheel safety, use in winter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Headlights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear lights (changing bulbs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indicator lights (changing bulbs). . . . . . . . . . . . . . . . . . . .
Tyres (1/4) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. The front and rear wheels have different dimensions. For safety reasons, it is not permitted to switch the front wheels with the rear wheels. When they need to be replaced, only tyres of the same make, size, type and profile should be used.
Tyres (2/4) Tyre pressures If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.2 to 0.3 bar (or 3 PSI). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. Never deflate a hot tyre. Respect the tyre pressures, checking them at least once a month and before any long journeys. Use in winter The use of snow or winter tyres significantly reduces the vehicle range.
Tyres (3/4) A B C Fitting new tyres Due to the special design of this vehicle, please bear in mind the tyre specifications as indicated: A = Dimension, type and structure. B = Brand C = Commercial name For safety reasons, this operation must be carried out by a specialist.
Tyres (4/4) Front wheels Rear wheels Type of tyres Type of “snow” tyres 125/80 R13 65M 125/80 R13 65T TS800 Conti.eContact ContiWinterContact 145/80 R13 75M 145/80 R13 75T TS800 Conti.eContact ContiWinterContact When they need to be replaced, only tyres of the same make, size, type and profile should be used. Tyres fitted to the vehicle should either be identical to those fitted originally or conform to those recommended by your authorised dealer.
Front headlights: changing bulbs (1/2) 1 3 5 4 2 Front lights – Unclip upper bar 2 of the bonnet before introducing your hand in 1; – unscrew 3 the front lights using standard tools; – pull the headlight towards you as far as it will go. 3 – Turn bulb a quarter of a turn 4; Type of bulbs – and/or undo the bulb 5, then turn the bulb holder a quarter turn. 4 Side light Bulb type: W5W. 5 Dipped beam/main beam headlights Bulb type: H4. Note: the headlight cannot be pulled out completely.
Front headlights: replacing bulbs (2/2) Cleaning the headlights Use a soft cloth. If this does not clean it properly, moisten the cloth with soapy water then rinse off. Finally, carefully dry off with a soft dry cloth. 6 Cleaning products containing alcohol must not be used under any circumstances. Direction indicator lights 6 Please see an authorised dealer.
REAR LIGHTS: changing bulbs (1/2) Refitting To refit, proceed in the reverse order, taking care not to damage the wiring. 2 3 1 Reversing/side and brake lights From inside the vehicle: – unclip covers 1 using a flat-blade screwdriver or similar; – unscrew using a Torx tool. Side light and brake light 2 Bulb type: P21/5W. Reversing indicator light 3 Bulb type: PY21W. From outside the vehicle: – release the light unit by pulling it backwards; – unscrew bulb holder 2 or 3 and replace the bulb.
REAR LIGHTS: changing bulbs (2/2) 4 5 6 Number plate lights 5 Direction indicators 6 – Unclip light 5 by pressing tab 4; Please see an authorised dealer. – remove the light cover to gain access to the bulb. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/2) 1 A Fuse box Tweezers 1 If any electrical component does not work, check the condition of the fuses. Disconnect the fuse using pliers 1. Apply the handbrake and unclip flap A. In accordance with local legislation or as a precautionary measure: Obtain an emergency kit containing a set of spare bulbs and fuses from an approved Dealer. 5.10 Check the fuse in question and replace it, if necessary, by a fuse of the same rating.
FUSES (2/2) Allocation of fuses (the presence of fuses DEPENDS ON THE EQUIPMENT LEVEL OF THE VEHICLE) Symbol Allocation Symbol 60 Circuit breaker Ṍ Ṟ Inverter L U Left-hand dipped beam headlight STOP Allocation Traction battery Brake lights Charger Y Side light, left rear light Á K Light stalk Q Front left headlight Æ Accessories socket Å Airbag ELEC Windscreen de-icing ô Passenger compartment ECU ṡ Power and supply connection î Diagnostics/Radio socket T Right-hand dipp
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory, make sure it is compatible with your vehicle. You can get advice from an authorised dealer. To install an accessory requiring intervention with the vehicle’s 12 V electrical circuit, please follow these instructions: – make sure that the charging cord is unplugged from the power supply; – switch off the ignition; – disconnect the 60A circuit breaker fuse. Risk of serious injury.
WIPER BLADE 1 2 Replacement With the ignition on and the engine stopped: – lift windscreen wiper arm 2 as far as it will go; – pivot blade 1 until it is removed from its hinge. Refitting To refit the wiper blade, clip the blade onto its hinge. Make sure that the blade is correctly locked in position. Check the condition of the wiper blades.
Towing: towing point and choice of towing Choice of towing There are two ways to tow the vehicle, depending on the type of immobilisation. 1 2 Access to the towing point Remove screws 2 under the front bonnet and clips 1. Lift up the bonnet. In the event of an energy fault In the event of a fully discharged traction battery. All types of towing are permitted (please see the information on “Towing: in the event of an energy fault” on the following pages). 3 Only use the front and rear towing points 3.
Towing: in the event of an energy fault 1 Towing in the event of an energy fault In the event of the full discharge of the traction battery, the vehicle can be towed as indicated below, or on a flat surface (please see following pages): – warning light Ṏ flashes on the instrument panel; – battery warning light 1 on the instrument panel is empty. Before towing, insert the key in the switch to unlock the steering column. Turn key to position M.
Towing : breakdown recovery Breakdown recovery Breakdown recovery must be performed on a flat surface under all circumstances except where the vehicle is immobilised following a full discharge of the traction battery. 5.16 Before breakdown recovery, insert the key in the ignition to unlock the steering column. The regulations in force for breakdown recovery must always be observed.
Operating faults (1/3) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. FAULTS POSSIBLE CAUSES WHAT TO DO Impossible to charge the traction battery. No electrical current in domestic sockets or poor connection of cable to domestic socket. Check your installation (circuit breaker, programmer, etc.). Check the connections (power socket, etc.).
OPERATING FAULTS (2/3) Electrical equipment POSSIBLE CAUSES ACTION REQUIRED The wipers do not work. Wiper blade stuck. Free the blade before using the wipers. Broken windscreen wiper fuse. Consult an approved dealer. Motor fault. Consult an approved dealer. Faulty electrical controls. Consult an approved dealer. The wiper does not stop. Direction indicators flashing more Blown bulb. quickly. Replace the bulb. The indicators are not working. Replace the bulb.
OPERATING FAULTS (3/3) Electrical equipment POSSIBLE CAUSES ACTION REQUIRED The headlights are not working. – blown bulb, Replace the bulb. Only one: – disconnected wire or incorrectly- Check and reconnect the wire or the connector. positioned connector, Both: The headlights do not switch off. – faulty earth connection. See above. – if the circuit is fused. Check and replace if necessary. Faulty electrical controls. Consult an approved dealer. Traces of condensation in the lights.
5.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weights. . . . . . . . . . . . . . . . . . . .
Vehicle identification plates A A 1 2 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. Vehicle identification plate A 1 Vehicle type and chassis number. 2 Paint reference. 6.
Engine identification plate/Engine specification 1 A 2 3 A Please quote the information on the engine plate or label A in all correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. Engine specification Engine type 1: 3CG 6.
WEIGHTS (in kg) The weights shown are for a basic vehicle without options: they will vary depending on the equipment level of your vehicle. Contact an authorised dealer. Vehicle type Twizy 45 Twizy Unladen weight excluding traction battery 347 375 Mass in Running Order (MRO) 446 474 Gross Vehicle Weight (GVW) 685 690 Braked Trailer Weight prohibited Unbraked Trailer Weight prohibited Maximum permissible load on roof prohibited 6.
Dimensions (in metres) 0,313 1,686 0,339 1,193 → 1,237 2,337 1,454* * Unladen 1,188 → 1,232 1,381 → 1,396 6.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
Anticorrosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/3) A accessories........................................................................ 5.12 additional methods of restraint...............................1.19 → 1.22 to the front seat belts........................................1.19 → 1.21 to the rear seat belts.........................................1.19 → 1.21 adjusting your driving position............................................ 1.16 air bag....................................................................1.19 → 1.
Alphabetical index (2/3) front lights changing bulbs....................................................... 5.6 – 5.7 front seat adjustment.......................................................... 1.15 front seats adjustment........................................................1.15 → 1.18 with manual controls..................................................... 1.15 fuses........................................................................ 5.10 – 5.11 H handbrake.......................................
Alphabetical index (3/3) S seat belt pretensioners...........................................1.19 → 1.21 front seat belt....................................................1.19 → 1.21 seat belts.......................................................1.16 → 1.22, 1.31 service sheets..........................................................6.7 → 6.12 signals and lights................................................................ 1.38 starting..................................................................
TWIZY Z.E. ( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
