TRAFIC DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving ................................................................... 2 Your comfort . ........................................................ 3 Maintenance .......................................................... 4 Practical advice ..................................................... 5 Technical specifications . ..................................... 6 Alphabetical index .............
TYRE PRESSURES (in bar, when cold) Tyre dimensions (original fittings) 195/65R 16 C 205/65 R 16 C Wheel sizes 215/65 R 16 C 195/75 R 16 C 6 J 16 Front 3.4 3.8 3.1 3.8 Rear 3.7 4.2 3.4 4.2 Emergency spare wheel 3.7 4.2 3.4 4.2 Tyre safety and use of snow chains Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. 0.
Section 1: Getting to know your vehicle Key – Remote control – Deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anti-intrusion alarm. . . . .
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (1/2) B A C 2 3 1 Key A 1 Key for ignition switch, doors and fuel filler cap. 1 5 4 6 Radio frequency remote control B Radio frequency remote control C 2 Unlocking the front doors or all doors and tailgate. 3 Locking the front doors or all doors and tailgate. 4 Locking/unlocking the tailgate and the sliding side doors. 5 Locking all doors and tailgate. 6 Unlocking the front doors or all doors and tailgate.
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (2/2) The remote control operating range This varies according to the environment: therefore take care when handling the remote control that you do not inadvertently lock or unlock the doors. Note: on certain vehicles, if a door is not opened within approximately 30 seconds of the door being unlocked by remote control, the doors will lock again automatically.
KEY/RADIO FREQUENCY REMOTE CONTROL: use (1/2) Door locking/unlocking B Press the remote control for approximately one second to lock (side E) or unlock (side D). The side indicator lights and hazard warning lights flash twice to indicate that the doors have been locked. D E Remote control B is used to lock or unlock the doors. It is powered by a battery which must be replaced (refer to the information on the “Radio frequency remote control: batteries” in Section 5). 1.
KEY/RADIO FREQUENCY REMOTE CONTROL: use (2/2) Unlocking the doors C 2 1 3 A short press on button 2 unlocks the front doors and, depending on the vehicle, the sliding side doors. Pressing and holding button 2 unlocks all the doors and the tailgate. A short press on button 1 locks/unlocks the tailgate and, depending on the vehicle, the sliding side doors. 1 The hazard warning lights and side indicator lights flash once to indicate that the doors have been unlocked.
DEADLOCKING A A Deadlocking of the doors and tailgate To activate deadlocking, press button A on the remote control unit twice. This allows you to lock the doors and tailgate and to prevent the doors from being unlocked with the interior handles (for example, by breaking the window and then trying to open the door from the inside). The hazard warning lights flash five times to indicate locking.
INTERIOR ELECTRIC DOOR LOCKING CONTROL 1 From inside with the electric central locking 1 0 This enables all the doors to be locked simultaneously. To lock, press the switch on the side with the padlock symbol. Driver’s responsibility Note: the front doors cannot be locked if a door is open. If you decide to keep the doors locked when you are driving, remember that it may be more difficult for those assisting you to gain access to the passenger compartment in the event of an emergency. 1.
AUTOMATIC LOCKING WHEN DRIVING Operating faults You must first decide if you want to activate this function. To activate With the ignition on, press central door locking switch 1 on the locking side (padlock symbol) for approximately 5 seconds, until a beep sounds (unlocking/locking). 1 If you notice that the system is not operating correctly (automatic locking does not take place), first check that all the doors have been properly closed. If they are properly closed, contact an approved dealer.
FRONT DOORS (1/2) Manual locking (depending on vehicle) With the door closed, lock the door by pressing button 3. 3 1 4 2 Opening from the outside Opening from the inside Unlock the driver’s door 2 using the key or, for vehicles fitted with the system, use the remote control system. Pull lever 1 towards you and open the door. Pull lever 4. Closing from the outside Push the door. Lock 2 with the key or using the remote control. Closing from the inside Pull the door until it catches automatically.
FRONT DOORS (2/2) Lights-on warning buzzer If you have left the lights switched on after switching off the ignition, a warning buzzer will sound when a front door is opened (to prevent the battery running down, etc.). Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time.
SLIDING SIDE DOORS (1/2) 2 1 3 4 Opening from the outside Opening from the inside Unlock the front door using the key, or, for vehicles fitted with the system, use the remote control unit. Pull handle 1 towards you and slide the door towards the rear. Pull lever 3 towards the rear and open the sliding door until it locks into position. Closing from the outside Slide the door towards the front of the vehicle, holding door handle 1 until the door is fully closed.
SLIDING SIDE DOORS (2/2) Recommendations concerning the sliding side door Care must be taken when opening or closing the sliding door, as is the case for any of the opening elements on the vehicle: – check that the door will not come into contact with any person, part of the body, animal or object; 5 – use only the handles on the inside and outside of the door to operate it; Child safety – take care when opening and closing the door; To prevent the sliding side door from being opened from the inside
HINGED REAR DOORS (1/3) 1 2 Opening from the outside Unlock the rear door using the key or, for vehicles fitted with the system, use the remote control system. Pull lever 1 towards you and open the door. Press handle 2 and open the second door. If the vehicle is parked on the hard shoulder with tailgate open, the rear lights may be obscured.
HINGED REAR DOORS (2/3) 3 Opening the doors to the maximum position For each door, pull handle 3 to release the door tie-rod 4. Open the door as far as possible. Do not leave the hinged rear doors open in case of strong winds. Risk of injury. 1.14 4 Closing from the outside Return the doors to an almost-closed position and slam them shut. For your safety, check that all the vehicle’s doors are properly closed before starting the engine.
HINGED REAR DOORS (3/3) 6 5 Opening from the inside Closing from the inside Pull handle 5 and open the door. Close the door using handle 6, then close the second door. Move lever 6 and open the second door. For your safety, check that all the vehicle’s doors are properly closed before starting the engine. Do not leave the hinged rear doors open in case of strong winds. Risk of injury. 1.
TAILGATE 1 2 The tailgate locks and unlocks at the same time as the doors. To open Press button 1 and lift the tailgate. 1.16 To close Lower the tailgate, initially using the interior handle 2 to assist you. When the tailgate has been lowered to shoulder height, release handle 2 and finish closing the tailgate by pressing down on the tailgate from the outside.
ANTI-INTRUSION ALARM (1/2) This protects the vehicle by performing the following functions: 1 – volumetric protection of the front passenger compartment using an ultrasound field; – protection of the passenger compartment perimeter; 1 – protection of the rear load area and bonnet; – monitoring in the event of an attempt to start the engine with an incorrect ignition key; – monitoring in the event of siren power supply cut-off.
ANTI-INTRUSION ALARM (2/2) Activating the alarm function The alarm is set when the doors are locked with the remote control. This is signalled by the hazard warning lights flashing twice. When the alarm function is activated, any detection leads to the alarm siren being triggered and the hazard warning lights flashing for around 25 seconds. After approximately 5 seconds, if the detection persists, the system will be triggered again for approximately 25 seconds and then again for approximately 13 minutes.
FRONT SEATS ð With the ignition on, press switch 5 for the seat required and an indicator light will come on. 3 5 1 2 To move forwards or backwards Lift bar 2. Adjust the seat and release the bar. Make sure the seat is correctly locked in position. To adjust the height of the seat Lift handle 1. Release it in the position required. Note: lift yourself out of the seat while you are raising the seat height. To tilt the seatback Move lever 6.
HEADRESTS To put the headrest back in place Insert the rods into the sleeves. 1 Lower the headrest until it locks in position. 13317 1 To raise or lower the headrest Pull the headrest towards you and slide it up or down at the same time. To remove the headrest Raise the headrest until it is at the highest possible setting. Lift up tab 1 and then pull the headrest upwards until it is released. 1.20 The headrest is an important safety component: ensure that it is in place and in the correct position.
Steering wheel/power-assisted steering Power-assisted steering If you have power-assisted steering fitted, do not leave the steering wheel at full lock while stationary as this may damage the pump. 1 Steering wheel Height and reach adjustment. Pull lever 1 and move the steering wheel to the required position. Then, push the lever back fully, beyond the point of resistance to lock the steering wheel. Make sure that the steering wheel is correctly locked.
FRONT SEAT BELTS (1/2) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Seat belts which are incorrectly adjusted or twisted may cause injuries in the event of an accident. Use one seat belt per person, whether child or adult.
FRONT SEAT BELTS (2/2) ç Front seat belt reminder warning light 1 5 This light is lit when the vehicle is started, then, if the driver’s seat belt is not fastened when the vehicle reaches a speed of approximately 10 mph (16 km/h), it flashes and a beep sounds for approximately 90 seconds. 3 5 4 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3).
REAR SEAT BELTS (1/2) 1 2 3 4 4 Rear side seat belts – For the first row of rear seats, you must use seat belts 1; – For the last row of rear seats, you must use seat belts 2. Conditions of use Access to the last row Before using the rear side seat belts, make sure that for each one, fixed buckle 3 is fully clicked into its catch 4. To facilitate access to the last row of seats, detach the seat belt of the second row by unlocking it from its catch 4.
REAR SEAT BELTS (2/2) 5 Centre seat belts Unwind the seat belt slowly until the buckle locks in catch 5. Make sure that the rear bench seats are locked in position properly so that the seat belts will operate efficiently. Refer to the information on the “Rear bench seats” in Section 3. Rear seat functions Refer to the information on the “Rear bench seats” in Section 3. 1.
SEAT BELTS The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats) contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – Have the entire restraint system checked following an accident. – pretensioners, – force limiter, – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – air bags for driver and front passenger.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) A Air bags for driver and front passenger An air bag may be provided for both the driver and the front passenger. Depending on the vehicle, the presence of this equipment is indicated by the word “air bag” on the steering wheel and dashboard (air bag zone A) and a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults 2 Warning light 2 will light up on the instrument panel when the ignition is switched on and then go out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system. Contact your approved dealer as soon as possible. Your protection will be reduced until this fault is rectified.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
SIDE PROTECTION DEVICES Side air bags They can be fitted to the front seats. They are triggered at the side of the seats (door side) to protect the occupants in the event of a severe side impact. A marking on the side of the seat draws your attention to this. Curtain air bags These are air bags fitted to each upper side of the vehicle. They deploy along the front and side windows to protect passengers from severe side impacts.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
METHODS OF RESTRAINT IN ADDITION TO REAR SEAT BELTS Depending on the vehicle, they are composed of: – pretensioners integrated into the inertia reel, – force limiters. These systems are designed to act independently or together when the vehicle is subjected to a frontal impact. There are two possibilities, depending on the force of the impact: – protection is provided by the seat belt only; – the pretensioner is triggered to rectify seat belt slack.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: Choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.36 Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
Child safety: Choosing a child seat mounting Attachment using the ISOFIX system There are two ways of attaching child seats: using the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected.
Child safety: Choosing a child seat mounting (continued) – Place the headrest in the top position or remove it; 1 2 – pass belt 3 (supplied with the seat) between the two rear headrest rods; 3 – the hook 4 must be fitted to the ring 5 located in the luggage compartment; 4 – tighten the belt. 5 The two rings 1 are located between the seatback and the seat squab.
child safety: fitting a child seat (1/24) Fitting child seats Some seats are not suitable for fitting child seats. The diagrams on the following pages show you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
child safety: fitting a child seat (2/24) 2-seater van ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. Child seat attached using the belt ¬ Seat which allows a seat with “Universal” approval to be fitted using a seat belt; Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt.
child safety: fitting a child seat (3/24) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
child safety: fitting a child seat (4/24) The table below summarises the information already shown on the diagram on the following pages, to ensure the applicable regulations are respected.
child safety: fitting a child seat (5/24) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt; check that it can be fitted.
child safety: fitting a child seat (6/24) 5-seater combi Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
child safety: fitting a child seat (7/24) 6-seater combi Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
child safety: fitting a child seat (8/24) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
child safety: fitting a child seat (9/24) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt; check that it can be fitted.
child safety: fitting a child seat (10/24) The table below summarises the information already shown on the diagram on the following pages, to ensure the applicable regulations are respected.
child safety: fitting a child seat (11/24) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt; check that it can be fitted.
child safety: fitting a child seat (12/24) 4-seater Bus Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
child safety: fitting a child seat (13/24) 7-seater Bus Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
child safety: fitting a child seat (14/24) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
child safety: fitting a child seat (15/24) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt; check that it can be fitted.
child safety: fitting a child seat (16/24) The table below summarises the information already shown on the diagram on the following pages, to ensure the applicable regulations are respected.
child safety: fitting a child seat (17/24) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt; check that it can be fitted.
child safety: fitting a child seat (18/24) 8-seater bus Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
child safety: fitting a child seat (19/24) 8-seater combi/bus Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
child safety: fitting a child seat (20/24) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
child safety: fitting a child seat (21/24) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt; check that it can be fitted.
child safety: fitting a child seat (22/24) The table below summarises the information already shown on the diagram on the following pages, to ensure the applicable regulations are respected.
child safety: fitting a child seat (23/24) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt; check that it can be fitted.
child safety: fitting a child seat (24/24) 9-seater combi/bus Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
Child safety: deactivating/activating the front passenger air bag (1/3) DANGER 2 Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered.
Child safety: deactivating/activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
Child safety: deactivating/activating the front passenger air bag (3/3) DANGER 2 Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered.
DRIVING POSITION, LEFT-HAND DRIVE (1/2) 1 29 1.
DRIVING POSITION, LEFT-HAND DRIVE (2/2) The presence of the equipment described below DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 Location for ashtray or cup-holder. 2 Side air vent. 3 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights. 10 Storage compartment or navigation system. 22 Gear lever. 11 Location for: – radio; – radio display; – navigation system controls; – tachograph. 24 Ignition switch. 23 Accessories socket or cigar lighter.
DRIVER’S POSITION, RIGHT-HAND DRIVE (1/2) 1 1.
DRIVER’S POSITION, RIGHT-HAND DRIVE (2/2) The presence of the equipment described below DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 Location for ashtray or cup-holder. 2 Side air vent. 3 Location for passenger air bag. 4 Storage compartment. 5 Centre air vent. 6 Heating and ventilation controls. 7 Location for: – radio, – radio display, – navigation system controls, – tachograph. 8 Storage compartment or navigation system.
Warning lights (1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A g f Front fog light tell-tale Rear fog light tell-tale light Warning light ® requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. Contact an approved Dealer. Instrument panel A The © warning light means you should drive very carefully to an approved dealer as soon as possible.
Warning lights (2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Warning light © This comes on when the igni- STOP light ® This comes on when the igni- tion is switched on and goes out after 3 seconds. If it comes on, possibly accompanied by other warning lights, you should visit an approved dealer as soon as possible. Depending on the vehicle, this warning light is accompanied by a message on the instrument panel.
Warning lights (3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ù Electronic Stability Program (ESP) and traction control (ASR) indicator light. A There are several reasons why the light may come on: refer to the information on the “Electronic stability program: ESP” and “traction control system: ASR” in Section 2. Š ‰ Fuel economy indicator lights This lights up to advise you to change to a higher gear (up arrow) or lower gear (down arrow).
Displays and indicators (1/2) 1 Rev counter 1 (graduations ×100) 2 Speedometer 2 (mph or km/h) Overspeed buzzer Depending on the vehicle, a buzzer sounds for approximately 10 seconds every 40 seconds, as long as the vehicle is travelling in excess of 72 mph (120 km/h). 1.
Displays and indicators (2/2) B A C When the minimum level is reached, the first bar lights up C, alongside the warning light (a fuel pump) on the instrument panel. Total mileage recorder, clock (except vehicles with chronotachograph) and trip mileage recorder. This can be read for approximately 30 seconds after the ignition has been switched on. OR Trip computer and warning system Refer to the information on the “Trip computer” in Section 1.
TRIP COMPUTER: general information (1/2) Selection key 1 on display A A Press button 1 to repeatedly to scroll through the following information: 1 a) Total mileage and trip mileage recorder, b) journey parameters: – fuel consumed; – average fuel consumption; – current fuel consumption; – estimated range; – distance travelled; – average speed; c) mileage before service; Trip computer and warning system A General reset and trip mileage recorder reset key 1 Depending on the vehicle, this includes
TRIP COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting 1 Resetting the journey parameters (reset button) With one of the trip parameters selected as the display, press and hold button 1 until the display resets. The values showing average fuel consumption, range and average speed will become more stable and reliable the further you travel after pressing the reset button.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. FUEL USED 541km b) Journey parameters Fuel consumed since the last reset. AVERAGE 7.3 L/100 Average fuel consumption since the last reset. CURRENT 8.
ON-BOARD COMPUTER: journey parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections RANGE - - - - KM Interpreting the display selected Estimated range with remaining fuel This range takes into account the average fuel consumption since the last time the reset button was pressed. The value is displayed after driving 400 metres.
ON-BOARD COMPUTER: journey parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
ON-BOARD COMPUTER: journey parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected SPEED LIMITER 70KM/H d) Cruise control/speed limiter programmed speed (depending on the vehicle). Refer to the information on the “Cruise control/speed limiter” in Section 2. CRUISE CONTROL 70KM/H NO MESSAGE AVAILABLE 1.80 e) On-board log Successive display: – information messages (automatic lighting, etc.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages ESP OFF BATTERY MODE: ECONOMY OIL LEVEL CORRECT AUTO LIGHTS DEACTIVATED Interpretation of messages Indicates that you have deactivated the ASR function. Indicates that vehicle accessories have been switched off to preserve the battery.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
CLOCK AND EXTERIOR TEMPERATURE (1/2) 1 2 Press and hold the button to enter the hour setting mode. When only the hours are flashing, press the button briefly to scroll through the hours. Confirm by pressing and holding the button on stalk 2. When only the minutes are flashing, press button 2 briefly to scroll through the minutes. Confirm by pressing and holding the button on stalk 2.
CLOCK AND EXTERIOR TEMPERATURE (2/2) External temperature indicator 3 5 4 Special note: When the external temperature is between –3°C and +3°C, the °C characters flash (indicates risk of ice formation). Resetting the clock 3 The time and external temperature appear on display 3. With the ignition on, press button: 4 for minutes. 5 for hours.
REAR VIEW MIRRORS 4 2 3 3 5 A 1 B C Interior rear view mirror Door mirrors The interior rear view mirror is adjustable. When driving at night, tilt small lever 1 to avoid being dazzled by the headlights of the vehicle behind. Push mirror 2 to position it. Mirror 3 is fixed.
EXTERIOR LIGHTING AND SIGNALS (1/3) Automatic operation (depending on vehicle) 1 2 This function can be deactivated or reactivated. 1 u Side lights With the engine running, the dipped beam headlights are switched on or off automatically depending on the level of ambient light, without the need to operate stalk 1 (position 0). To activate or deactivate this function, with the ignition on and engine stopped, move the end of stalk 1 twice in succession from position 0 to the side light position.
EXTERIOR LIGHTING AND SIGNALS (2/3) á f Main beam headlights 3 With stalk 1 in dipped beam headlights position, move the stalk towards you. When the main beam headlights are lit up, an indicator light on the instrument panel lights up. 4 To avoid inconveniencing other road users, remember to switch off the rear fog light when it is no longer needed. Switching off the lights Return the end of stalk 1 to its initial position.
EXTERIOR LIGHTING AND SIGNALS (3/3) 1 With the ignition off and the headlights off, pull stalk 1 towards you: the dipped beam headlights come on for approximately thirty seconds. This action may be carried out no more than four times for a maximum lighting period of two minutes. See-me-home lighting function (depending on vehicle) This function (useful, for example, for opening a gate, a garage, etc.) enables you briefly to switch on the dipped beam headlights.
ELECTRIC BEAM HEIGHT ADJUSTMENT A 1 Control 1 allows you to adjust the height of the headlight beams. Turn control 1 to adjust the headlights according to load. 100 m A Incorrect setting: the lights are set too high and could dazzle other drivers. Turn the control knob downwards to lower the beam. B Correct setting: the beam’s maximum range is between 50 and 100 metres. 1.
WINDSCREEN WASH/WIPE (1/2) n 1 Windscreen wiper With the ignition on, move stalk 1 around the steering wheel: A B C D Windscreen wiper with automatic wiper function With the ignition on, move stalk 1 around the steering wheel: A Park. A Park B Intermittent wiping. The wipers will pause for several seconds between sweeps. B Automatic wiper function: when this position is selected, the system detects water falling on the windscreen and triggers wiping at the appropriate speed.
WINDSCREEN WASH/WIPE (2/2) When the vehicle is stationary, operating stalk 1 overrides and cancels automatic operation. 1 A D Note: if for any reason the wipers cannot move (eg. stuck to windscreen by ice), the system will automatically cut off the power supply to the wipers. B C Vehicles with automatic selection of wiping speed When working in the engine compartment, ensure that the windscreen wiper stalk is in position A (park).
REAR SCREEN WASHER 2 1 Before using the rear wiper, check that no objects are obstructing the travel of the blade. In frosty weather, make sure that the wiper blades are not stuck by ice (risk of motors overheating). Keep an eye on the condition of the blades. Replace the wiper blades as soon as they begin to lose efficiency (approximately once a year). Y Rear screen wiper with timer With the ignition on, turn the end of stalk 1 to align mark 2 with the symbol.
Audible and visual signals 1 A 1 Horn Press steering wheel boss A. Headlight flasher Pull stalk 1 towards you. 2 é Hazard warning lights Direction indicators Press switch 2. Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. This switch lights up all four indicators simultaneously.
FUEL TANK (1/3) Fuel grade Use a high grade fuel that complies with the standards currently in force in each country. Petrol versions 1 A 2 Effective tank capacity: approximately 90 litres. Depending on the vehicle, cover A may unlock at the same time as the doors. Otherwise unlock cap 1 using the door key. Place the cap in cap holder 2 during filling. It is essential to use unleaded petrol. The octane rating (RON) must conform with the information given on the label on the cover A.
FUEL TANK (2/3) Filling with fuel With the ignition switched off, insert the nozzle so that the valve is open and fully insert the nozzle before engaging it in order to fill the tank (risk of splashback). Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made so as to leave sufficient room for expansion.
FUEL TANK (3/3) – operate priming bulb 6 until there are no more air bubbles in the fuel flow, – retighten bleed screw 5, 5 6 – operate priming bulb 6 again, – depending on the vehicle, refit protector 7. The engine can now be restarted. 7 If the engine does not start after several attempts, contact an approved Dealer.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in/Ignition switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting/Stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN/IGNITION SWITCH Petrol version “Ignition on” position M For the first 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. The ignition is switched on: You may only expect top performance from your vehicle after approximately 1,800 miles (3,000 km). – Petrol version: the engine may be started. – Diesel version: the engine is preheating. “Start” position D Service intervals: refer to the Maintenance Service Booklet for the vehicle.
starting/STOPPING THE ENGINE Starting the engine Vehicles fitted with the engine immobiliser system In very cold conditions (temperatures below –20°C): so that it is easier to start the engine, switch on the ignition for several seconds before starting the engine. Make sure that the engine immobiliser is not activated. Refer to information on the “Engine immobiliser” in Section 1.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents overrevving of the engine irrespective of the gear engaged. To avoid faults in icy weather: Running out of fuel You may start the engine normally after refilling the fuel tank even if you have completely run out of fuel, provided that the battery is well-charged.
SPECIAL FEATURES OF DIESEL VEHICLES FITTED WITH A PARTICLE FILTER As a guide, this type of cleaning should take up to 20 minutes. If the © warning light comes on together with particle filter warning light 1, consult an approved dealer as soon as possible. 1 You may need to restart the operation if the vehicle has to stop before the warning light goes out. 2.6 This is due to the exhaust particle filter being cleaned automatically, and does not affect the way the vehicle runs.
GEAR LEVER/HANDBRAKE 1 1 2 Gear lever Handbrake To select reverse gear (vehicle stationary) To release: Move the lever to neutral, then position the lever in reverse. Pull the lever up slightly, press button 2 and then lower the lever to the floor. Ring 1 has to be lifted up to the gear lever knob to select reverse gear. The red warning light on the instrument panel will light up if you are driving with an incorrectly released handbrake.
ADVICE: antipollution, fuel economy and driving (1/3) By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is maintained and used correctly.
ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Sporty driving uses a lot of fuel: drive with a light right foot. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal.
ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² group signature.
Driver correction devices/aids (1/3) Depending on the vehicle, this is composed of: – the ABS (anti-lock braking system); – electronic stability program ESP and traction control ASR; – emergency brake assist. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
Driver correction devices/aids (2/3) Electronic stability program ESP and traction control ASR Electronic stability program ESP This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
Driver correction devices/aids (3/3) Traction control (ASR) offers additional safety; it is recommended that you do not drive with the function disabled. Correct this as soon as possible by pressing switch 1 again. Operating faults When the system detects an operating fault the message “check braking system” appears on the instrument panel along with warning light ©.
Cruise control - speed limiter: limiter function (1/3) Controls 1 Limit speed activation, storage and increase switch (+). 1 4 2 5 3 2 Limit speed activation, storage and recall (R). 3 Switch the function to standby (with limit speed stored) (O). 6 4 Limit speed activation, storage and decrease switch ( - ). 5 Main “On/Off” switch. The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed.
Cruise control - speed limiter: limiter function (2/3) Varying the limit speed The limit speed may be changed by repeatedly pressing: 1 4 Driving When a limit speed has been stored, if this speed is not reached the vehicle behaves in a similar way to a vehicle without the speed limiter function. – Switch 1 (+) to increase the speed; – Switch 4 (-) to decrease the speed.
Cruise control - speed limiter: limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 2 (R). 1 4 2 5 3 Switching off the function The speed limiter function is deactivated if you press switch 5: in this case a speed is no longer stored. The orange instrument panel warning light goes out, confirming that the function is stopped. Putting the function on standby The speed limiter function is suspended when you press switch 3 (O).
Cruise control - speed limiter: cruise control function (1/4) Controls 1 Cruising speed activation, storage and increase switch (+). 1 4 2 5 3 2 Cruising speed activation, storage and recall (R). 3 Switch the function to standby (with storage of governed cruising speed) (O). 4 Cruising speed activation, storage and decrease switch (–). 5 Main “On/Off” switch. The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed.
Cruise control - speed limiter: cruise control function (2/4) Driving 1 Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelerator pedal. 5 6 7 4 Switching on Press switch 5 on the side showing . Indicator light 6 comes on, lit green, and the message “cruise control” appears on the instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed.
Cruise control - speed limiter: cruise control function (3/4) Exceeding the cruising speed 1 4 The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
Cruise control - speed limiter: cruise control function (4/4) Returning to the cruising speed 1 4 2 5 3 If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). At a vehicle speed above 20 mph (30 km/h), press switch 2 (R). Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate more rapidly to reach this threshold.
SEQUENTIAL gearbox (1/6) 2 3 4 1 6 5 Selector lever 1 Display – This allows you to shift directly from first gear to reverse gear, to select reverse gear and neutral and to change gear in manual mode. 2 Gear display – It also allows you to switch between manual and automatic modes at any time, with the engine switched on and a forwards gear engaged, by moving the lever to the left. 5 Automatic mode 2.
SEQUENTIAL gearbox (2/6) Operation Starting Switch on the ignition. Moving forwards (starting in neutral) The display on the instrument panel switches on. The gear display shows N and A. If neutral (N) is displayed, start the engine but do not depress the accelerator. If a gear other than neutral (N) is displayed, it will flash; starting is possible if you depress the brake pedal (indicator light 3 will come on if you forget) when holding the key in the starting position.
SEQUENTIAL gearbox (3/6) Operation in automatic mode Automatic mode is selected by default every time the ignition is switched on. The letter A appears on the display. The vehicle is controlled using the accelerator and the brake. Gears will change automatically at the correct moment and at a suitable engine speed because automatic mode takes into consideration the road surface and the chosen driving style. Gear shift pattern (see the marking on the lever base) Gears may be shifted manually in this mode.
SEQUENTIAL gearbox (4/6) Operation in semiautomatic mode (manual) This mode can be activated at any time when driving by pushing the lever to the left. The change is made without the gears shifting up or down. You can initiate gear changes using the selector lever. To shift up a gear, simply push the selector lever forwards without necessarily releasing the accelerator. To shift down a gear, simply push the selector lever backwards without necessarily releasing the accelerator.
SEQUENTIAL gearbox (5/6) Special circumstances Snow mode When the vehicle is driven on a surface where you are likely to wheelspin (snow, mud, etc.) press the t switch on the dashboard. The indicator light on the instrument panel will light up. Once these driving conditions no longer apply, exit this position by pressing switch again; the operating tell-tale goes out. Switching to snow mode selects the gearbox automatic mode (switching to manual deselects snow mode until automatic mode is selected again).
SEQUENTIAL gearbox (6/6) Audible warning Operating faults – If you hold the vehicle on a slope for too long without applying the brakes or handbrake, you will strain the system (risk of overheating the clutch). If this warning light comes on when the vehicle is in motion, it indicates a fault in the system. In most cases, you may still drive the vehicle, although it will not function perfectly.
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors, fitted in the vehicle’s rear bumper, measure the distance between the vehicle and an obstacle when reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centimetres from the obstacle.
PARKING DISTANCE CONTROL (2/2) Prolonged deactivation of the system You can deactivate the system for prolonged periods by pressing the switch for longer than approximately three seconds. Once deactivated, the system can be reactivated by pressing the button again for longer than approximately three seconds. 1 Temporary deactivation of the system Press switch 1 to deactivate the system. Press it again to reactivate the system.
2.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional heating and air conditioning.
AIR VENTS, air outlets (1/2) 1 2 3 4 8 5 4 3 6 7 8 1 Left-hand side window demister. 5 Control panel. 2 Side air vent. 6 Side air vent. 3 Windscreen demisting vents. 7 Right-hand side window demister. 4 Centre air vents. 8 Front footwell heater outlets. 3.
AIR VENTS, air outlets (2/2) 2 2 2 1 1 Air vents Air flow Move the control knob 1 (beyond the point of resistance). 1 To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. w maximum air flow. b closed. Direction Right/left: move tab 2. Up/down: press or lift tab 2. Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). There is a risk of damage or of fire. 3.
AIR CONDITIONING (1/5) A B C D E Adjusting the amount of air blown into the passenger compartment Turn control C. The passenger compartment is ventilated by blown air. The blower determines how much air enters the passenger compartment, but vehicle speed also has some influence on this. The further the control is positioned to the right, the greater the amount of air blown into the passenger compartment.
AIR CONDITIONING (2/5) B1 B Air recirculation control Press button B: operating tell-tale light B1 comes on. Under these conditions, air is taken from the passenger compartment and is recirculated, with no air being taken from outside the vehicle. Recirculation allows: – isolating the vehicle from the external atmosphere (driving in polluted areas, etc.); – the passenger compartment to be brought to the desired temperature as quickly as possible.
AIR CONDITIONING (3/5) E i The air flow is distributed between all the air vents, the front side window demisting air vents, the windscreen demisting vent and the footwells. W Close the dashboard vents for more effective demisting. All the air is directed towards the windscreen and front side window demisting vents. In this position, demisting may be more effective if the air conditioning is switched on at the same time. Distribution of air in the passenger compartment Turn control E.
AIR CONDITIONING (4/5) Air conditioning controls C Button D switches the air conditioning on or off. D D1 The system cannot be switched on if control C is set to 0. Using the air conditioning system enables you to: – lowering the temperature inside the passenger compartment; – eliminate condensation more quickly. Note: The air conditioning may be used in all conditions but does not operate when the external temperature is low.
AIR CONDITIONING (5/5) B In very hot weather or when the vehicle has been parked in the sun, open the doors for a few moments to let the hot air escape before starting the engine. To lower the temperature to the desired comfort level use the passenger compartment isolation function B. Once the desired comfort level is obtained, stop recirculation mode. D D1 If no cold air is produced Check that the controls are set correctly and that the fuses are sound.
AUTOMATIC CLIMATE CONTROL (1/9) 1 2 3 4 5 6 12 Heated rear screen with demisting function and heated door mirrors (depending on vehicle). 8 7 13 Heated rear screen warning light. 14 Air recirculation control. 9 14 13 12 11 10 The controls 5 Display. 1 Clear View button to demist and de-ice the windows. 6 Starting the automatic air conditioning. 2 Clear View function indicator light. 8 and 10 Passenger compartment air distribution adjustment.
AUTOMATIC CLIMATE CONTROL (2/9) 4 6 7 – press button 7 to increase the temperature; – press button 4 to decrease the temperature. Note: The maximum and minimum settings of 15°C and 27°C allow the system to produce a minimum or maximum temperature, whatever the ambient conditions. Ambient temperature: automatic mode Automatic mode Press button 6. Only the temperature and the AUTO symbol are displayed. Functions managed in automatic mode are not displayed.
AUTOMATIC CLIMATE CONTROL (3/9) Ambient temperature: (automatic mode) (continued) Operation To reach and keep the chosen comfort level and to maintain good visibility, the system controls: – ventilation speed; – air distribution; – air recirculation management; – air conditioning start/stop; – air temperature. The displayed temperature values show a comfort level.
AUTOMATIC CLIMATE CONTROL (4/9) 5 Adjusting automatic mode Automatic mode is the normal operating mode of the system (AUTO warning light lit on display 5) but you may alter the selections made by the system (air distribution, etc.). These options are explained on the following pages.
AUTOMATIC CLIMATE CONTROL (5/9) 5 6 8 ö ó The air flow is directed towards all the air vents and the passenger footwells. The air flow is directed mainly towards the footwells. 10 Distribution of air in the passenger compartment There are five possible combinations for air distribution, which may be selected by pressing buttons 8 and 10 repeatedly. The arrows on display 5 indicate the setting selected: õ ÷ All the air flow is directed to the demisting vents for the windscreen and the side windows.
AUTOMATIC CLIMATE CONTROL (6/9) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. 3 5 6 Automatic mode is switched off by pressing buttons 9 and 11. 9 These buttons allow you to increase or decrease ventilation speed. Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions.
AUTOMATIC CLIMATE CONTROL (7/9) 13 12 Rear screen de-icing/ demisting With the engine running, press button 12, and operating tell-tale 13 comes on. To exit this function, press button 12 again. Demisting automatically stops by default. This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). 3.
AUTOMATIC CLIMATE CONTROL (8/9) 1 2 Note: if you wish to reduce the air flow (which may produce a certain amount of noise in the passenger compartment), press button 11. 6 To exit this function, press either: – button 1 again; – button 6 (the AUTO indicator light on the display will light up). 13 12 Clear View function With the engine running, press button 1, and operating tell-tale 2 comes on. The AUTO button indicator light (on the display) goes out.
AUTOMATIC CLIMATE CONTROL (9/9) 14 Air recirculation mode Pressing button 14 activates air recirculation (the symbol lights up on the display). During recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle. Air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.).
AIR CONDITIONING: information and advice on use Operating faults Fuel consumption You will normally notice an increase in fuel consumption (especially when driving in town) when the air conditioning is operating. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and therefore helping to preserve the environment: Drive with the air vents open and the windows closed.
ADDITIONAL AIR CONDITIONING (1/2) 2 1 When fitted to the vehicle, the vehicle has four adjustable air vents and, depending on the version, the following controls: – Heating and air conditioning; – Automatic climate control. Note: avoid closing the four air vents at the same time (risk of damaging the system components). Heating and air conditioning system Move control(s) 1 to vary the amount of air required.
ADDITIONAL AIR CONDITIONING (2/2) 4 5 6 3 Automatic climate control 3 Automatic mode on and off.. 4 Adjusting the amount of cold air. 5 Adjusting the amount of warm air. 6 Automatic mode Button 5 has an operating tell-tale: – indicator light on, the function is switched on; – indicator light off, the function is switched off. 3.
WINDOWS 1 Front manual window winders 2 Sliding rear windows Press tab 2 and slide the window. Turn handle 1. Sliding windows and doors Before moving them, ensure that no passenger has part of their body outside the window or door. 3.
WINDOWS (continued) Automatic operation (depending on vehicle) This is in addition to the operation of the driver’s window winder described previously. Press switch 3 briefly to raise or lower the window completely. Pressing switch 3 again while the window is moving will stop the operation. 3 4 Front driver’s side electric window Front passenger’s side electric window With the ignition on, press switch 4 to lower the window or lift switch 4 to raise it.
INTERIOR LIGHTING 1 2 3 Tilting light 1, 2, 3 or 4 provides: – continuous lighting; – intermittent lighting; – no lighting. Intermittent lighting Vehicle with remote control locking unit Opening a front door or, depending on the vehicle, one of the other doors, switches on all the courtesy lights. Vehicle without remote control locking unit 4 All the courtesy lights will come on when a front or rear door is opened. 3.
SUN VISOR/GRAB HANDLE 1 Sun visor Lower sun visor 1. 2 1 The sun visor can be swung round against the window. Grab handle 2 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. 3.
ASHTRAY/CIGAR LIGHTER/ACCESSORIES SOCKET 1 A B 2 Ashtray on dashboard Front cigar lighter Accessories socket Depending on the vehicle, it may be located on either side of the dashboard (location A or B). Depending on the vehicle, with the ignition on, push in the cigar lighter 2. Depending on the vehicle, this is located in the cigar lighter socket 2. It will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in.
PASSENGER COMPARTMENT STORAGE (1/3) 4 1 5 3 7 2 Location 1 This location can be used as a cup holder, a storage compartment or as a receptacle to fit the ashtray. 6 Dashboard storage compartment 4 and 6 3.26 To open, press control 5. Depending on the vehicle, the glove box may have ventilation and air conditioning (one 1.5 litre bottle can be stored there).
PASSENGER COMPARTMENT STORAGE (2/3) 8 10 9 Location 8 This location can be used as a cup holder, a storage compartment or as a receptacle to fit the ashtray. Front door storage compartment and cup holder 9 Location 10 This storage space may be used as a cup holder. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of injury if hot liquid escapes. 3.
PASSENGER COMPARTMENT STORAGE (3/3)/REAR ACCESSORIES socket 13 A B 14 11 12 Storage compartment 11 Storage compartment 13 Accessories socket 14 is designed for connecting accessories with a maximum power rating of 120 Watts (voltage: 12 V) which have been approved by our Technical Department. Ski case 12 To open, press (movement A), then lower (movement B).
REAR BENCH SEATS (1/2) 1 1 2 2 A 3 4 Depending on the vehicle, there may be two rear bench seats: bench seat 2 (2nd row of seats) and bench seat 1 (3rd row of seats). Bench seat 2 To facilitate access to the last row of seats (bench seat 1), detach the seat belt of bench seat 2 by unlocking it from its unit 3 and move control 4 downwards (movement A) to tilt the bench seatback. Remember to lock the seat belt in place once more when a passenger is occupying the seat.
REAR BENCH SEATS (2/2) 5 1 6 7 C D B Bench seat 1 This can be folded and, depending on the vehicle, retracted. To fold it down – Lift seatback unlocking control 5; – fold down the seatback onto the seat base. When moving the rear bench seat, check that the bench seat anchorage points are clean (they should be free from grit, cloths or any other item which may prevent the bench seat from locking securely). 3.
REAR BENCH SEATS: functions (1/2) 3 1 3 2 F A B C Functions of bench seats 1 and 2 Removal These are removed and refitted in the same way. Bench seat 1 can be fitted in the first or last row. Bench seat 2 can only be fitted in the first row. Note: in all cases, if the bench seat is not equipped with catch 3, it is fixed.
REAR BENCH SEATS: functions (2/2) 3 Fitting – position the bench seat over the front anchorage points; – push the bench seat until it sits over the rear anchorage points; Ensure that the bench seats are locked in place correctly when refitting them. Check that the side seat belts are locked in their unit correctly. – lower latches 3 and push them until they lock. The rear bench seats must be placed on their original anchorage points. Driving with the bench seat in a rear-facing position is prohibited.
TRANSPORTING OBJECTS (1/3) 2 1 3 A 4 7 6 5 Luggage net A If fitted, this can be used when transporting animals or luggage to isolate them from the passenger section. It can be positioned: – behind the front seats; – behind a rear bench seat.
TRANSPORTING OBJECTS (2/3) 2 1 3 A 5 8 4 Fitting the luggage net A behind the rear seats Inside the vehicle on each side: Upper mounting: – lift and hold cover 1 to access the mounting hole; – insert the upper rod 2 of the net into largest section 3 of the hole; Lower mounting: – attach hook 5 of the net strap to ring 8 or, depending on the vehicle, to ring 9; – adjust the net strap so that it is taut. Removal Loosen the strap. Detach the belts.
TRANSPORTING OBJECTS (3/3) 10 12 11 11 13 In the rear load area Depending on the vehicle, rails 10, each fitted with two rings 11, prevent transported objects from moving around. The sole purpose of these rings is to prevent transported objects from moving. The objects must be secured to the mounting rings on the vehicle floor beforehand. You can slide the rings onto the rail to position them in the desired location. To do this, pull out the button and slide the ring at the same time.
LUGGAGE COVER B A A Removal Depending on the vehicle, lift parcel shelf A or B until it is vertical and then push the joints on either side to unlock it. To refit, carry out the above operations in reverse order. Do not place any objects, especially heavy or solid objects on the luggage cover. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.
MULTIMEDIA EQUIPMENT 1 3 4 2 The presence and location of this equipment depends on the vehicle’s multimedia equipment. 1 Display; 2 radio; 3 steering column control; 4 multimedia sockets. To use this equipment, consult the instructions for the equipment which should be kept with the other vehicle documentation. 3.
3.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil change . . . . . . . . . . . . . . . . . . .
BONNET (1/2) 4 2 3 5 1 To open the bonnet, pull handle 1. The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling fan can come on at any moment. Risk of injury. 4.2 Unlocking the bonnet catch To unlock, pull catch 2. In the event of any impact, no matter how slight, against the radiator grille or bonnet, have the bonnet catch checked by an approved Dealer as soon as possible.
BONNET (2/2) 4 3 Closing the bonnet To close the bonnet, replace stay 3 back into its holder 4, hold the bonnet in the middle and lower it to 20 cm above the closed position, then release it. It will latch automatically under its own weight. Ensure that the bonnet is properly locked. etc.). Ensure that nothing is preventing locking (grit, cloths, After carrying out any work in the engine compartment, check that nothing has been left behind (cloth, tools, etc.).
Message 1 Level above minimum Message 2 Minimum level 4.4 if the level is at the minimum level: the word “oil” flashes (display mes- ø lights sage 2) and warning light up on the instrument panel, depending on the vehicle. It is vital to top up the oil as soon as possible. Reading the oil level The vehicle must be parked on level ground and the engine should have been switched off for some time beforehand to obtain an accurate reading.
ENGINE OIL LEVEL: general information (2/2) B A C B A Once the operation has been completed, ensure that the dipstick is pushed in as far as it will go or that the cap-type dipstick is completely screwed in. Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels.
ENGINE OIL LEVEL: topping up/filling (1/3) 1 1 2 3 3 1 2 Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Booklet for your vehicle for information regarding which grade of oil to use.
ENGINE OIL LEVEL: topping up/filling (2/3) 2 – top up the level (as a guide, the capacity between the minimum and maximum reading on the dipstick 2 is between 1.5 and 2 litres, depending on the engine); 1 – wait for approximately 10 minutes to allow the oil to flow into the engine; – check the level using the dipstick 2 (as described above). Once the operation has been completed, ensure that the dipstick is pushed in as far as it will go or that the cap-type dipstick is completely screwed in.
ENGINE OIL LEVEL: topping up/filling (3/3)/OIL CHANGE Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil changes Oil filter included (for information) 2.0 16V engine : 5.35 litres 1.9 dCi engine : 4.70 litres 2.0 dCi 16V engine: 7.7 litres Filling: take care when topping up the oil that no oil drips onto engine components - risk of fire.
LEVELS (1/4) 1 Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Service Booklet for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anti-corrosion protection of the cooling system.
LEVELS (2/4) Level When the engine is cold, the level should be visible between the MINI and MAXI levels on reservoir 1. 1 For topping up or refilling with oil, use products approved by our technical department. Power-assisted steering pump 1 Checking intervals: Refer to the Maintenance Service Booklet for your vehicle. Take care when working in the engine compartment as the engine cooling fan may start to operate at any moment without warning. Risk of injury. 4.
LEVELS (3/4) 1 Level 1 Filling It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warning line. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Only use fluids approved by our technical department (and taken from a sealed container).
LEVELS (4/4)/FILTERS 1 The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle. Windscreen/headlight washer reservoir Filling With the engine switched off, open cap 1, fill until you can see the fluid, then refit the cap. Fluid Special windscreen washer fluid (product with antifreeze in winter).
BATTERY B 1 3 2 4 5 2 7 6 2 A 8 Battery2 It is located under the front carpet on the left-hand side. – Lift the carpet; – remove the bolts 1 and remove cover A. It does not need to be serviced: never attempt to open it. If you have to replace the battery, the replacement battery should not have side handles. Handle the battery with care as it contains sulphuric acid, which must not come into contact with eyes or skin. If it does, wash the affected area with plenty of cold water.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Protection against the effects of corrosive agents Although your vehicle has been treated with very effective anti-corrosion products, it nevertheless remains subject to the effects of different parameters.
Bodywork maintenance (2/2) You should Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Service Booklet. Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
4.
Section 5: Practical advice Tool kit/Hubcap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing a wheel. . . . . . . . . . . . .
TOOL KIT (1/2) 2 8 A 1 7 3 4 6 Depending on the vehicle, tool kit 1 is located under the driver’s seat. Lift tool kit cover A. Jack 2. Special end piece 3 for the emergency spare wheel. To take it out, rotate the kit until it can be removed. Offset wrench 4. Hubcap tool 5. Ratchet wrench 6. Towing hitch 7. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 5.2 5 Jack extension piece 8.
TOOL KIT (2/2)/HUBCAP 2 8 6 A B 9 C 10 7 10 Jack assembly Do not leave the tools unsecured inside the vehicle as they may come loose under braking. After use, check that all the tools are correctly clipped into the tool kit, then position it correctly in its housing: there is a risk of injury. D Remove the hubcap using hubcap tool 10 (located in the tool kit) by engaging the hook into one of the openings around the edge of the hubcap. 10 Unclip this using hubcap tool 10 (located in the tool kit).
EMERGENCY SPARE WHEEL 1 To refit emergency spare wheel B A 2 Proceed in reverse order. Check that wheel carrier 4 is correctly positioned before tightening nuts 6 and 5. 4 6 B 5 3 On equipped vehicles, use tool A, comprising: – ratchet wrench 3; – extension piece 2; – for some versions, special end piece 1 (which must be added). These components are located in the tool kit described previously.
TYRE INFLATION KIT (1/4) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/4) 3 3 2 A 1 4 Depending on the vehicle, in the event of a puncture, use the inflation kit located underneath the driver’s seat. Move the driver’s seat forward and fold down the seatback to access the inflation kit. 5 A 2 Screw compressor adapter 1 to bottle 2 and clip the bottle onto compressor A. The bottle must remain in an upright position. Unscrew the valve cap on the tyre concerned. Open it.
TYRE INFLATION KIT (3/4) Note: whilst the cylinder is emptying (approximately 30 seconds), pressure gauge 7 will indicate briefly a pressure of up to 6 bar. Then the pressure drops. Store the kit under the driver’s seat and secure it with the strap. If the correct pressure cannot be achieved, repair is impossible. Do not drive the vehicle. Consult an approved dealer.
TYRE INFLATION KIT (4/4) Precautions when using the kit – The kit should not be operated for more than 15 consecutive minutes; – When driving, vibration may be felt due to the presence of the repair product injected into the tyre. 1 Start the vehicle immediately in order to the distribute the product in the tyre and, after 6 miles (10 km) or 10 minutes driving, stop to check the pressure. To do this, fit adapter 1 onto the tyre’s valve.
CHANGING A WHEEL (1/2) Start cranking the jack up by hand to align the base plate (which should be pushed slightly under the vehicle). Place a plank of wood under the base plate if on soft ground. 1 3 Insert adapter 1 and raise the wheel off the ground. 2 Switch on the hazard warning lights. Keep the vehicle away from traffic and on a level surface where it will not slip (if necessary, place a solid support under the jack base).
CHANGING A WHEEL (2/2) Loosen the wheel nuts and remove the central hubcap, then the wheel. Fit the emergency spare wheel in place on the central hub. Position the central hubcap, tighten the nuts and unscrew the jack. With the wheels on the ground, tighten the nuts as fully as possible and check the tightness as soon as possible (tightening torque 142 Nm). Anti-theft bolt If you use anti-theft bolts, fit these nearest the valve (otherwise it may not be possible to fit the wheel trim).
TYRES (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads. 1 You must make sure that your tyres conform to local road traffic regulations.
TYRES (2/3) Tyre pressures Please respect the tyre pressures for all wheels (including the emergency spare wheel) and check them at least once a month, especially before a long journey (please refer to the information on “Tyre pressures” at the beginning of this document). Incorrect tyre pressures lead to abnormal tyre wear and unusually hot running.
TYRES (3/3) Use in winter – Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains must not be fitted to tyres which are larger than those originally fitted to the vehicle. – Snow or winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion.
HEADLIGHTS: changing halogen bulbs A Main headlight and dipped beam headlight Remove the connector from bulb 1. Remove cover A. Unclip spring 3 and remove the bulb. 3 2 Bulb type: H4. 1 Do not touch the bulb glass. Hold it by its base. Replace the bulb, replace the spring and the connector and check that cover A is replaced correctly. To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an approved dealer.
HEADLIGHTS: front fog lights, additional lights/side lights Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. 2 3 1 Front fog lights 1 Side indicator lights Changing a bulb Unclip indicator light 3 (using a flatblade screwdriver or similar). Consult an approved dealer. Turn bulb holder 2 a quarter of a turn and take out the bulb.
REAR LIGHTS: changing bulbs (1/4) 2 1 1 A 1 Rear light unit A Remove bolt 1. A 2 4 3 2 Turn the light unit slightly and release it from its mounting points 2 to access the bulb holder 3. Side and brake lights 4 Unclip the bulb holders by rotating them a quarter of a turn. Direction indicators 5 Unclip the bulbs by pressing them slightly and rotating them a quarter of a turn. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
REAR LIGHTS: changing bulbs (2/4) 7 6 6 B Rear light unit B Remove bolt 6. Release the headlight unit. Turn the bulb holder 7 or 8 and release it. Replace the bulb concerned. 8 7 Reversing light Pear-shaped, bayonet type P 21W bulb. 8 Fog light (or nothing) Pear-shaped, bayonet type P 21W bulb. Refit the bulb holder and secure it by turning. Check that it is securely mounted. Reposition the headlight unit and screw it in place. The bulbs are under pressure and can break when replaced.
REAR LIGHTS: changing bulbs (3/4) 9 10 High-level brake light on rear hinged door version Remove nut 9. Remove the light from the outside to access bulb 10. Pear-shaped, bayonet type P 21W bulb. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
REAR LIGHTS: changing bulbs (4/4) 11 12 13 High-mounted brake light on tailgate version Remove nut 11. Remove the light from the outside to access bulb 12. Pear-shaped, bayonet type P 21W bulb. Number plate light The bulb is accessed in the same way for both vehicles with hinged doors and those with the tailgate. Unscrew lens 13 to access the bulb. Bulb type: W 5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTS: changing bulbs (1/2) C A B 1 2 Courtesy light A Courtesy light B, C Unclip lens 1. Unclip lens 2 on the side indicated (using a flat-blade screwdriver or similar). Release the bulb. Bulb type: 7W festoon type bulb. Bulb type: 10W or 15W festoon type bulb (depending on version). The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTS: changing bulbs (2/2) D 2 3 4 Light D Unclip lens 2 on the side indicated (using a flat-blade screwdriver or similar). Open flap 3 at the rear of the courtesy light or light. Release bulb 4. Bulb type: 10W or 15W festoon type bulb (depending on the version). The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/3) Refer to the fuse allocation label (shown on the page opposite) on the cover to identify the fuses. 1 It is not advisable to use the free fuse locations. 2 A Fuse box 1 Disconnect the fuse using tweezers 2. To remove the fuse from the tweezers, slide the fuse to the side. If an electrical component fails to operate, check that the fuses are sound before carrying out any other checks. Open cover A. Check the fuse in question and replace it, if necessary, by a fuse of the same rating.
FUSES (2/3) Allocation of fuses (the presence of fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation f Windscreen washer/ wipers. ß Air bags/Brake lights/ Diagnostic socket. n Anti-lock braking system. E Rear screen wiper. Right-hand side lights. h Front window winders. F Rear fog light/ Reversing lights. Á Main beam headlights. Ì Horn. É Hazard warning lights. g Door mirror de-icing. £ Tachograph/Heated seats. U Front fog lights/ Reversing lights.
FUSES (3/3) Allocation of fuses (the presence of fuses depends on the vehicle equipment level) Symbol Symbol Allocation î Radio/Radio display/ Navigation system/ Wipers. x Heating system. ; Consumer cut-out (navigation system, radio etc.). x Rear air conditioning. G Front fog lights. Boiler Additional heater. Central door locking/ Speed limiter controls/ Storage compartment light. º Cigar lighter/ Accessories socket. » Accessories sockets. t Front heating and air conditioning system.
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (courtesy lights, etc.
BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts.
RADIOFREQUENCY REMOTE CONTROL: batteries (1/2) A 1 Remote control A Replacing the batteries Unclip remote control cover 1 (using a coin). 2 Replace battery 2 according to the direction marked on the cover. Note: It is not advisable to touch the electronic circuit in the key cover when replacing the battery. The batteries are available from approved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical contact.
RADIOFREQUENCY REMOTE CONTROL: batteries (2/2) B 3 5 4 Remote control B Replacing the batteries Remove screw 3, open the case at slot 4 using a coin, and replace battery 5, observing the polarity shown on the back of the cover. Note: It is not advisable to touch the electrical circuit in the key cover when replacing the battery. The batteries are available from approved Dealers, and their service life approximately two years.
FITTING A RADIO 2 – In all cases, it is very important to follow the manufacturer’s instructions carefully. – The specifications of the brackets and wires (available from our network) vary depending on the equipment level of your vehicle and the type of radio. 1 Consult an approved Dealer to find out the correct part number. Radio location 1 Speakers Unclip the cover blanking the radio location 1. The connections are found behind the cover: aerial, + and – supply, and speaker wires.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Use of transmission/ receiving devices (telephones, CB equipment etc.
TOWING: breakdown (1/2) The steering wheel must be unlocked and the ignition key must be in position M (ignition on) to provide brake lights and hazard warning lights on the towed vehicle. At night the vehicle must have its lights on. Never use the drive shafts or axles. These towing points may only be used for pulling the vehicle, never for lifting it either directly or indirectly. Unhitch the trailer, etc., if one is being towed.
TOWING: breakdown (2/2) 6 2 5 4 Accessing the towing hitch 3 It is located in tool kit 2: turn the whole of the tool kit to extract it. When storing the tools, ensure that they are correctly replaced in kit 2, in their original position and store the kit under the driver’s seat. Do not leave the tools unsecured inside the vehicle as they may come loose under braking. 5.
TOWING A 1 1 Fitting the towing ball Screw the towing ball hitch into the two mounting holes 1. Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Please refer to the manufacturer’s instructions on how to fit and use the bars. Please keep these instructions with the rest of the vehicle documentation. Fitting towing equipment A: 933 mm 5.
WIPER BLADES 4 1 A 2 B 3 Replacing windscreen wiper blades – Lift the wiper arm 3. – Turn the wiper blade 1 until it is horizontal. – Press tab 2 and slide the wiper blade downwards to release hook 4 from the wiper arm. – Slide the blade (A) then lift it (B). To refit To refit the wiper blade, proceed in reverse order to removal. Make sure that the blade is correctly locked in position. 5.34 C Check the condition of the wiper blades.
Operating faults (1/4) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO Warning lights dim or fail to come on; the starter does not run. Battery terminals disconnected, oxidised or incorrectly secured. Contact an approved Dealer. Battery discharged or worn. Connect another battery to the faulty battery.
Operating faults (2/4) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to the correct pressure, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved dealer. Coolant boiling in the coolant reservoir. Mechanical fault: damaged cylinder head gasket. Stop the engine. Contact an approved Dealer. Smoke under the bonnet. Short circuit or cooling system leak.
Operating faults (3/4) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved Dealer. The engine is overheating. The coolant temperature warning light and the STOP warning light come on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved Dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved Dealer as soon as possible.
Operating faults (4/4) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb. See the information on “Headlights: changing halogen bulbs” or “Rear lights: changing bulbs” in Section 5. The direction indicators do not work.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weights. . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION plates A 6 7 8 9 10 1 2 3 4 5 11 12 13 A Quote the manufacturer’s identification plate (right-hand side) in all correspondence or when ordering parts. B 6.2 Vehicle identification plate A 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 Maximum permissible all-up weight. 3 Total train weight (vehicle fully loaded, with trailer). 4 Front axle maximum permissible weight.
ENGINE IDENTIFICATION plates A 1 2 3 A A Quote the information on the identification plate or label A in all correspondence or when ordering parts. Engine identification 1 Engine type 2 Engine suffix 3 Engine number A 6.
DIMENSIONS (in metres) 26251 Basic vehicle without options Q Z1 K C A E G D B Y H Z Y1 J F 6.
DIMENSIONS (in metres) Complete vehicles without recent alterations VAN Standard chassis Raised van Long chassis Standard van Standard van Raised van A 3.098 3.498 B 4.782 5.182 C 0.833 D 0.851 E 1.615 F 1.630 G 2.232 H (1) 1.955 → 2.477 J(1) 0.523 → 0.545 K 0.145 → 0.160 (2) Q 1.913 1.387 1.913 Y 1.167 1.370 1.167 Y1 Z Z1 1.390 1.818 1.335 2.400 1.818 2.800 (1) Unladen (2) Laden 6.
DIMENSIONS (in metres) Q Z1 K C A D E G B Y H Z Y1 J F 6.
DIMENSIONS (in metres) Complete vehicles without recent alterations Standard chassis Standard combi COMBI A B C D E F G H(1) J(1) K(2) Q Y Y1 Z Z1 With 3rd row bench seat Long chassis Raised combi Without 3rd row bench seat With 3rd row bench seat Without 3rd row bench seat Standard combi With 3rd row bench seat Without 3rd row bench seat 3.098 4.782 0.449 1.253 Raised combi With 3rd row bench seat Without 3rd row bench seat 3.498 5.182 0.449 0.833 0.851 1.615 1.630 2.232 1.942 → 1.968 0.
DIMENSIONS (in metres) Q Z1 K C A D E G B Y H Z Y1 J F 6.
DIMENSIONS (in metres) Complete vehicles without recent alterations BUS Standard chassis Long chassis A 3.098 3.498 B 4.782 5.182 C 0.833 D 0.851 E 1.615 F 1.630 G 1.904 H (1) 1.947 → 1.961 1.908 → 1.960 J(1) 0.538 → 0.557 0.548 → 0.554 K 0.151 → 0.173 (2) 0.150 → 0.187 Q 1.317 Y 1.370 Y1 1.390 Z Z1 1.306 0.449 0.849 (1) Unladen (2) Laden 6.
WEIGHTS (in kg): versions marketed depend on country The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer.
WEIGHTS (in kg): versions marketed depend on country The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer.
ENGINE SPECIFICATIONS 2.0 16V 1.9 dCi 2.0 dCi 16V Engine type (see engine plate) Versions F4R F9Q M9R Cubic capacity (cc) 1 998 1 870 1 998 Type of fuel Octane Rating It is essential to use unleaded petrol and this must be of the octane rating stated on the label inside the fuel filler flap. If not available, for a limited time only, use unleaded fuel: – with an octane rating of 91 for a label showing 95 or 98; Diesel The label located inside the fuel filler flap indicates authorised fuels.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
Anticorrosion check (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/4) A ABS.................................................................................... 2.12 accessories........................................................................ 5.30 accessories socket.................................................... 3.25, 3.28 advice on antipollution..............................................2.8 → 2.10 air bag...........................................................1.27 → 1.30, 1.32 activating the front passenger air bags..................
Alphabetical index (2/4) F filter..................................................................................... 4.12 particle filter.................................................................... 2.6 fitting a radio....................................................................... 5.29 front passenger air bag deactivation.................................. 1.63 front seat adjustment.......................................................... 1.19 front seats....................................
Alphabetical index (3/4) luggage compartment cover............................................... 3.36 M maintenance: bodywork........................................................... 4.14 – 4.15 interior trim......................................................... 4.16 – 4.17 mechanical........................................................6.14 → 6.19 mileage before service......................................6.14 → 6.19 methods of restraint in addition to rear seat belts.............. 1.
Alphabetical index (4/4) T tailgate....................................................................3.33 → 3.36 tanks and reservoirs: windscreen washer....................................................... 4.12 technical specifications............................ 6.2, 6.10 – 6.11, 6.13 temperature regulation.............................................3.9 → 3.18 tool kit.......................................................................... 5.2 – 5.3 towing............................................
( www.renault.ie ) ( www.renault.co.uk ) ( www.renault.is ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
