SANDERO DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome aboard your vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... 5 . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle Keys/Radio frequency remote control: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locking/unlocking the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opening/closing the doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine immobiliser system. . . . . . . . . . . . . . . . . . . . . . . .
KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) B A 2 3 4 1 Key A 1 Coded key for ignition switch, doors and fuel filler cap. Radio frequency remote control B 2 Locking the doors and tailgate. 3 Unlocking the doors and tailgate. 4 Coded key for ignition switch, driver’s door and fuel filler cap. Driver’s responsibility Never leave your vehicle with the keys inside when leaving a child (or animal) in the car, even for a short period.
KEYS, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) The remote control unit operating range This varies according to the environment. It is therefore important when handling the remote control to ensure that you do not lock or unlock the vehicle by inadvertently pressing the buttons. Interference The presence of certain objects (metal objects, mobile telephones, or an area with strong electromagnetic radiation, etc.
RADIO FREQUENCY REMOTE CONTROL: use Doors are locked and unlocked using remote control unit B. It is powered by a battery which must be replaced (refer to the information on the “Radio frequency remote control: batteries” in Section 5). B B 1 Locking the doors Unlocking the doors Press locking button 1. Press unlocking button 2. The hazard warning lights and side indicator lights flash twice to indicate that the doors have locked.
LOCKING/unlocking THE DOORS 1 2 3 Manual locking Electric central locking Child safety From the outside Depending on the vehicle, it can be used to simultaneously lock or unlock the doors and luggage compartment. To make it impossible for the rear doors to be opened from the inside, move lever 3 on each door and check from the inside that the doors are securely locked.
OPENING AND CLOSING THE DOORS Driver’s responsibility when parking or stopping the vehicle 2 3 1 Opening the doors manually from the outside Opening the doors from the inside With the doors unlocked (refer to the information on “Locking/unlocking the doors” in Section 1). Front: pull handle 3. Front: Place your hand behind handle 1 and pull it towards you.. Rear (manual opening): lift unlocking button 2 from the inside and move the door handle. 1.
ENGINE IMMOBILISER This prevents the vehicle being driven by anyone not in possession of the vehicle’s coded ignition key. Operating faults After the ignition has been switched on, if warning light 1 continues to flash or remains continuously lit, there is a system operating fault. Operating principle The vehicle is automatically protected a few seconds after the ignition is switched off.
FRONT HEADRESTS 1 A B 2 2 3 4 Adjusting the height of headrest A To refit headrests A or B Press tab 1 and simultaneously slide the headrest to the required position. Insert headrest rods 2 into the holes (tilt the seatback backwards if necessary). Push the headrest in until it locks in position. To raise the headrests A or B Depending on the vehicle, press tabs 1 and 2 on the head restraint guides or on button 3 or 4 and lift the headrest to release it (tilt the seatback backwards if necessary).
FRONT SEATS 4 5 1 2 3 To move forwards or backwards Lift bar 1 to release. Release the bar in the desired position and ensure it locks in place properly. To raise or lower the driver’s seat surface Depending on the vehicle, lift lever 2, adjust the seat base to the desired height, then release the lever. 2 Heated seats Depending on the vehicle, with the ignition on, press switch 3. The system, which has a thermostat, decides whether or not the heating is needed.
STEERING WHEEL, CLOCK 2 2 1 3 Adjusting the steering wheel Resetting the clock Depending on the vehicle version, the height of the steering wheel can be adjusted. Lift lever 1 and place the steering wheel in the desired position; lower the lever to lock the steering wheel. With the ignition on, select display 2 showing the total mileage and clock. Make sure that the steering wheel is correctly locked. For safety reasons, only adjust the steering wheel when the vehicle is stationary. 1.
SEAT BELTS (1/4) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Make sure that the rear bench seat is locked in position correctly so that the rear seat belts will operate efficiently. Refer to the information on the “Rear bench seat: functions” in Section 3. Incorrectly adjusted or twisted seat belts may cause injuries in the event of an accident. Use one seat belt per person, whether child or adult.
SEAT BELTS (2/4) 7 4 Depending on the vehicle, it comes on when the engine is started if the driver’s seat belt is not fastened. When the vehicle is being driven, it comes on and a beep sounds for approximately 2 minutes until the driver’s seat belt is fastened. 5 6 To fasten Unwind the belt slowly and smoothly and ensure that buckle 4 locks into catch 6 (check that it is locked by pulling on buckle 4). If the belt jams, allow it to return slightly before attempting to unwind it again.
SEAT BELTS (3/4) 7 8 7 11 9 Rear central seat belts 7 14 10 15 16 (depending on the vehicle) Fasten sliding buckle 11 into red catch 10. Unwind the belt slowly from its housing 8. Rear side seat belts 12 Click the buckle into black catch 9. 13 12 The belts are locked, unlocked and adjusted in the same way as the front belts. Rear lap belt with manual adjustment 13 (depending on the vehicle) The strap should be worn flat over your thighs and against your pelvis.
SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For special operations (e.g. fitting child seats) contact an approved Dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – Have the entire restraint system checked following an accident. – seat belt pretensioners; – chest-level load limiters; – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical. – air bags for the driver and front passenger.
SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain level of impact force, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Driver’s and passenger air bags These may be provided for the driver and the front passenger seats. The air bag system uses pyrotechnic principles.
SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation In this case, a child seat MUST NOT be fitted to the front passenger seat. This system is only operational when the ignition is switched on. Allowing any other passenger to sit in that seat is not recommended. If a severe frontal impact occurs, the air bag(s) inflate(s) rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and the front passenger’s head against the dashboard.
SYSTEMS IN ADDITION TO THE FRONT SEAT BELTS (4/4) 2 All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
SIDE PROTECTION DEVICES Side air bags These air bags may be fitted to the front seats and are deployed at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Warnings concerning the side air bag – Fitting seat covers: seats equipped with an air bag require covers specifically designed for your vehicle. Contact an approved dealer to find out if such covers are available from our Network.
ADDITIONAL methods of RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The airbag is designed to complement the action of the seat belt. Both the airbags and seat belts are integral parts of the same protection system. It is therefore essential to wear the seat belt at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports the head and neck. Choose a bucket type seat for better side protection and replace it as soon as the child’s head extends past the seat shell.
child safety: mounting a child seat (1/2) Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
child safety: mounting a child seat (2/2) It is essential to use the luggage compartment anchorage point 3 to attach the upper belt of the child seat. 1 It is forbidden to use other mounting points to attach this strap. 2 The two ISOFIX rings 1 are located between the seatback and the seat base and are clearly visible. To ensure your child seat can be easily fitted and locked on rings 1, use access guides 2 on the child seat. 3 The third ring is used to attach the upper strap on some child seats.
Child safety: Fitting a child seat (1/6) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
Child safety: Fitting a child seat (2/6) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. Before installing a child seat in the ISOFIX anchoring points on a rear side seat, check that the seat belt buckles are not placed between the two ISOFIX anchorage points in this seat. If necessary, move the buckle for the seat concerned towards the centre of the vehicle.
Child safety: Fitting a child seat (3/6) Vehicles without airbag or with airbag deactivated Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. 1 ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
Child safety: Fitting a child seat (4/6) Vehicles with passenger air bag not deactivated Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. 1 Child seat attached using the belt ² A child seat must not be fitted in this seat ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. Only if the seat is equipped with an 1 inertia-reel belt.
Child safety: Fitting a child seat (5/6) The table below summarises the information already shown on the diagram on the previous pages, to ensure the regulations in force are respected.
Child safety: Fitting a child seat (6/6) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF = Seat which, on equipped vehicles, allows forward-facing child seats with “Universal” approval to be attached by the ISOFIX system; check that it can be fitted.
child safety: deactivating/activating the front passenger air bag (1/3) 2 1 Deactivating the front passenger air bag (depending on vehicle) To fit a rear-facing child seat on the front passenger seat, you must deactivate the front passenger air bag if your vehicle is fitted with air bag deactivation. To deactivate the passenger air bag, with the vehicle stopped and the ignition off, press and turn button 1 to the OFF position. 1.
child safety: deactivating/activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
child safety: deactivating/activating the front passenger air bag (3/3) 2 1 Operating faults Activation of the front passenger air bag (depending on vehicle) You should reactivate the air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of your front passenger in the event of an impact. To reactivate the air bag: with the vehicle stopped and the ignition off, press and turn button 1 to the ON position.
REAR VIEW MIRRORS 1 B 0 A 2 Door mirrors with manual adjustment Door mirrors with electrical adjustment: To adjust the mirror, move lever 1. With the ignition on, move button 2: – position A to adjust the left-hand door mirror; – position B to adjust the right-hand door mirror; Foldable door mirrors Fold the door mirror manually against the door window. 3 Interior rear view mirror Its position can be adjusted.
DRIVER’S POSITION, LEFT-HAND DRIVE (1/2) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 29 2 3 4 28 27 26 5 25 23 22 1.
DRIVER’S POSITION, LEFT-HAND DRIVE (2/2) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 10 Side air vent. 21 Electric door mirror control. 2 Demister outlet. 11 Passenger air bag activation/deactivation switch. 22 Location for ashtray or cup holder. 3 Stalk for: – direction indicator lights, – exterior lights, – front fog lights, – rear fog lights, – horn. 4 Instrument panel. 5 Location for driver’s air bag.
driver’s position, right-hand drive (1/2) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 29 1.
driver’s position, right-hand drive (2/2) The presence of the equipment DEPENDS ON THE VEHICLE VERSION AND COUNTRY. 1 Side air vent. 10 Side air vent. 2 Demister outlet. 11 Fuse box. 3 Storage compartment or location for passenger air bag. 12 Bonnet release. 4 Centre air vents. 5 Stalk for: – direction indicator lights, – exterior lights, – front fog lights, – rear fog lights. 6 Instrument panel. 7 Location for driver’s air bag (depending on vehicle). 13 Headlight beam height adjustment control.
Warning lights (1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A m o # Dipped beam headlight telltale light x Main beam headlight tell-tale light This light comes on when the ignition is switched on and goes out within three seconds. If it lights up when you are driving, it indicates a fault in the antilock braking system. Braking will then be as normal, without the ABS system: contact an approved dealer urgently.
Warning lights (2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ô Coolant temperature warning light This goes out as soon as the engine starts. If it comes on when driving, it indicates an increase in the coolant temperature. Stop and let the engine idle for a minute or two; the temperature should fall. If it does not fall, stop the engine and allow it to cool before checking the coolant level. If the level is normal, there is another cause.
Warning lights (3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. D A Instrument panel A û The warning light requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. Contact an approved Dealer. 1.42 Handbrake on and brake circuit incident warning light If it lights up, check that the hand brake is fully released.
Displays and indicators (1/2) 1 2 Rev counter 1 (rpm × 1 000) Speedometer 2 (km or miles per hour) Overspeed buzzer Speedometer 2 Dual speed scale (miles per hour and km per hour) (depending on vehicle) Depending on the vehicle, a buzzer sounds for approximately 10 seconds every 30 seconds, as long as the vehicle is travelling in excess of 72 mph (120 km/h). 1.
Displays and indicators (2/2) Multifunction key 5 – Display selection A 3 By pressing the button you can shift from the total mileage recorder, trip mileometer and time or vice-versa. – Resetting the trip mileage recorder 4 5 Once the trip mileage display is selected, press and hold the button. – Resetting the clock Refer to the information on the “Clock” in Section 1. Fuel gauge 3 Multifunction display A The number of squares lit shows the fuel level.
TRIP COMPUTER AND WARNING SYSTEM (1/4) The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Refer to the table on the following pages showing display examples. 1 2 Display 1 General reset and trip mileage recorder reset key 2 To reset the trip mileage recorder, the display must show the Trip mileometer function. Press and hold button 2.
TRIP COMPUTER AND WARNING SYSTEM (2/4) The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Interpreting some of the values displayed after resetting The values showing average fuel consumption, range and average speed will become more stable and reliable the further you travel after pressing the reset button. For the first few miles after pressing the reset key you will notice that the range increases as you travel.
TRIP COMPUTER AND WARNING SYSTEM (3/4) The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing 3 Interpreting the display a) Total mileage recorder. b) Trip mileage recorder. c) Fuel used since the last time the reset button was pressed. d) Average fuel consumption since the last time the reset button was pressed.
TRIP COMPUTER AND WARNING SYSTEM (4/4) The information displayed DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing 3 Interpreting the display e) Estimated range with remaining fuel This range takes into account the average fuel consumption since the last time the reset button was pressed. The value is displayed after driving around 400 metres. f) Distance travelled since the last reset. g) Average speed since the last reset.
EXTERIOR LIGHTING AND SIGNALS (1/2) á 1 2 Main beam headlights With stalk 1 in dipped beam headlights position, move the stalk towards you. When the main beam headlights are lit, an indicator light lights up on the instrument panel. To return to the dipped beam headlight position, pull the switch stalk towards you. e u Side lights Turn the end of stalk 1 until the symbol is opposite mark 2. k Dipped beam headlights Turn the end of stalk 1 until the symbol is opposite mark 2.
EXTERIOR LIGHTING AND SIGNALS (2/2) e 3 3 4 Turning off the fog lights Turn centre ring 3 again to position the symbol corresponding to the fog light or off position opposite mark 4. The corresponding indicator light goes out on the instrument panel. The front and rear fog lights switch off when the exterior lights are switched off. g Front fog lights Turn the centre ring of stalk 3 until the symbol is opposite mark 4. The fog lights only light up if the exterior lights have been switched on.
ADJUSTMENT OF HEADLIGHT BEAM HEIGHT Vehicle load conditions Setting position of control A Basic setting: luggage compartment empty and only the driver on board or with one front passenger. 0 Luggage compartment empty, 1, 2, 3 passengers 1 Luggage compartment full, 3 passengers 2 Luggage compartment full, driver only 3 A Control A is used to adjust the height of the headlight beams according to the load. Turn control A anticlockwise to lower the beams and clockwise to raise them. 1.
AUDIBLE AND VISUAL SIGNALS 1 3 1 2 Horn Press the end of the stalk 1. é Hazard warning lights Direction indicators Press switch 3. Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. Depending on the vehicle, press on one of areas 2. This switch activates all four direction indicators and the side indicator lights simultaneously.
WINDSCREEN WASH/WIPE, DE-ICING (1/3) s With the ignition on, pull stalk 1 towards you. 1 A B D n Windscreen wiper C A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer. In frosty weather, make sure that the wiper blades are not stuck by ice (risk of motor overheating). A longer pull will trigger three sweeps of the wipers, in addition to the windscreen washer. Keep an eye on the condition of the blades.
WINDSCREEN WASH/WIPE, DE-ICING (2/3) p 1 Rear screen washer/ wiper (depending on vehicle) With the ignition on, turn the end of stalk 1 to align the symbol with mark 2. When the stalk is released, it returns to the rear wipe position. 2 Y Rear screen wiper (depending on vehicle) With the ignition on, turn the end of stalk 1 to align the symbol with mark 2. Before using the rear wiper, check that no object is obstructing the travel of the blade.
WINDSCREEN WASH/WIPE, DE-ICING (3/3) 2 2 V Heated rear screen With the engine running, press button 2 (the indicator light on the instrument panel lights up). This function de-ices/demists the rear screen and the electric de-icing rearview mirrors (depending on the vehicle). The operation is stopped: – automatically after it has been running for 12 minutes (the indicator light goes out); – by pressing button 2 again (the indicator light goes out). 1.
FUEL TANK (1/3) A Do not mix even small amounts of petrol (unleaded or E85) with diesel. Do not use ethanol-based fuel if your vehicle is not compatible with this fuel. Do not add any additives to the fuel, you risk damaging the engine. B 1 Capacity of the fuel tank: 50 litres approximately. The cap can be unlocked with the ignition key. For details on filling the fuel tank, refer to the information on “Filling with fuel”.
FUEL TANK (2/3) Filling with fuel A Insert the nozzle to open valve B and insert it fully before turning it on to fill the fuel tank (risk of splashing). Hold it in this position for the whole filling operation. Following the first automatic shut-off at the end of filling, the trigger can be pulled two more times at most, to leave room for expansion. B Petrol version It is essential to use unleaded petrol.
FUEL TANK (3/3) 2 No modifications whatsoever are permitted on any part of the fuel supply system (computers, wiring, fuel circuit, injector, protection covers, etc.) as this may be dangerous (such work must be undertaken by qualified Network personnel). 3 Priming bulb (diesel version) After a breakdown caused by completely running out of fuel, the system must be reprimed before the engine is restarted: Note: the bulb is always located on the right-hand side of the engine compartment.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in, ignition switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting/stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN, IGNITION SWITCH Petrol version Ignition on position M For the first 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. The ignition is switched on: You may only expect top performance from your vehicle after approximately 1,800 miles (3,000 km). – diesel version: the engine is preheating. – petrol version: the engine may be started. Service intervals: refer to the Maintenance Service Booklet for the vehicle.
STARTING/STOPPING THE ENGINE Starting the engine In very cold conditions (temperatures below –20°C): so that it is easier to start the engine, switch on the ignition for several seconds before starting the engine. Make sure the engine immobiliser is not activated. Refer to the information on the “Engine immobiliser” in Section 1. Vehicle equipped with an automatic gearbox É Before starting, move the lever to position N or P.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using oil or fuel additives which are not approved by the manufacturer.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injection pump which prevents the engine speed being exceeded irrespective of the gear selected. To avoid any faults in icy weather: When driving, depending on the fuel grade used, it is possible that white smoke may be emitted. This is due to the exhaust particle filter being cleaned automatically, and does not affect the way the vehicle runs.
ADVICE: antipollution, fuel economy and driving (1/3) By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is maintained and used correctly.
ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system On versions with an automatic gearbox, it is preferable to keep the gear lever in position D. The exhaust gas monitoring system detects operating faults in the vehicle’s antipollution system. These faults may cause mechanical damage or the release of harmful substances. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level.
ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
ENVIRONMENT Emissions Your vehicle has been designed to emit fewer greenhouse gases (CO2) while in use, and therefore to consume less fuel (e.g. 140 g/km, equivalent to 5.3 l/100 km for a diesel vehicle). Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
GEAR LEVER 1 To select reverse gear (vehicle stationary) Vehicle with manual gearbox Move the lever to neutral, then follow the gate shown on knob 1. Vehicle with automatic gearbox Refer to the information on the “Automatic gearbox” in Section 2. The reversing light will come on as soon as reverse gear is selected (ignition on). 2.10 An impact to the underside of the vehicle while manoeuvring (e.g.: striking a post, raised kerb or other street furniture) may result in damage to the vehicle (e.g.
HANDBRAKE, POWER-ASSISTED STEERING To apply Pull lever 1 upwards and make sure the vehicle is immobilised. Power-assisted steering With the engine running, do not leave the steering wheel at full lock while stationary as this may damage the powerassisted steering pump. With the engine switched off, or if there is a system fault, it is still possible to turn the steering wheel. The force required will be greater.
DRIVER CORRECTION DEVICES/AIDS (1/2) Depending on the vehicle, this is composed of: – the ABS (anti-lock braking system); – emergency brake assist. ABS (anti-lock braking system) Under heavy braking, the ABS prevents the wheels from locking, allowing the stopping distance to be managed and keeping control of the vehicle. Under these circumstances, the vehicle can be steered to avoid an obstacle whilst braking.
DRIVER CORRECTION DEVICES/AIDS (2/2) Operating faults x – Warning light lights up on the instrument panel: the ABS is deactivated. Braking safety is still guaranteed. – x D and are lit on the instrument panel, this indicates a fault in the braking system. In both cases, consult an approved Dealer. Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping distances. Operating principle The system is for detecting an emergency braking situation.
AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode 1 Move lever 1 to position D. In the majority of traffic conditions, you will not have to touch the gear selector lever again: the gear will be changed automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particular driving style you have chosen.
AUTOMATIC TRANSMISSION (2/3) Special cases 1 4 In certain driving conditions (e.g.: to protect the engine) the “automated system” may change the gear automatically. 5 Likewise, to prevent incorrect manoeuvres, a gear change may be refused by the automatic system: in this case the gear display flashes for a few seconds as a warning.
AUTOMATIC TRANSMISSION (3/3) – If the road contour and bends in the road do not allow you to stay in automatic mode (e.g.: in mountainous areas), it is recommended that you switch to manual mode. This will prevent the automatic gearbox from changing gears repeatedly when climbing, and permit engine braking on long descents. – In cold weather, start the engine and wait a few seconds before moving the selector lever from position P or N and engaging it in D or R to prevent the engine stalling.
Section 3: Your comfort Air vents, air outlets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heating, Ventilation, Air conditioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use . . . . . . .
AIR VENTS, air outlets (1/2) 1 2 1 Left-hand side air vent 2 Left-hand side window demister vent 3 Windscreen demisting vents 4 Centre air vents 5 Control panel 3.
AIR VENTS, air outlets (2/2) 10 11 10 Centre and side air vents Air flow To open air vent 10 or 12, press on the air vent (point 11) until it is open as far as required. 12 To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Direction To direct the air flow, swivel air vent 10 or 12. Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). There is a risk of damage or of fire. 3.
HEATING, VENTILATION, AIR CONDITIONING (1/2) B Note: The air conditioning may be used in all conditions but does not operate when the external temperature is low. C – Button B not activated (warning light off). The air conditioning is not operating. The heating and ventilation controls are the same as a vehicle without air conditioning. – Button B activated (warning light on). The air conditioning is operating.
HEATING, VENTILATION, AIR CONDITIONING (2/2) B F If no cold air is produced Check that the controls are set correctly and that the fuses are sound. If they are not, switch off the heating and air conditioning system (warning light integrated into button B) and contact an authorised dealer. Adjusting the air temperature. Move control F to obtain the desired temperature. The further the control is in the red, the more the temperature will be increased.
Manual air conditioning (1/3) A B C D E F Distribution of air in the passenger compartment Turn control A. W Close the dashboard vents for more effective demisting. All the air is then directed to the windscreen and front side window demister outlets. i The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. Controls A Adjusting the distribution of air in the passenger compartment.
Manual air conditioning (2/3) C E y Adjusting the ventilation speed Turn control C from 0 to 4. The passenger compartment is ventilated by blown air. The blower determines how much air enters but vehicle speed has a slight effect on this. The further the control is positioned to the right, the greater the amount of air blown into the passenger compartment. G J The air flow is directed towards the dashboard vents and the footwells. All the air flow is directed to the dashboard vents.
Manual air conditioning (3/3) Prolonged use of this position (isolation mode) may mist up the windows slightly or cause odours due to the air not being renewed. It is therefore advisable to return to normal operation (external air) by pressing control D when you have passed through the polluted area. D Air recirculation operation (isolation of the passenger compartment) (depending on vehicle) Turn control D towards air recirculation symbol â.
AIR CONDITIONING: information and advice on use Fuel consumption Operating faults You will normally notice an increase in fuel consumption (especially when driving in town) when the air conditioning is operating. As a general rule, contact your approved dealer in the event of an operating fault. For vehicles fitted with air conditioning with no automatic mode, switch off the system when it is not required.
INTERIOR LIGHTING 1 Courtesy light Pressing switch 1 provides: – continuous lighting; – or temporary lighting by opening one of the front doors, or by opening one of the four doors, depending on the vehicle. The light only goes out when the doors are correctly closed; – no lighting. 2 Automatic operation of interior lighting (depending on the vehicle) – if the doors are unlocked using the remote control, the lighting is switched on for approximately 30 seconds.
ELECTRIC WINDOWS (1/2) 1 2 3 4 5 Front electric windows Rear electric windows With the ignition on, press the bottom of switch 1 or 2 to open the window or press the top of switch 1 or 2 to close it. With the ignition on, press switch 3 or 4 to open the window or raise switch 3 or 4 to close it.
ELECTRIC WINDOWS (2/2) Safety of rear occupants 6 The driver can inhibit operation of the rear electric windows by pressing switch 5. Driver’s responsibility Manual window winder controls Turn handle 6 to lower or raise the window to the desired height. Never leave your vehicle with the key or remote control inside and never leave a child (or a pet) unsupervised, even for a short while.
SUN VISOR/GRAB HANDLE 1 2 3 4 5 6 7 Sun visor Pivot sun visor 1 or 5 against the windscreen. OR Unclip the sun visor from its mounting 3 or 4 and pivot it against the door window. Vanity mirror (depending on the vehicle) The passenger sun blind is fitted with a courtesy mirror 6 on the passenger side. Grab handle 7 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.
ASHTRAYS/CIGAR LIGHTER/ACCESSORIES SOCKET Ashtray It can be housed in either position 2 or 4. 2 Lift cover 3 to open. Remove the ashtray to empty it. 1 3 4 Cigar lighter 1 With the ignition on, push in the cigar lighter 1. It will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. OR Accessories socket 1 It is provided for connecting accessories approved by our Technical Department with a maximum power of 120 Watts (12 V).
PASSENGER COMPARTMENT storage space and fittings (1/2) 1 A Passenger side glove box Pull handle 1 to open it. This glove box can be used to store A4 format documents. Storage compartment 2 (or passenger air bag location) Inside the cover, there are two storage spaces for pens and maps. Precautions during use Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.
PASSENGER COMPARTMENT storage space and fittings (2/2) 5 3 4 Centre console storage compartment 3 (or radio location) Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 3.
REAR HEADRESTS A 1 B A 2 A 4 3 A B 1 Adjusting the height of the headrests A Press the tab on catch 1 on each of the rods on headrest A and simultaneously slide the headrest. To remove the headrests A Press the tabs on the catches 1 and 4 and remove the headrest. Child headrest storage position B (depending on the vehicle) When the headrest is set at the lowest position, this is for storage only. It should not be in this position when a seat is occupied.
REAR BENCH SEAT: functions To reposition the seatback Raise the seatbacks. Check the seatbacks are correctly locked in position. 1 2 – W hen returning the seatback to its normal position, make sure that it is properly locked at the top. 3 To fold down the seatback Remove the rear headrests (if fitted). Lower handle 1. Lower seatbacks 2 and 3. moved. When moving the rear bench seat, make sure the anchorage points are clean (they should be free from grit, cloths, toys etc.). 3.
LUGGAGE COMPARTMENT, TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Transporting objects in the luggage compartment Always position the objects transported so that the largest surface is against: – The back of the rear bench seat, for normal loading. 2 1 Manual control Electric central locking To open, insert the key in the lock and turn it clockwise. The tailgate is locked and unlocked at the same time as the doors. Remove the key and press button 1. Lift the luggage compartment lid.
ROOF BARS 3 1 2 Access to the mounting points (depending on the vehicle) Open the doors. Behind seal 2 are blanking bolts 1 which protect the mounting bolt locations. When fitting roof bars, replace the blanking bolts with the mounting bolts supplied with the roof bars. Never remove blanking bolts 1 without plugging the holes afterwards. 3.20 Roof bars 3 (depending on the vehicle) Luggage can be transported on the roof rack mounted on the roof bars.
REAR PARCEL SHELF 1 2 Removal Unhook the two cords 1 (tailgate side). Lift rear parcel shelf 2 slightly and pull it towards you. To refit it, proceed in reverse order to removal. Do not place any objects, especially heavy or hard objects, on the parcel shelf. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.
3.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil change . . . . . . . . . . . . . . . . . . . . . .
BONNET (1/2) 5 2 4 1 3 To open the bonnet, pull the handle 1. Opening the bonnet Unlocking the bonnet catch Lift the bonnet, release stay 4 from its holder; for your safety, always fix it in location 5. To unlock, raise the bonnet slightly and release hook 2 by pushing tab 3 to the left. The engine may be hot during operations in close proximity. In addition, the engine cooling fan may come on at any moment. Risk of injury. 4.
BONNET (2/2) 5 4 Closing the bonnet Before closing the bonnet, check to make sure that nothing has been left in the engine compartment. To close the bonnet, replace stay 4 back into its holder 5, hold the bonnet in the middle and lower it to 20 cm above the closed position, then release it. It will latch automatically under its own weight. etc.).
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is sometimes necessary to top up the level between oil changes. A B However, contact your approved dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: topping up/filling (1/2) 2 2 1 2 1 1 1.4 – 1.6 Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position. Risk of injury.
ENGINE OIL LEVEL: topping up/filling (2/2) Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change oil filter included. (for information) 1.2 16V engines: 4.00 litres 1.4 engines : 3.30 litres 1.6 engines : 3.30 litres 1.6 16V engines: 4.80 litres 1.5 dCi engines : 4.10 litres Engine oil grade Refer to the Maintenance Service Booklet for your vehicle.
LEVELS (1/3) 1 Level Topping up It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warning line shown on brake fluid reservoir 1. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from the manufacturer’s network or web site.
LEVELS (2/3) Checking intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). 2 If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; 3 – anti-corrosion protection of the cooling system. Replacement intervals Coolant With the engine switched off and on level ground, the level when cold must be between the “MINI" and “MAXI" marks on reservoir 2.
LEVELS (3/3) 5 4 Power-assisted steering fluid reservoir 4 or 5 Level: for a correct level when cold, with the engine switched off and on level ground, it must be visible between the “MINI" and “MAXI" marks on reservoir 4 or 5. For maintenance operations on the power-assisted steering, contact an approved dealer. If you feel any variation in the effectiveness of the power-assisted steering, consult an approved dealer.
FILTERS The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. 2 Resetting the air filter clogging sensor 1 Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle. Passenger compartment filter A If your vehicle is not originally fitted with a passenger compartment filter, it is possible to have one retrofitted. Contact an approved dealer.
Tyre pressure Tyre safety and use of snow chains A Refer to the information on “Tyres” in Section 5 for details of the maintenance conditions and, depending on the vehicle version, the use of chains. Special note The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. G: tyre pressure for front wheels, recommended for optimising fuel consumption. B: dimension of the tyres fitted to the vehicle. C: tyre pressures for the front wheels (non-motorway).
BATTERY Battery requiring maintenance A 2 3 4 6 5 Checking intervals: Every six months, open cover 1. Remove the caps and check the level. 1 Liquid Distilled or demineralised water to 1.5 cm above the plates. Never add electrolyte or other products. Replacing the battery Depending on the vehicle, the battery may be a low maintenance version. Low maintenance battery A label on the battery will indicate if the battery is the low maintenance type.
BODYWORK MAINTENANCE (1/3) A well-maintained vehicle will have a longer service life. It is therefore advisable to maintain the vehicle exterior regularly.
BODYWORK MAINTENANCE (2/3) You should – R espect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway). – Always follow the recommendations supplied with the high-pressure cleaning equipment (jet distance and pressure).
BODYWORK MAINTENANCE (3/3) – After cleaning your vehicle, check the brakes while driving at low speed to ensure that the braking efficiency has not been reduced by the water. If it has, depress the brake pedal gently while driving to dry the brakes. – C heck the drain holes at the bottom of the doors to make sure they are not blocked. – R emember to visit the body shop periodically in order to maintain your anticorrosion warranty. Refer to the Maintenance Service Booklet.
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will have a longer service life. It is therefore advisable to maintain the vehicle interior regularly. Glass instrument panel (e.g.: instrument panel, clock, exterior temperature display, radio display). Stains should always be dealt with quickly. Whatever type of stain is on the trim, use soapy water (if possible, warm water) containing: Use a soft or cotton cloth.
INTERIOR TRIM MAINTENANCE (2/2) Removing/refitting factory fitted removable equipment in the vehicle If you need to remove equipment to clean the passenger compartment (e.g. mats), always make you refit it properly and on the correct side (driver’s side mats must be fitted on the driver’s side, etc.), using retaining components supplied with the equipment (e.g. the driver’s side mat must always be secured using prefitted retaining devices).
4.
Section 5: Practical advice Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel trims/Wheels. . . . . . .
TOOLS 3 5 4 2 3 1 4 2 Accessing the tools Towing hitch 1 The tools are stored in the luggage compartment. Refer to the information on “Towing: breakdown” in Section 5. The presence of the tools depends on the vehicle. 1 Wheelbrace 2 (depending on the vehicle) This is used to tighten/loosen the wheel bolts and, depending on the vehicle, to access the emergency spare wheel. Jack 3 Do not leave the tools unsecured inside the vehicle as they may come loose under braking.
PUNCTURE Emergency spare wheel This is stored in cage 3 under the floor at the rear of the vehicle. To access it: – Open the tailgate. – Undo nut 1 with the wheelbrace found in the luggage compartment; refer to the information on “Tools” in this section; 1 – Detach the cage using handle 2. 2 In the event of a puncture, depending on the vehicle, you will have: 3 4 – Remove the emergency spare wheel 4. An emergency spare wheel or tyre inflation kit (refer to the information on the following pages).
TYRE INFLATION KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/3) 1 2 3 – press switch 5 to inflate the tyre to the recommended pressure (check the label affixed to the edge of the driver’s door); 4 – after a maximum of 5 minutes, stop inflating and read the pressure (on the pressure gauge 4); 5 6 8 9 7 Depending on the vehicle, in the event of a puncture, use the kit located in the boot. Open the kit, remove caps 1 and 3 (it is essential not to remove the cap from the bottle) then screw bottle 2 to its support 3.
TYRE INFLATION KIT (3/3) 10 – affix driving recommendation label 10 to the dashboard where it can easily be seen by the driver; – store the kit; – after the first inflation procedure the tyre will still be leaking; it is vital to drive in order to plug the hole; – start immediately and drive at between 12 and 36 mph (20 and 60 km/h) to distribute the product evenly throughout the tyre, stopping after a distance of 2 miles (3 kilometres) to check the pressure; 8 – if the pressure is above 1.
WHEEL TRIM/WHEELS (1/2) 1 B 2 1 3 D C 4 A Wheel trim with concealed wheel bolts Central clipped wheel trim with concealed wheel bolts Remove the wheel trim using the hubcap tool 1, by inserting the tool into valve recess 2. Remove the wheel trim using hubcap tool 1, inserting the tool into valve recess 3 and pulling. To refit it, align it with valve 2. Push the retaining hooks in fully, starting with side A near the valve, followed by B and C, finishing at D opposite the valve.
WHEEL TRIM/WHEELS (2/2) 1 8 7 9 6 Central wheel trim with concealed wheel bolts Central wheel trim with concealed wheel bolts Central wheel trim with visible wheel bolts 9 Remove the wheel trim using the hubcap tool by inserting tool 6 into valve recess 7. Remove it using hubcap tool 1, inserting the tool into recess 8 provided. To remove it without removing the wheel, press it at the points indicated by the arrows.
CHANGING A WHEEL (1/2) Present the jack horizontally, the jack head must slide in the lower slot in the body, as close as possible to the wheel concerned. Switch on the hazard warning lights. Keep the vehicle away from traffic and on a level surface where it will not slip (if necessary, place a solid support under the jack base). Apply the parking brake and engage a gear (first or reverse, or P for automatic transmissions). Ask the passengers to leave the vehicle and to keep away from traffic.
CHANGING A WHEEL (2/2) Turn the wheelbrace until the wheel lifts off the ground. Remove the bolts. Take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and lower the jack.
TYRES (1/3) Tyre and wheel safety 1 The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 When they need to be replaced, only tyres of the same make, size, type and profile should be used. Tyres fitted to the vehicle should either be identical to those fitted originally or conform to those recommended by your approved Dealer.
TYRES (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, assume an increase of 0.2 to 0.3 bar.
TYRES (3/3) Use in winter Chains Snow chains must be fitted to the front wheels. Snow or Winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion. Warning: These tyres sometimes have a specific direction of rotation and a maximum speed index which may be lower than the maximum speed of your vehicle. Studded tyres This type of equipment may only be used for a limited period and as laid down by local legislation.
FRONT LIGHTS: changing bulbs Front side light Remove bulb holder 4 to access the bulb. Bulb type: W5W. 1 2 3 A The following bulbs can be replaced. However, we would advise you to have them replaced by an approved dealer if it proves difficult. Main beam headlights, dipped beam headlights Remove cover A. To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an approved dealer. 4 Remove bulb connector 1.
FOG LIGHTS: changing bulbs Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. 1 Front fog lights 1 Consult an approved dealer. Bulb type: H11. The bulbs are under pressure and can break when replaced. Risk of injury. The engine may be hot during operations in close proximity. In addition, the engine cooling fan may come on at any moment.
REAR LIGHTS: changing bulbs (1/2) 4 3 2 1 Remove screw 1 and detach the rear light cluster from the outside. 6 Detach the foam 2. Carefully unclip the bulb holder by pressing on the tabs 3. Refitting To refit, proceed in the reverse order, taking care not to damage the wiring. 5.16 5 4 Side light and brake light Pear-shaped, bayonet type bulb with two P 21/5 W filaments. 5 Direction indicator light Pear-shaped, bayonet type bulb, P 21 W or PY 21 W (depending on the vehicle).
REAR LIGHTS: changing bulbs (2/2) 7 10 8 9 11 High-level brake light 7 The bulb for the high-level brake light 7 may be accessed through the luggage compartment. Carefully unclip the bulb holder by pressing on the tabs 8. Turn the bulb holder 9 a quarter of a turn, release it and take out the bulb. Bulb type: P 21 W. Number plate light 10 Release it using a flat-blade screwdriver tool or similar. Unclip the lens 11 from the bulb holder to gain access to the bulb. Bulb type: W 5 W.
INDICATOR LIGHTS: changing bulbs 1 Unclip the indicator light 1 (using a flatblade screwdriver or similar). 2 Turn bulb holder 2 a quarter of a turn and take out the bulb. Bulb type with white indicator light: WY5W. Bulb type with orange indicator light: W5W. 5.
INTERIOR LIGHTS: changing bulbs (1/3) 1 Courtesy light Unclip lens 1 using a flat-blade screwdriver or similar. 2 Remove the bulb concerned. Bulb type 2: W5W. Remove the bulb concerned. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTS: changing bulbs (2/3) 4 5 6 3 Glove box light Press tab 4 to release lens 6 and access bulb 5. Unclip light 3 using a flat-blade screwdriver or similar, by pressing on the tab to move the light towards the inside of the unit. Bulb type: W5W. (depending on vehicle) Disconnect the light. 5.
INTERIOR LIGHTS: changing bulbs (3/3) 7 8 9 6 Luggage compartment light Unclip light 6 using a flat-blade screwdriver or similar, by pressing on the tab to move the light towards the inside of the luggage compartment. Press tab 7 to release lens 9 and access bulb 8. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
Fuses (1/3) 2 B A 1 Passenger compartment fuses Tweezers 2 If any electrical component does not work, check the condition of the fuses. Unclip flap A using notch 1 to help you. Disconnect the fuse using tweezers 2, on the back of flap A. To remove the fuse from the tweezers, slide the fuse to the side. It is not advisable to use the free fuse locations. Use the fuse allocation label on the back of flap A to identify the fuses.
Fuses (2/3) Allocation of fuses (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) Symbol Allocation Symbol Allocation Symbol Allocation n ABS ] Central locking of doors and tailgate ḽ Electric front windows î Radio C Rear screen de-icing Z Interior lighting ß Brake lights Ù Not used e Electric door mirror à Air conditioning Ì Horn à Heating G Front fog lights ô Main power supply à Not used a Instrument panel Injection ñ Heated seats Å Air bag f
Fuses (3/3) Allocation of fuses (the presence of certain fuses DEPENDS ON THE VEHICLE EQUIPMENT LEVEL) Symbol Q 5.
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery; The battery charger must be compatible with a battery with nominal voltage of 12 volts. – when charging, stop the charger before connecting or disconnecting the battery; Do not disconnect the battery when the engine is running.
BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts.
RADIO FREQUENCY REMOTE CONTROL: battery 3 1 2 Replacing the battery Unscrew screw 1 then unclip cover 2. Replace battery 3 according to the direction marked on the cover. Note: It is not advisable to touch the electronic circuit in the key cover when replacing the battery. Battery type: CR 2016. Batteries can be obtained from an approved Dealer. These batteries have a service life of approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical contact.
wiper blades 4 D 2 3 1 E A 6 – free them from the windscreen or rear screen when they have not been used for a long time. C – With the ignition off, lift wiper arm 3. – Turn the blade horizontally (movement A). – Press tab 2 and slide the wiper blade downwards (movement D) until hook 4 on the wiper arm is released. – Slide the blade (movement C) then lift it (movement B) to release it.
Towing: breakdown (1/2) Towing procedure The steering wheel must be unlocked and the ignition key must be in position M (ignition on) to provide stop lights and hazard warning lights on the towed vehicle. Always switch on the lights when driving at night. Remove any trailer. It is also essential to observe the towing regulations imposed by current legislation in each country, and not to exceed the towable weight for your vehicle. Consult an approved dealer.
Towing: breakdown (2/2) Towing a vehicle with an automatic gearbox 7 With the engine switched off, the transmission is no longer lubricated. It is preferable to tow this type of vehicle on a trailer or tow it with the front wheels off the ground. Under exceptional circumstances, you may tow the vehicle with all four wheels on the ground, only going forward, with the gear lever in the N position, and for a distance not exceeding 30 miles (50 km).
TOWING equipment A A = 701.2 mm. Permissible nose weight, maximum permissible towing weight braked and unbraked: Refer to the information on “Weights” in Section 6. Refer to the manufacturer’s instructions for information on how to fit and operate the towing equipment. Please keep these instructions with the rest of the vehicle documentation. 5.
Fitting a radio 1 2 3 Radio location 1 Location for front speaker 2 Location for rear speaker 3 If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: Unclip cover 2 using a flat-blade screwdriver or similar. Unclip cover 3 using a flat-blade screwdriver or similar. – the radio 1; – front speakers 2; – rear speakers 3. To install any equipment, please consult an approved dealer. Unclip and remove storage compartment 1. 5.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Use of transmission/ receiving devices (telephones, CB equipment etc.
OPERATING FAULTS (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO Warning lights dim or fail to come on; the starter does not run. Battery terminals disconnected, oxidised or incorrectly secured. Retighten them, reconnect them or clean them if they are oxidised. Battery discharged or worn.
OPERATING FAULTS (2/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures; if this is not the cause, have their condition checked by an approved dealer. Coolant boiling in the coolant reservoir. Mechanical fault: cylinder head gasket damaged, faulty coolant pump. Stop the engine. Contact an approved dealer. Engine cooling fan not working. Contact an approved dealer.
OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO Abnormal white smoke from the exhaust Mechanical fault: damaged cylinder head gasket. Stop the engine. Contact an approved dealer. or The power-assisted steering becomes heavy. This is not necessarily a fault. Smoke may be caused by regeneration of the particle filter. Refer to the information on “Special features of diesel versions” in Section 2. Belt broken. Have the belt replaced.
OPERATING FAULTS (4/5) On the road POSSIBLE CAUSES WHAT TO DO Whistling Roof aerial poorly positioned. Position the aerial. The engine overheats. The coolant temperature indicator light comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Stop the vehicle, switch off the engine and check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
OPERATING FAULTS (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Bulb blown. Replace the bulb. The direction indicators do not work. Faulty electrical circuit. Consult an approved dealer.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weights/Towing weights . . . . . . . . . .
VEHICLE IDENTIFICATION PLATES A 1 2 3 4 5 A XXXXX xx x 11 12 13 Quote the details given on identification plate A on all letters or orders. Vehicle identification plate A permissible all-up 3 Total train weight (vehicle fully loaded, with trailer). 4 Maximum permissible weight on front axle. 5 Maximum permissible weight on rear axle. 6.2 6 Technical specifications of the vehicle. 7 Vehicle paint reference. 1 Vehicle type and chassis number. 2 Maximum weight. 6 7 8 9 10 8 Equipment level.
ENGINE IDENTIFICATION plates B 1 2 B 3 B The information shown on the vehicle identification plate should be quoted on all correspondence or orders. B – Engine plate or engine label (Location varies depending on engine) 1 Engine type 2 Engine suffix 3 Engine number B B 6.
ENGINE SPECIFICATIONS Versions Engine type (see engine plate) Cubic capacity (cc) Type of fuel Octane rating 1.2 16V 1.4 1.6 1.6 16V 1.5 dCi D4F K7J K7M K4M K9K Turbo 1,149 1,390 1,598 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. If not available, for a limited time only, use unleaded fuel: – with an octane rating of 91 for a label with the ratings 95 or 98; – with an octane rating of 87 for a label showing 91, 95 or 98.
DIMENSIONS (in metres) 0.781 2.589 0.650 1.480 - 1.494 0.785 2.588 0.651 1.746 - 1.753 4.020 - 4.024 1.534(*) 1.546(*) 1.470 - 1.483 (*) Unladen 6.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
SPARE PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
Anticorrosion check (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/4) A ABS......................................................................... 2.12 – 2.13 accessories........................................................................ 5.33 accessories - installation.................................................... 5.33 accessories socket............................................................. 3.14 adjusting your driving position.......................1.11 → 1.14, 3.17 advice on antipollution...........................................
Alphabetical index (2/4) engine oil grade........................................................... 4.5 – 4.6 engine specifications............................................................ 6.4 environment.......................................................................... 2.9 F faults operating faults.................................................5.34 → 5.38 filter..................................................................................... 4.10 air filter................................
Alphabetical index (3/4) lights.......................................................................1.49 → 1.51 additional...................................................................... 5.15 adjustment.................................................................... 1.51 lights: adjusting....................................................................... 1.51 brake lights........................................................ 5.16 – 5.17 dipped beam headlights...............................
Alphabetical index (4/4) storage compartments............................................. 3.15 – 3.16 sun visor............................................................................. 3.13 T tailgate....................................................................... 3.19, 3.21 tanks and reservoirs brake fluid....................................................................... 4.7 coolant............................................................................ 4.
( www.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
