Renault MASTER Vehicle user manual
A passion for performance ELF, partner of RENAULT recommends ELF Partners in cutting-edge automotive technology, Elf and Renault combine their expertise on both the racetrack and the city streets. This enduring partnership gives drivers a range of lubricants perfectly suited to Renault cars. Lasting protection and optimum performance for your engine – guaranteed.
Welcome to your new vehicle This driver’s handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving 2 ................................................................... Your comfort ......................................................... 3 Maintenance ......................................................... 4 Practical advice .................................................... ...................................... 6 ...............................................
0.
Section 1: Getting to know your vehicle Key, remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hands-free access transmitter/receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locking/unlocking the doors . . . . . . . . . .
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/3) B A 3 2 3 2 1 1 Driver’s responsibility when parking or stopping the vehicle 4 Radio frequency remote control A Radio frequency remote control B 1 Locking all the opening elements. 1 Locking all the opening elements. 2 Unlocking all the opening elements. 3 Key for ignition switch, doors and fuel filler cap. 4 Locking/unlocking the luggage compartment and, depending on the vehicle, the sliding side doors.
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/3) C D 3 2 2 1 Radio frequency remote control operating range 3 5 5 1 Note: on certain vehicles, if a door is not opened within approximately 2 minutes of the door being unlocked by remote control, the doors will lock again automatically. 6 Radio frequency remote control C 1 Locking all the opening elements. 2 Unlocking all the opening elements. 3 Key for ignition switch, doors and fuel filler cap.
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (3/3) E Hands-free access transmitter/receiver E This enables the vehicle doors to be locked/unlocked without using the remote control unit. Refer to the information on “Hands-free access transmitter/receiver: use” in section 1. 1.4 Replacement, additional remote control or transmitter/receiver You must only contact an approved Dealer.
KEY, RADIO FREQUENCY REMOTE CONTROL: use (1/2) A B To lock/unlock the doors from inside, refer to the information on “Central door locking/unlocking” in section 1. 1 1 2 Remote controls A and B are used to lock and unlock the doors. They are powered by a battery which must be replaced (refer to the information on the “Key/radio frequency remote control: batteries” in section 5). Locking the doors Pressing button 1 locks the doors and tailgate.
KEY/RADIO FREQUENCY REMOTE CONTROL: use (2/2) Unlocking the doors C D Pressing button 2 unlocks the doors and tailgate. 1 A short press on button 3 locks/unlocks the tailgate and, depending on the vehicle, the sliding side doors. The hazard warning lights and side in- dicator lights flash once to indicate that the doors have unlocked. 1 2 2 3 Remote controls C and D are used to lock and unlock the doors and the luggage compartment.
DEADLOCKING 1 1 1 2 If fitted to the vehicle, this allows the doors to be locked and prevents them from being opened with the interior handles (for example, by breaking the window and then trying to open the doors from the inside). To activate deadlocking Press button 1 twice in quick succession. The side indicator lights and hazard warning lights flash five times to indicate that the doors have locked. To deactivate deadlocking Unlock the vehicle using button 2.
HANDS-FREE ACCESS TRANSMITTER, RECEIVER: use (1/2) 1 2 2 Driver’s responsibility when parking or stopping the vehicle 2 For vehicles equipped with transmitter/ receiver 1, in addition to the functions of the remote control, it can be used to lock/unlock without using the remote control locking unit when it is in access zone 2. Note: the hands-free access transmitter/receiver only works with the front doors and the tailgate. 1.
HANDS-FREE ACCESS TRANSMITTER, RECEIVER: use (2/2) 2 2 3 4 2 Interference Unlocking the vehicle Locking the vehicle Interference by factors in the immediate vicinity (external installations or the use of equipment operating on the same frequency as the remote control) may affect the operation of the remote control. With the transmitter/receiver in one of the access zones 2, press button 3 or 4, and all the doors will unlock.
CENTRAL DOOR LOCKING, UNLOCKING Locking the opening elements without the remote control 1 Interior locking/unlocking door control This enables all the doors to be locked simultaneously. Lock or unlock the doors by pressing switch 1. If a door or the tailgate is open or not closed properly, the doors and tailgate lock/unlock quickly. 1.10 With the engine off, the rear doors closed and a front door open, press switch 1 for more than five seconds.
MANUAL DOOR LOCKING, UNLOCKING 3 1 2 Manual control Locking the doors manually Using the key Lock or unlock the doors equipped with locks by inserting the key fully into lock 1, then turning it. With the door open, turn screw 2 (using the end of the key) or press button 3 and close the door. This means that the doors are then locked from the outside. The doors may then only be opened from inside the vehicle or with the key for the front doors. 1.
RAID (AUTOMATIC LOCKING WHEN DRIVING) To deactivate With the ignition on, press and hold switch 1 for approximately 5 seconds, until you hear a beep. The indicator light in the switch goes out. Operating principle 1 When the engine is started, the system automatically locks the doors when the vehicle reaches a speed of approximately 4 mph (7 km/h). Operating faults You can decide whether you want to activate this function.
FRONT DOORS (1/2) 4 5 1 2 3 6 Opening the doors from the outside Unlock a door equipped with lock 2 using the key. Vehicles with a remote control Pull handle 1. Opening from the inside Pull handle 6 and open the door. Closing from the inside Pull the door using only handle 5. Vehicles with a transmitter/receiver Press button 3 and pull handle 1. Closing from the outside Push the door.
FRONT DOORS (2/2) Manual locking With the door closed, lock the door by pressing button 4. NOTE The front door mechanism cannot be locked if the door is open. Lights-on reminder buzzer If you have switched off the ignition and left the lights switched on, a reminder buzzer will sound when a door is opened. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time.
SLIDING SIDE DOOR (1/2) Closing from the outside 1 Pull handle 1 and slide the door towards the front of the vehicle until it closes completely. Lock with the key or using the remote control. 2 3 Closing from the inside Pull lever 2 towards the front and close the door until it latches. Manual locking from inside Lower button 3. Opening the doors from the outside Unlock the lock with the key or with the remote control, if the vehicle is equipped with this function.
SLIDING SIDE DOOR (2/2) Recommendations concerning the sliding side door. 4 Care must be taken when opening or closing the sliding door, as is the case for any of the opening elements on the vehicle: – Check that the door will not come into contact with any person, part of the body, animal or object. – Only use the handles on the inside and outside of the door to operate it. Child locks With the door open, turn lever 4 and close the door. This means that the door is then locked from the inside.
REAR DOORS (1/2) 5 2 1 4 1 7 3 Opening the doors from the outside Unlock lock 1 using the key or, on equipped vehicles, use the remote control or the hands-free access remote control by pressing button 3. Pull handle 2 towards you and open the door. Do not leave the hinged rear doors open in case of strong winds. Risk of injury. 6 Lower lever 4 to open the door. Opening the doors to 180° Open the door, but not fully. Remove tie rod 7 from its housing 5. Lock the tie rod on the hook 6.
REAR DOORS (2/2) 9 6 7 8 A 10 B A B Opening the doors to 270° Opening from the inside Closing from the inside Remove the check-strap from its housing as when opening to 180°. Open the door fully until the magnets 6 make contact. Lower lever 7 and push door A. Partially close door B, then slam it shut. Pull lever 8 and open door B. Do the same with door A using handle 9. Locking/unlocking Closing from the outside Turn button 10. Partially close the left-hand door, then slam it shut.
STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering With the engine running, do not leave the steering wheel at full lock while stationary as this may damage the powerassisted steering pump. 1 Steering wheel height adjustment Pull lever 1 and move the steering wheel to the required position. Then, push the lever back fully, beyond the point of resistance to lock the steering wheel. Make sure that the steering wheel is correctly locked.
HEADRESTS 1 A B 2 To raise the headrest To refit the headrest Simply slide it up. Insert the rods into the holes, with the notches to the front, and lower the headrest to the desired height by pressing tab 1. To lower the headrest Press tab 1 and lower it at the same time. To remove the headrest Raise the headrest then press tabs 1 and 2 to release it. 1.20 Adjusting the angle of the headrest (depending on the vehicle) Move section B towards or away from you to the required position.
FRONT SEATS (1/3) Heated seats (depending on the vehicle) With the ignition on, press switch 5. The integrated indicator comes on. 3 4 1 A 2 Adjusting seat A To move forwards or backwards Lift handle 1 to release. Release the handle once the seat is in the correct position and ensure that the seat is locked. To adjust the height of the seat base Lower or pull lever 2 as many times as is necessary to raise or lower the seat base.
FRONT SEATS (2/3) Heated seats (depending on the vehicle) With the ignition on, press switch 8. The integrated indicator comes on. 7 The system, which has a thermostat, decides whether or not the heating is needed. B 6 11 10 9 8 12 13 Adjusting seat B with suspension Lumbar adjustment To move forwards or backwards Lift handle 11 to release. Release the handle once the seat is in the correct position and ensure that the seat is locked. Press switch 13 to make it less firm.
FRONT SEATS (3/3) To pivot the seats 19 14 C 16 15 Adjusting pivoting seats C To move the seat forwards or back Move handle 15 to unlock it. Release the handle once the seat is in the correct position and ensure that the seat is locked. To move the seat forwards or back Lift handle 18 to move the seat base forwards or back. 18 17 22 21 20 Adjusting the angle of the seat base Move handle 16 to adjust the angle of the seat base. Adjusting the height of the armrests Turn control knob 17 or 19.
SEAT BELTS (1/3) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Seat belts which are incorrectly adjusted or twisted may cause injuries in the event of an accident. Use one seat belt per person, whether child or adult.
SEAT BELTS (2/3) 6 7 1 A 3 5 5 Seat with armrest(s) Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3). Ensure the seat belt is passed underneath armrest 6, check that buckle 3 is fastened in catch 5. If there is still a problem, contact an approved dealer. If the driver’s seat belt is not fastened the light remains lit when the vehicle is started, then when the car reaches a speed of about 9.
SEAT BELTS (3/3) 8 – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident. – Never wear the shoulder strap under your arm or behind your back.
REAR SEAT BELTS Lap belts with manual adjustment 5 1 1 6 2 The strap should be worn flat over your thighs and against your pelvis. The belt should be worn so that it is as close as possible to your body, i.e. avoid wearing heavy clothing or keeping bulky objects under the belts, etc. To tighten, pull on free section 6 of the belt. To slacken, turn adjusting buckle 4 so it is at 90 degrees to the belt and press the buckle while pulling lap belt 5.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) Depending on the vehicle, they are composed of: – Have the entire restraint system checked following an accident. – seat belt pretensioners; – chest-level load limiters; – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – air bags for driver and front passenger.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Driver and passenger front airbags It is fitted to the front seats on the driver’s side and, depending on the vehicle, on the passenger’s side as well. Depending on the vehicle, an “air bag” marking on the steering wheel and the dashboard (air bag area A) indicates that this device is fitted.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is deployed and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag deploys. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
SIDE PROTECTION DEVICES Side air bags These air bags may be fitted to the front seats and are deployed at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Warnings concerning the side air bag – Fitting seat covers: seats equipped with an air bag require covers specifically designed for your vehicle. Contact an approved Dealer to find out if these covers are available.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. 1 The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
CHILD SAFETY: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
CHILD SAFETY: choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
CHILD SAFETY: choosing a child, baby seat mounting (1/2) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Check that the child seat has not been installed at an angle and that it is not resting against a window. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected.
CHILD SAFETY: choosing a child, baby seat mounting (2/2) 1 2 4 3 The ISOFIX anchorage points have been exclusively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other objects to these anchorage points. Check that nothing is obstructing the anchorage points. If your vehicle has been involved in a road accident, have the ISOFIX anchorage points checked and replace your child seat.
CHILD SAFETY: fitting a child seat: general information (1/2) Some seats are not suitable for fitting child seats. The diagrams on the following pages show you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
CHILD SAFETY: fitting a child seat, general information (2/2) In the rear seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will go, although without allowing it to come into contact with the child seat.
CHILD SEATS: attachment by seat belt (1/18) Two-seat van version Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child. They risk serious or even fatal injury. ³ ² Child seat attached using the belt Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. seats. 1.40 Seat not suitable for fitting child ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt.
CHILD SEATS: attachment by seat belt (2/18) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
CHILD SEATS: attachment by seat belt (3/18) Three-seat van version Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child. They risk serious or even fatal injury. ³ ² Child seat attached using the belt Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. seats. 1.
CHILD SEATS: attachment by seat belt (4/18) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
CHILD SEATS: attachment by seat belt (5/18) Double cab version Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child. They risk serious or even fatal injury. ³ ² Child seat attached using the belt Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. seats. 1.
CHILD SEATS: attachment by seat belt (6/18) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
CHILD SEATS: attachment by seat belt (7/18) The table below summarises the information already shown on the diagram on the next page, to ensure the regulations in force are respected.
CHILD SEATS: attachment by seat belt (8/18) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UF = Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt; check that it can be fitted.
CHILD SEATS: attachment by seat belt (9/18) 5-seater Combi version Child seat attached using the belt Seat which allows a child seat with “Universal” approval to be attached by a seat belt; ¬ ² Seat not suitable for fitting child seats. Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt. Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
CHILD SEATS: attachment by seat belt (10/18) 6-seater Combi version Child seat attached using the belt Seat which allows a child seat with “Universal” approval to be attached by a seat belt; ¬ ² Seat not suitable for fitting child seats. Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt. Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
CHILD SEATS: attachment by seat belt (11/18) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
CHILD SEATS: attachment by seat belt (12/18) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UF = Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt; check that it can be fitted.
CHILD SEATS: attachment by seat belt (13/18) The table below summarises the information already shown on the diagram on the next page, to ensure the regulations in force are respected.
CHILD SEATS: attachment by seat belt (14/18) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UF = Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt; check that it can be fitted.
CHILD SEATS: attachment by seat belt (15/18) 8-seater Combi version Child seat attached using the belt Seat which allows a child seat with “Universal” approval to be attached by a seat belt; ¬ ² Seat not suitable for fitting child seats. Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt. Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
CHILD SEATS: attachment by seat belt (16/18) 9-seater Combi version Child seat attached using the belt Seat which allows a child seat with “Universal” approval to be attached by a seat belt; ¬ ² Seat not suitable for fitting child seats. Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt. Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
CHILD SEATS: attachment by seat belt (17/18) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
CHILD SEATS: attachment by seat belt (18/18) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UF = Seat which only allows a forward-facing seat with “Universal” approval to be attached with a seat belt; check that it can be fitted.
CHILD SEATS: attachment using the ISOFIX system (1/12) The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
CHILD SEATS: attachment using the ISOFIX system (2/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
CHILD SEATS: attachment using the ISOFIX system (3/12) 5-seater Combi Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ² Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child.
CHILD SEATS: attachment using the ISOFIX system (4/12) 6-seater Combi Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ² Seat which does not allow a child seat to be fitted.
CHILD SEATS: attachment using the ISOFIX system (5/12) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
CHILD SEATS: attachment using the ISOFIX system (6/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
CHILD SEATS: attachment using the ISOFIX system (7/12) The table below summarises the information already shown on the diagram on the following pages, to ensure the applicable regulations are respected.
CHILD SEATS: attachment using the ISOFIX system (8/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
CHILD SEATS: attachment using the ISOFIX system (9/12) 8-seater Combi Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ² Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child.
CHILD SEATS: attachment using the ISOFIX system (10/12) 9-seater Combi Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible. ² Seat which does not allow a child seat to be fitted.
CHILD SEATS: attachment using the ISOFIX system (11/12) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
CHILD SEATS: attachment using the ISOFIX system (12/12) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
CHILD SAFETY: deactivating, activating the front passenger air bag (1/3) 2 1 1 Front passengerairbag deactivation (depending on the vehicle) Before installing a child seat on the front passenger seat: – check that the child seat can be installed on this seat; – it is essential to deactivate the airbagfor a rear-facing child seat. To deactivate the airbag: with the vehicle stationary and the ignition off, press and turn lock 2 to the OFF position. 1.
CHILD SAFETY: deactivating, activating the front passenger air bag (2/3) A A A 3 DANGER The markings on the dashboard and labels A on each side of the passenger sun visor 3 (for example, the labels shown above) will remind you of these instructions. Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child restraint system in a seat protected by an ACTIVATED front AIRBAG.
CHILD SAFETY: deactivating, activating the front passenger air bag (3/3) 2 1 1 Front passengerairbag activation Operating faults You should reactivate the airbag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact. To reactivate the airbag : with the vehicle stationary and the ignition off, press and turn the lock 2 to the ON position.
REAR-VIEW MIRRORS A B C 3 1 Interior rear view mirror The interior rear-view mirror is adjustable. When driving at night, to avoid being dazzled by the headlights of the vehicle behind: tilt the small lever 1 located behind the rear-view mirror. 4 2 Electrically-adjustable door mirrors Additional rear-view mirror 4 With the ignition on, position control 2 on: Lower the sun visor 3 to access the special mirror to increase lateral vision when manoeuvring.
DRIVER’S POSITION, LEFT-HAND DRIVE (1/2) 1 2 22 21 20 1.
DRIVER’S POSITION: LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 2 Side air vent. 9 Location for: – radio; – storage compartment. 18 Switches: – cruise control/speed limiter; – activation/deactivation of the Stop and Start function; – activation/deactivation of ECO mode; – fast idle speed; – power take-off. 3 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights.
DRIVER’S POSITION, RIGHT-HAND DRIVE (1/2) 1 2 22 1.
DRIVER’S POSITION, RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 13 Side air vent. 17 Switches: – cruise control/speed limiter; – activation/deactivation of the Stop and Start function; – activation/deactivation of ECO mode; – fast idle speed; – power take-off. 14 Side window demister. 18 Cigar lighter or accessories socket.
WARNING LIGHTS (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A Instrument panel A Warning light © means you should drive very carefully to an authorised dealer as soon as possible. Failure to follow this recommendation risks damaging your vehicle. 1.
WARNING LIGHTS (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ® STOP light This comes on when the ignition is switched on and goes out after about 3 seconds. If it comes on, possibly accompanied by other warning lights, stop soon as traffic conditions allow. Contact an approved dealer as soon as possible. Depending on the vehicle, this warning light is accompanied by a message on the instrument panel.
WARNING LIGHTS (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Emergency active brake assist Refer to the information on “Driving correction devices and aids” in Section 2. A Preheating warning light This should come on when the ignition is switched on. It indicates that the heater plugs are in operation. It goes out as soon as preheating is sufficient and the engine may be started.
WARNING LIGHTS (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Gear change indicator This lights up to advise you to change to a higher gear (up arrow) or, depending on the vehicle, a lower gear (down arrow). On display B Š‰ Electronic Stability Control warning light (ESP). There are several reasons for the warning light to come on: please refer to information on “Driver correction devices and aids” in Section 2.
DISPLAYS AND INDICATORS (1/2) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Trip computer and warning system A Refer to the information on the “Trip computer and warning system” in Section 1.
DISPLAYS AND INDICATORS (2/2) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Coolant temperature indicator 4 In normal use, the needle should be positioned before zone B. Under “intensive” operating conditions, the needle may approach this zone. The driver is not alerted unless the indicator 3 Ô light comes on or the message “ENGINE OVERHEATING” appears. 5 4 B Fuel gauge 3 Reagent gauge 5 The needle shows the fuel level.
TRIP COMPUTER: general information (1/2) a) Total mileage and trip mileage recorder; b) journey parameters: 1 2 A – – – – – – fuel consumed; average fuel consumption; current fuel consumption; estimated range with remaining fuel; distance travelled; average speed; c) distance before service; d) Reset the tyre pressure e) cruise control and speed limiter programmed speed; Trip computer and warning system A Display selection keys 1 and 2 Depending on the vehicle, this includes the following functions:
TRIP COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting 1 2 Trip mileage resetting With “trip mileage recorder” selected on the display, press button 1 or 2 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) The values showing average fuel consumption, range and average speed will become more stable and reliable the further you travel after pressing the reset button.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections 37360 KM Interpreting the display selected a) Total mileage and trip mileage recorder 7080 KM FUEL USED 26.0 L b) Journey parameters Fuel consumed since the last reset. AVERAGE 7.3 L/100 1.86 Average fuel consumption since the last reset.
TRIP COMPUTER: journey parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections CURRENT 8.6 L/100 RANGE ------ KM Interpreting the display selected Current fuel consumption This value is displayed after a speed of approximately 20 mph (30 km/h) is reached. Estimated range with remaining fuel This range takes into account the average fuel consumption since the last time the reset button was pressed.
TRIP COMPUTER: journey parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
TRIP COMPUTER: journey parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected TYRE PRESSURE ACQUISITION d) Reset the tyre pressures Please refer to the information on the “Tyre pressure loss warning” in Section 2. SPEED LIMITER 70 KM/H e) Cruise control/speed limiter programmed speed (depending on vehicle). Refer to the information on the “Cruise control/Speed limiter” in Section 2.
TRIP COMPUTER: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages TRACTION CONTROL OFF BATTERY MODE: ECONOMY OIL LEVEL CORRECT 1.90 Interpretation of messages Indicates that you have deactivated the traction control function. Indicates that vehicle accessories have been switched off to preserve the battery.
TRIP COMPUTER: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given on the following pages.
TRIP COMPUTER: warning messages These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
CLOCK AND EXTERIOR TEMPERATURE Exterior temperature 1 When the temperature is between –3°C and +3°C, the °C characters flash (indicates risk of ice formation). A With the ignition on, the time and, depending on the vehicle, the exterior temperature, are displayed on the onboard computer A. Press and hold the bottom button to enter the hour setting mode. When they flash on their own, press the top button to scroll through them.
SCREEN WASHER, WIPER (1/2) Vehicle fitted with windscreen wiper rain sensor 1 1 E 2 A B C F D A park B automatic wiper function. When this position is selected, the system detects water on the windscreen and triggers the wipers at a suitable wiping speed.
SCREEN WASHER, WIPER (2/2) 1 Efficiency of a wiper blade A B C D Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer. A longer pull will trigger three sweeps of the wipers followed, a few seconds later, by a fourth, in addition to the windscreen washer. Check the condition of the wiper blades.
EXTERIOR LIGHTING AND SIGNALS (1/5) 1 2 1 If the vehicle is parked on the hard shoulder with the tailgate open, the rear lights may be obscured. You should make other road users aware of your vehicle by using a warning triangle or other equipment specified by the road traffic regulations of the country you are driving in. 3 u Side lights Turn ring 3 until the symbol is opposite mark 2. The instrument panel will light up.
EXTERIOR LIGHTING AND SIGNALS (2/5) Cornering lights Depending on the vehicle, if the dipped beam headlights are on when cornering, and under certain driving conditions (speed, steering wheel angle, forwards gear selected, etc.), additional lights are switched on to light the inside of the bend. Note: under certain conditions of prolonged use, this system will switch off automatically as it is intended for use over limited periods.
EXTERIOR LIGHTING AND SIGNALS (3/5) Automatic main beam headlights Depending on the vehicle, this system switches the main beam headlights on and off automatically. The function uses a camera located behind the interior rear-view mirror to detect vehicles that are following and coming in the opposite direction.
EXTERIOR LIGHTING AND SIGNALS (4/5) Automatic main beam headlights (continued) 1 4 Operating faults When the message “CHECK LIGHTS” with warning light © is displayed e k flashes on the and warning light instrument panel, this indicates that there is a lighting fault. 5 Consult an approved dealer. Each time you start the engine, pull the stalk 1 towards you to reactivate the system. g Front fog lights Turn the centre ring 4 of the stalk 1 until the symbol is opposite the 5 mark.
EXTERIOR LIGHTING AND SIGNALS (5/5) A Load status Control position Empty, driver only 0 Driver with passenger(s) and luggage compartment full (1) 2 Other cases According to driver’s judgement The table below gives some examples. In all cases, adjust control A according to the vehicle load so that the road can be seen and other drivers are not dazzled. Electric beam height adjustment Control A allows you to adjust the height of the headlight beams.
AUDIBLE AND VISUAL SIGNALS 1 2 3 1 Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not usually turned sufficiently to return the stalk automatically to its starting position. There is an intermediate position in which you should keep the stalk when the steering wheel is moved.
FUEL TANK (1/2) Filling with fuel 1 When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made to maintain an expansion volume. Fuel grade 2 Filling the tank Open the driver’s door in order to open flap 1. Depending on the vehicle, unlock cap 2 using the key. It is essential to use diesel. Make sure that no water enters the fuel tank accidentally during filling. The sealing system and its surrounding area must be dust-free.
FUEL TANK (2/2) 3 Vehicle fitted with the Stop and Start function To fill up with fuel, the engine must be stopped (and not on standby): stop the engine (Please See “Starting, stopping the engine” in Section 2). Running out of fuel on diesel versions After a breakdown caused by completely running out of fuel, the system must be reprimed before the engine is restarted: Fill the tank on level ground with a minimum of 5 litres of diesel. Press priming bulb 3 several times. The engine can now be restarted.
REAGENT TANK (1/7) Please ensure that you comply with the legislation of your country. It is important to remember that failure to respect regulations in force could lead to legal action being taken against the vehicle owner. 1 Operating principle The reagent is intended for diesel engines fitted with the SCR (selective catalytic reduction) system. Using the reagent reduces the quantity of nitrogen oxides in exhaust gases.
REAGENT TANK (2/7) Precautions for use In extreme cold weather conditions The tank can be filled at the pump. In other cases, it is essential to read the information shown on the reagent container (e.g. the can or bottle). In frosty weather conditions, the reagent tank should be refilled when the When filling, handle the reagent carefully. They can damage clothes, shoes, bodywork components etc.
REAGENT TANK (3/7) Depending on how the vehicle is driven, they may be displayed before the reagent gauge on the instrument panel is at minimum (refer to the information on “Displays and indicators” in section 1). 3 Alert with message on the instrument panel on display 3 Front-wheel drive and van versions Warning lights and the messages on the instrument panel 3 are displayed according to the estimated range of the remaining reagent. 1.
REAGENT TANK (4/7) Maintenance/Range The information displayed on the instrument panel may be accompanied by a beep. Indicator lights Messages What to do? - “ADBLUE LEVEL CORRECT” - - on. on. “Top Up AdBlue before 2400 km” If the message is displayed when the ignition is switched on, you have less than 1,488 miles (2,400 km) range. Fill or have an Approved Dealer fill or top up the reagent in the tank.
REAGENT TANK (5/7) System fault When the indicator lights described light up, this may be accompanied by a beep. Indicator lights and come on. Message Readings « CHECK ANTI- POLLUTION SYSTEM Indicates a fault in the system. Contact your approved dealer as soon as possible. © » Indicates a system fault and that in less than 620 miles (1,000 km) it will become impossible to restart the vehicle. These warnings are repeated: and come on.
REAGENT TANK (6/7) Maintenance/Range E D C B A 4 Gauge level Warnings What to do? Range A – – Range B Range C E A Alert with no message on the instrument panel Bus and rear-wheel drive versions The warning light is displayed according to the level of reagent indicated by the needle 4 on the instrument panel. comes on. You or an Approved Dealer should flashes for a few fill or top up the reagent tank.
REAGENT TANK (7/7) System fault When the indicator lights described light up, this may be accompanied by a beep. Indicator lights on. and © Readings c o m e Indicates a fault in the system. Contact your approved dealer as soon as possible. Indicates a system fault with a loss of engine power. Contact your approved dealer and © flash when the engine as soon as possible. is started then stay lit. 1.110 and © flash. Indicates a fault in the system.
Section 2: Driving (advice on use relating to fuel economy and the environment) Running in, ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting, stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop and Start Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN, IGNITION SWITCH Up to 900 miles (1,500 km), do not exceed 2,500 rpm or approximately 54 mph (90 km/h) in the highest gear. After completing this mileage you may drive faster, although you may only expect top performance after approximately 3,600 miles (6,000 km). Start position D If the engine fails to start at the first attempt, turn the key back before activating the starter again. Release the key as soon as the engine starts.
STOPPING, STARTING THE ENGINE Depending on the vehicle, if a gear is engaged, the message “PRESS CLUTCH + START” is displayed on the instrument panel. Press the clutch pedal. Turn the key to starter position D without depressing the accelerator pedal. Release the key as soon as the engine starts. Stopping the engine With the engine idling, turn the key to the “Stop” position St.
STOP AND START FUNCTION (1/3) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc).
STOP AND START FUNCTION (2/3) Preventing the engine from standing by Conditions for coming out of engine standby In certain situations, such as negotiating a crossroads for instance, it is possible (with the system activated) to keep the engine running so as to be ready to move off quickly.
STOP AND START FUNCTION (3/3) Special feature of the automatic engine re-start The system is automatically reactivated each time the vehicle is started (see “Starting, stopping the engine” in Section 2). Under certain conditions, the engine can restart on its own in order to guarantee your safety and comfort.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Diesel engines are fitted with an injection pump with an electronic regulator which prevents overrevving of the engine irrespective of the gear engaged. Ä If the and © warning lights come on, consult an approved dealer as soon as possible. A To avoid any faults in icy weather: – make sure that the battery is always fully charged; 1 When driving, depending on the fuel grade used, it is possible that white smoke may be emitted.
DRIVING ADVICE, ECO-DRIVING (1/4) Fuel consumption is accredited in accordance with a standard regulatory method. Identical for all manufacturers, this enables vehicles to be compared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style. To optimise fuel consumption, please refer to the following advice.
DRIVING ADVICE, ECO-DRIVING (2/4) ECO mode 3 4 ECO mode is a function which optimises fuel consumption. It acts on certain power consuming systems in the vehicle (heating, air conditioning, power-assisted steering, etc.) and on certain driving actions (acceleration, gear changing, cruise control, deceleration, etc.). Activating the function Press switch 4. The warning light in the 4 switch lights up.
DRIVING ADVICE, ECO-DRIVING (3/4) – Avoid sudden acceleration. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal. – Double declutching and accelerating before switching off are unnecessary in modern vehicles.
DRIVING ADVICE, ECO-DRIVING (4/4) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and therefore helping to preserve the environment: Tyres Advice on use – An underinflated tyre increases fuel consumption. – The use of non-recommended tyres can increase fuel consumption.
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life, which entered into force in 2015. Some parts of your vehicle have therefore been designed to facilitate future recycling. These parts are easy to remove so that they can be recovered and reprocessed by recycling companies. By virtue of its design, moderate fuel consumption and initial settings, your vehicle also conforms to current antipollution regulations.
ENVIRONMENT Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the of the manufacturer eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
GEAR LEVER 1 2 Gear lever Selecting reverse gear With the vehicle stationary, move the gear lever into neutral then into reverse. Follow the grid drawn on gear knob 1, lift ring 2 against the gear knob to select reverse gear. The reversing lights will come on as soon as reverse gear is selected (with the ignition on). An impact to the underside of the vehicle (e.g.: striking a post, raised kerb or other street furniture) may result in damage to the vehicle (e.g.: deformation of an axle).
HANDBRAKE 1 2 Handbrake To apply: Pull upwards, check that the vehicle is properly immobilised. To release: Pull the lever up slightly, press button 1 and then lower the lever to the floor. Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating, or even damage, may occur.
DRIVING CORRECTION DEVICES AND AIDS (1/8) Depending on the vehicle, this is composed of: Anti-lock braking system (ABS) – anti-lock braking system (ABS); Under heavy braking, the ABS prevents the wheels from locking, allowing the stopping distance to be managed and keeping control of the vehicle. Under these circumstances, the vehicle can be steered to avoid an obstacle whilst braking. In addition, this system can increase stopping distances, particularly on roads with low surface grip (wet ground etc.).
DRIVING CORRECTION DEVICES AND AIDS (2/8) Electronic stability program (ESC) with understeer control and traction control Electronic stability control ESC This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
DRIVING CORRECTION DEVICES AND AIDS (3/8) Driver assistance with a trailer This system helps to maintain control over the vehicle while using a trailer. It detects shaking caused by towing a trailer under certain driving conditions. Operating conditions – The towbar must be approved by an authorised dealer; – the harness must be approved by an authorised dealer; – the towbar must be connected to the vehicle.
DRIVER CORRECTION DEVICES AND AIDS (4/8) Operation While driving (at speeds of between about 9 and 62 mph (15 and 100 km/h)), if there is a risk of collision with the ve- Pressing and holding one of the buttons 3 or 4 again will reactivate the system. The message “AEBS ACTIVE” 2 is displayed and the indicator light goes out on the instrument panel. 3 hicle in front, the warning light will flash on the instrument panel in red and a beep will sound.
DRIVER CORRECTION DEVICES AND AIDS (5/8) Operating faults The warning lights and lit up on the instrument panel accompanied by the message “WARNING AEBSCHECK” indicate a system fault. Consult an approved dealer. When the system detects that the func- tion is not available, the warning light lights up on the instrument panel and stays on, with the message “WARNING AEBS DISABLED”. There are two possibilities: – The system is temporarily disrupted (for example: radar obscured by dirt, mud, snow etc.
DRIVER CORRECTION DEVICES AND AIDS (6/8) Active emergency braking Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The sensor area should be kept clean and free of any modifications in order to ensure the proper operation of the system. – The system cannot respond to small vehicles such as motorbikes or bicycles as effectively as to other vehicles.
DRIVER CORRECTION DEVICES AND AIDS (7/8) Grip control “Soft ground” mode Press switch 5: the message “VARIABLEHIGHWAY MODE” lights up on the instrument panel, accompanied If fitted on the vehicle, grip control makes it easier to control the vehicle on low grip surfaces (soft ground, etc.). by the warning light , depending on the vehicle. This position enables optimal usage on soft ground (mud, sand, dead leaves, etc.). In this position, engine speed is left under the driver’s control.
DRIVING CORRECTION DEVICES AND AIDS (8/8) Hill start assistance Depending on the gradient of the incline, this system assists the driver when starting on a hill. It prevents the vehicle from rolling backwards, depending on the slope, by automatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
TYRE PRESSURE LOSS WARNING (1/3) Resetting the standard level for the tyre pressures This should be done: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended); – after changing a wheel. 1 It should always be done after checking the tyre pressure of all four tyres when cold.
TYRE PRESSURE LOSS WARNING (2/3) Note: The standard tyre pressure cannot be less than that recommended and indicated on the door frame. 2 3 Display 4 Display 2 on the instrument panel informs you of any tyre pressure faults (flat tyre, punctured tyre, etc.). “CHECK TYRE PRESSURES” Warning light comes on, along with the message “CHECK TYRE PRESSURES”.
TYRE PRESSURE LOSS WARNING (3/3) “CHECK TYRE SENSORS” The warning light flashes for several seconds, then stays on, along with the message “CHECK TYRE SENSORS”. This message appears along with the © warning light. They indicate that at least one tyre is not fitted with sensors (e.g. emergency spare wheel). Otherwise, consult an authorised dealer. Readjustment of tyre pressures The tyre pressures must be adjusted when cold (please refer to the label located on the edge of the driver’s door).
LANE DEPARTURE WARNING (1/3) 1 Using information from the camera 1, the function warns the driver if he crosses a continuous or broken line without activating the direction indicator lights. Note: make sure the windscreen is not obscured (dirt, mud, snow, condensation, etc.). This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.
LANE DEPARTURE WARNING (2/3) To activate it, press button 2. The warning light on button 2 goes out, accompanied by a message on the instrument panel “LANE DEPARTURE WARNING ON”. 2 The function is set to notify the driver if: – the indicator light on button 2 is off; and – the vehicle speed is greater than approximately 37.2 mph (60 km/h); and – lines are detected. With the ignition on, the function is active by default. Deactivating/Activating the function To deactivate it, press button 2.
LANE DEPARTURE WARNING (3/3) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. System servicing/repairs – In the event of an impact, the camera alignment may be changed, and its operation may consequently be affected. Deactivate the function, then consult an authorised dealer.
SPEED LIMITER (1/3) The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. 1 2 3 4 6 5 2.30 Controls Switching on 1 Limit speed activation, memorisation and increase switch (+). 2 Decrease limit speed (-). 3 Switch the function to standby (with limit speed memorisation (O)). 4 Activation and recall of memorised limit speed (R). 5 Main “On/Off” switch. Press the side switch 5 .
SPEED LIMITER (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by repeatedly pressing: It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the kickdown point). – switch 1 (+) to increase speed; 1 2 – switch 2 (-) to reduce speed. Whilst the speed is being exceeded, the limit speed displayed on the instrument panel flashes.
SPEED LIMITER (3/3) Recalling the limit speed If a speed has been memorised, it can be recalled by pressing switch 4 (R). 1 2 3 4 5 Switching off the function The speed limiter function is deactivated when you press switch 5. In this case, the speed is no longer memorised. The instrument panel orange indicator light goes out, confirming that the function is deactivated. Putting the function on standby The speed limiter function is deactivated when you press switch 3 (O).
CRUISE CONTROL (1/4) The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). 1 2 3 4 5 Controls 1 Cruising speed activation, storage and increase switch (+). 2 Cruising speed decrease switch (-). 3 Switch the function to standby (with stored cruising speed) (O). 4 Activation with recall of stored governed cruising speed (R). 5 Main “On/Off” switch.
CRUISE CONTROL (2/4) Driving 1 Once a cruising speed is memorised and the cruise control function is active, you may lift your foot off the accelerator pedal. 2 6 7 5 Switching on Press switch 5 on the side showing . Indicator light 6 comes on, lit green, and the message “CRUISE CONTROL” appears on the instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed.
CRUISE CONTROL (3/4) Exceeding the cruising speed 1 2 The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator pedal: after a few seconds, the vehicle will automatically return to its set cruising speed.
CRUISE CONTROL (4/4) 1 2 3 4 Recalling the cruising speed Switching off the function If a speed is memorised, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). The cruise control function is deactivated if you press switch 5: in this case a speed is no longer memorised. With a vehicle speed above 20 mph (30 km/h), press switch 4 (R).
VEHICLE WITH OVERSPEED FUNCTION Special case: if your vehicle is fitted with the Cruise control/Speed limiter, fully depressing the accelerator pedal (beyond the kickdown point) will not allow you to exceed the overspeed function set speed (refer to the information on the “Speed limiter” in Section 2). 1 The vehicle speed may be permanently set at a fixed value depending on the vehicle or on local legislation. To adjust the value or activate/deactivate the function, consult an approved dealer.
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors, fitted in the vehicle’s rear bumper, measure the distance between the vehicle and an obstacle when reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 25 centimetres from the obstacle.
PARKING DISTANCE CONTROL (2/2) Prolonged deactivation of the system 1 You can deactivate the system permanently by pressing and holding switch 1. The warning light built into the switch remains lit constantly. Operating faults When the system detects an operating fault, a beep sounds for about 3 seconds as a warning. Consult an approved dealer The deactivated system can be reactivated by pressing and holding the switch again. Temporary deactivation of the system Press switch 1 to deactivate the system.
REVERSING CAMERA (1/2) 1 3 2 Operation Moving into reverse gear, the camera 1 located on the tailgate or, depending on the vehicle, on the rear hinged door, provides a view of the area behind the vehicle on the rear-view mirror 2 or, depending on the vehicle, on the multimedia display 3, accompanied by two moving or fixed guide lines 4 and 5. Note: make sure that the reversing camera is not obscured (by dirt, mud, snow, condensation, etc.).
REVERSING CAMERA (2/2) 4 5 C B This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. This system is initially used with the aid of several gauges (mobile for trajectory and fixed for distance). When the red zone is reached, use the bumper image to stop accurately. A The screen shows a reverse image. Dynamic gauge 4 (depending on the vehicle) This is shown in blue on the multimedia display 3.
POWER TAKE-OFF 1 Operating faults Switching off the function When the indicator light integrated into switch 1 does not come on or the power take-off is not triggered: – Depress the clutch pedal; – with the clutch pedal depressed, press switch 1 and release the clutch pedal then repeat the procedure; – or gradually release the clutch pedal. Operating the function With the vehicle stopped, the engine idling, the gearbox in neutral: – depress the clutch pedal; – press switch 1.
FAST IDLE SPEED Switching off the function The function is interrupted when: – you depress the clutch pedal and/or accelerator pedal; 1 – the sequential gearbox is not in neutral; – the vehicle speed is above 0 mph; – the ® indicator light is lit up on the instrument panel; – the © indicator light is lit up on the instrument panel; Press control 1, and the function will be activated after a few seconds. Ô – the indicator light is lit up on the instrument panel.
SELF-LOCKING DIFFERENTIAL The self-locking differential controls the torque transmitted to each rear wheel. Depending on the grip conditions on the road surface, and at low speeds (under 20 mph/30 kph), this device enables wheel torque to move automatically, thereby providing increased grip. This enables the grip potential of each wheel to be used to the fullest possible extent, thereby enabling the vehicle to run over areas with decreased grip (e.g.: work sites, muddy ground, etc.).
SEQUENTIAL GEARBOX (1/5) Operation 2 Switch on the ignition. The display on the instrument panel switches on. 1 3 4 5 Selector lever 1 Display – This allows you to shift directly from first gear to reverse gear, to select reverse gear and neutral and to change gear in manual mode. 2 Load mode – It also allows you to switch between manual and automatic modes at any time, with the engine switched on and reverse gear engaged, by moving the lever to the left.
Starting Reverse gear (vehicle stationary) Moving forwards (starting in neutral) – Brake pedal depressed. Push the selector lever towards the right and to the rear as shown on the base of the lever, and then release it. Reverse gear is engaged and the letter R appears on the display. The display indicates gears N and A. – With the brake pedal depressed, push the selector lever forwards then release it. – Release the brake pedal and accelerate gently to move forwards.
SEQUENTIAL GEARBOX (3/5) Operation in semiautomatic mode (manual) This mode can be activated at any time when driving by pushing the lever to the left. The mode is switched without shifting up a gear. You can initiate gear changes using the selector lever. To shift up a gear, push the selector lever forwards; the accelerator pedal does not have to be lifted. To shift down a gear, push the selector lever backwards; the accelerator pedal does not have to be lifted.
SEQUENTIAL GEARBOX (4/5) Operation in automatic mode Automatic mode is selected by default every time the ignition is switched on. The letter A appears on the display. The vehicle is controlled using the accelerator and the brake. Gears will change automatically at the correct moment and at a suitable engine speed because the automatic mode takes the road surface and the chosen driving style into consideration. Gears may be shifted manually in this mode.
SEQUENTIAL GEARBOX (5/5) Bleep – If you hold the vehicle on a slope for too long without applying the brakes or handbrake, you will strain the system (risk of overheating the clutch). In this case, an intermittent beeping sound will remind you that you should put your foot on the brake pedal or apply the handbrake. – Never leave the vehicle with the engine running when in gear.
2.
Section 3: Your comfort Air Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning/heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use . . . . . . . . .
AIR VENTS, air outlets (1/2) 1 2 3 7 4 3 8 7 4 3 5 6 7 1 Side window demister outlet. 5 Side air vent. 2 Side air vent. 6 Side window demister outlet. 3 Windscreen demisting vents. 7 Passenger footwell heater outlets. 4 Centre air vents. 8 Control panel. 3.
AIR VENTS, air outlets (2/2) 1 2 To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Air vent 1 or 2 To open, press on the air vent. To direct, take hold of the air vent and turn it to the required position. Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). There is a risk of damage or of fire. 3.
MANUAL AIR CONDITIONING, HEATING SYSTEM (1/3) A B C D E F F i The air flow is directed mainly towards the footwells. The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. The air flow is directed to the windscreen demisting/de-icing outlets and the side windows. This position prevents the formation of condensation. Use at the highest temperature.
MANUAL AIR CONDITIONING, HEATING SYSTEM (2/3) B This function also allows the desired comfort level to be achieved as quickly as possible. C This starts or stops air recirculation. Operating tell-tale lights up when the function is operational. In this position the air is taken from inside the passenger compartment and is recycled without letting air in from outside. Adjusting the air temperature Turn control C. Turning the control to the right increases the temperature.
MANUAL AIR CONDITIONING, HEATING SYSTEM (3/3) A The air conditioning system is used for: D – lowering the temperature inside the passenger compartment; – eliminating condensation more quickly. Note: the air conditioning does not operate if the exterior temperature is low or the ventilation speed is less than 1. Adjusting the amount of air blown into the passenger compartment Switching air conditioning on or off Turn control A from 0 to 4.
AUTOMATIC CLIMATE CONTROL (1/6) 1 2 3 12 11 10 4 9 5 6 7 8 Controls (depending on vehicle) 9 and 10 - Adjusting the air temperature. 1 - “Clear View” button to demist and de-ice the windows. 11 - Heated rear screen and/or heated door mirror de-icing. 2 - Air conditioning off button. 12 - Air recirculation control. 3 - Automatic mode. Information and advice for use 4 - Display. Refer to information on “Air conditioning: information and advice on use”. 5 and 7 - Adjusting speed.
AUTOMATIC CLIMATE CONTROL (2/6) 3 4 Only the temperature and the AUTO symbol are displayed Functions managed in automatic mode are not displayed. – press button 9 to increase the temperature; – press button 10 to decrease the temperature. 10 Automatic mode Press button 3. AUTO lights up on display 4. In most cases, the automatic climate control system ensures a comfortable temperature in the passenger compartment, while maintaining good visibility and optimising fuel consumption.
AUTOMATIC CLIMATE CONTROL (3/6) Adjusting automatic mode The system normally operates in automatic mode but you can alter the standard settings used by the system (air distribution, etc.). These options are explained on the following pages. The displayed temperature values show a comfort level. In most cases, the automatic climate control system ensures a comfortable temperature in the passenger compartment, while maintaining good visibility and optimising fuel consumption.
AUTOMATIC CLIMATE CONTROL (4/6) 3 4 6 ô ö F The air flow is directed mainly to the dashboard air vents. The air flow is directed towards all the air vents and the passenger footwells. The air flow is directed mainly towards the footwells. 8 Distribution of air in the passenger compartment There are five possible combinations for air distribution, which may be selected by pressing buttons 6 and 8 repeatedly.
AUTOMATIC CLIMATE CONTROL (5/6) 2 3 4 5 7 Rear screen and/or door mirror de-icing/demisting. Press button 11: the integrated indicator light comes on. This function allows electric demisting of the rear screen and/or the electric heated door mirrors, depending on the vehicle. To exit this function, press button 11 again. Demisting automatically stops by default.
AUTOMATIC CLIMATE CONTROL (6/6) 1 3 4 5 Air recirculation Pressing button 12 activates air recirculation (the symbol lights up on the display). During recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle. Air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.). 12 11 Clear View function Press button 1; the indicator lights in buttons 1 and 11 come on. AUTO goes out on display 4.
AIR CONDITIONING: information and operating instructions (1/2) Advice on use Fuel consumption Operating faults In some situations (air conditioning off, air recirculation activated, ventilation speed at zero or low etc.), you may notice that condensation starts to form on the windows and windscreen. You will normally notice an increase in fuel consumption (especially in town) when the air conditioning is operating.
AIR CONDITIONING: information and operating instructions (2/2) A A A Ñ Type of refrigerant fluid Type of oil in the air conditioning circuit Inflammable product Consult the driver’s handbook Maintenance Quantity of refrigerant x.xxx kg fluid present in the vehicle. The refrigerant circuit may contain fluorinated greenhouse gases. Depending on the vehicle, you will find the following information on label A affixed inside the engine compartment.
WINDOWS (1/2) 3 1 2 Electric windows With the ignition on: From the front passenger seat Press switch 3. – press the switch for the window concerned to lower it to the desired height; – lift the switch for the window concerned to raise it to the desired height. From the driver’s seat Driver’s responsibility Never leave your vehicle with the key, remote control or transmitter-receiver inside, and never leave a child, adult who is not self-sufficient or a pet, even for a short while.
WINDOWS (2/2) 1 4 One-touch electric window The one-touch mode works in addition to the operation of the electric windows described previously. It is fitted to the driver’s window and is used for lowering only. Briefly press switch 1: the window lowers completely. Pressing the switch again while the window is moving will stop its movement. Sliding rear windows Press the tab 4 and slide the window. When closing the windows, ensure that no part of the body (arm, hand, etc.
INTERIOR LIGHTING Note 1 2 3 4 Remote unlocking of the doors triggers timed lighting of the passenger compartment. If one of the front or rear doors is opened, the timed lighting will start again. Then the courtesy light and the luggage compartment light dim and go out.
SUN VISOR, GRAB HANDLE 3 1 2 Sun visor Lower sun visor 1. The sun visor can be swung round against the door window. Courtesy mirror or additional rear-view mirror 2 (depending on the vehicle) Grab handle 3 This offers support and can be held when the vehicle is being driven. Lower the sun visor to access the mirror. Special feature of the additional rear-view mirror See “Rear view mirrors” in Section 1. Do not use it for getting into or out of the vehicle. 3.
ASHTRAY, CIGAR LIGHTER, ACCESSORIES SOCKET 3 1 2 4 Ashtray 2 (depending on vehicle) This is a removable ashtray which can be placed in the cup holders. Lift the cover to open. To empty it, pull the assembly. The ashtray will come out of its housing. Accessories socket 1 and 3 (depending on vehicle) They are designed for connecting accessories with a maximum power rating of 120 Watts (voltage: 12V) which have been approved by our Technical Department.
PASSENGER COMPARTMENT STORAGE, FITTINGS (1/6) 5 1 2 3 4 Front door storage compartments Storage compartment 1 Sun visor storage 5 This can be used for storing motorway tickets, cards, etc. Storage compartment 2 Do not use it as a handle to close the door. Storage compartment 3 It can hold a 1.5 litre bottle. Storage compartment 4 3.20 Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.
PASSENGER COMPARTMENT STORAGE, FITTINGS (2/6) 6 7 9 10 11 12 13 Location for storage compartment or passenger air bag 12 Glove compartment 15 14 15 17 8 Cup holder 6, 13 and 17 These can be used to hold cups or the ashtray. Pull the handle to open it. It can hold A4 size documents, a 2 litre bottle of water etc. Depending on the vehicle, it may be ventilated and refrigerated.
PASSENGER COMPARTMENT STORAGE, FITTINGS (3/6) A 23 20 18 19 B 21 22 Token holder and card holder 19 Token holder A Card holder B This can be used for storing motorway tickets, cards, etc. Location for storage compartment or tray 20 Dashboard upper storage compartment 23 To open it, lift the handle.
PASSENGER COMPARTMENT STORAGE, FITTINGS (4/6) 26 24 25 27 Tray 25 Pull tray 25 fully towards you. Turn it and push it fully. You can use clip 24 to attach A5 format documents. To refit it, pull the table tray fully towards you, lift it up until it is horizontal and push it in fully. Upper cab storage compartment 26 and 27 Reserved for the transport of objects only. The total weight of upper cab storage compartment 27 must not exceed 5 kg.
PASSENGER COMPARTMENT STORAGE, FITTINGS (5/6) 28 29 Note: make sure the tray is put back in place correctly before lifting the back of the centre seat. Check that the back of the centre seat is properly locked. 30 31 Tray On equipped vehicles, lower the back of the centre seat by lifting control 31. The back of the centre seat has the following features: – a tray 28 which can be turned only to the driver’s side (depending on the vehicle); – a cup holder 30; – storage compartment 29.
PASSENGER COMPARTMENT STORAGE, FITTINGS (6/6) 35 33 36 34 Storage compartment 34 underneath front bench seat Storage compartment underneath rear bench seat Rear load area storage compartment 36 To access, pull tabs 33. Seat base 35 lifts up to give access to a storage compartment underneath the bench seat. Reserved for the transport of objects only. The total weight of rear load area upper storage compartment must not exceed 35 kg.
REAR BENCH SEATS (1/2) 2 1 3 Access to the rear seats Removing the bench seat Move the handle 1 backwards to lower the seat back. Lift levers 2 situated behind each bench seat. The spigots 3 protrude to indicate that the bench seat is unlocked. To return the seat to its original position, bring the seatback back into position. For safety reasons, carry out any adjustments when the vehicle is not being driven. 3.
REAR BENCH SEATS (2/2) 4 3 Refitting the rear bench seat – Position the guides 4 on the rails set back in relation to the anchorage points; – slide the bench seat forwards. The row bench seats in rows 2 and 3 are not interchangeable. Do not force them into position. Risk of damage. The bench seat will lock automatically. Check that the red spigots 3 can no longer be seen. The rear bench seats must be placed on their original anchorage points.
MULTIMEDIA EQUIPMENT 1 1 4 4 2 3 3 The presence and location of this equipment depends on the vehicle’s multimedia equipment. 1 Radio; 2 Multimedia sockets; 3 steering column control; 4 multimedia touchscreen; 5 microphone. Using the telephone To operate this equipment: please refer to the driver’s handbook. 3.28 We remind you of the need to conform to the legislation in force concerning the use of such equipment.
TRANSPORTING OBJECTS (1/2) 1 2 1 Transporting objects in the rear load area Depending on the vehicle, securing rings 1 and 2 can be used to stop transported objects from moving. The number of rings and their position may vary depending on the vehicle. The sole purpose of rings 2 is to prevent transported objects from moving. The objects must be secured to mounting rings 1 on the vehicle floor beforehand. F max: 625 daN Always position the heaviest items directly on the floor.
TRANSPORTING OBJECTS (2/2) C Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. 3 3 Towing Fitting the towing ball D Front-wheel drive, standard wheels C = 1,110 mm. Rear-wheel drive, standard wheels C = 1,760 mm. Rear-wheel drive, dual wheels C = 1,753 mm. Position the ball within the range of height D, which must be between 350 and 420 mm, with the vehicle laden.
Section 4: Maintenance Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Levels . . . . . . . . . . . . . . . . . . . . . .
BONNET (1/2) 2 1 To open the bonnet, pull handle 1. Unlocking the bonnet catch To unlock, pull control 2. Please note when working close to the engine that it may be hot. In addition, the engine cooling fan may Before performing any action in the engine compartment, the ignition must be switched off (please see the information on “Starting, stopping the engine” in Section 2). 4.
BONNET (2/2) Closing the bonnet 3 4 Ensure that the windscreen wiper blades are correctly positioned. Place stay 4 back into its holders 5, hold the bonnet in the middle and lower it to about 20 cm above the closed position, then release it. It will latch automatically under its own weight. 5 Opening the bonnet Lift the bonnet and release stay 4 from its holders 5. For your own safety, it is essential to fix the stay into retainer 3 in the bonnet.
ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. However, contact an approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. 1 Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: general information (2/2) B C Maximum engine oil level exceeded. The oil level should only be read with the dipstick as explained above. Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels. If the level exceeds the maximum level, do not start your vehicle and contact an authorised dealer. In order to prevent splashback, it is recommended that a funnel be used when topping up/filling with oil.
ENGINE OIL LEVEL : topping up, filling (1/2) Oil change 2 1 1 Service interval: refer to the Maintenance Service Booklet for your vehicle. Oil change capacity 2 Please refer to the maintenance document for your vehicle, or contact an authorised dealer. Always check the engine oil level using the dipstick, as explained previously (it should never fall below the minimum level, or be over the maximum level on the dipstick).
ENGINE OIL LEVEL : topping up, filling (2/2) Exceeding the maximum engine oil level Under no circumstances must the maximum fill level be exceeded: risk of damage to the engine and catalytic converter. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer. Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels. Never run the engine in an enclosed space as exhaust gases are poisonous.
LEVELS (1/3) Level 1 1 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI” warning line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Filling After any operation on the hydraulic circuit, a specialist must replace the fluid.
LEVELS (2/3) Frequency of checking coolant level 2 Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). 3 If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; 4 – anticorrosion protection of the cooling system. Replacement intervals Refer to the Maintenance Document for your vehicle.
LEVELS (3/3)/FILTERS 7 5 Power-assisted steering pump Level: the correct level when cold, with the engine switched off and on level ground, should be visible between the “MINI” and “MAXI” levels on the reservoir 5. For topping up or refilling with oil, use products approved by our Technical Department. 6 Special feature on vehicles fitted with a tank 6 Access to the filler cap is not accessible. Contact an approved dealer for topping up or filling.
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure loss warning system In the event of underinflation (punc- A tures, underinflation etc.), the warning light on the instrument panel comes on. Please refer to the information on the “Tyre pressure loss warning” in Section 2. For your safety, please respect the speed limit. When they need to be replaced, only tyres of the same make, size, type and profile should be used on a single axle.
TYRE PRESSURE (2/2) Tyre safety and the use of chains: please refer to the information on “Tyres” in Section 5 for servicing conditions and, depending on the version, the use of chains. A B C D E F Zone B: tyre pressures for the front wheels (non-motorway). Zone C: tyre pressures for the rear wheels (non-motorway). Zone D: tyre pressures for the front wheels (motorway). Zone E: tyre pressures for the rear wheels (motorway). Zone F: tyre pressure for the emergency spare wheel.
BATTERY A This is located behind step A and does not require maintenance. You should not open it or add any fluid. Depending on the vehicle, a system continuously checks the battery charge status. When the ignition is off, some consumers may also be switched off (dipped beam headlights, radio, ventilation, etc.). On the instrument panel, the message “BATTERY MODE: ECONOMY” appears when switched off. When the level is extremely low, the message “BATTERY LOW START ENGINE” is displayed.
BODYWORK MAINTENANCE (1/3) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences. Corrosive agents in the atmosphere – atmospheric pollution (built-up and industrial areas); – saline atmospheres (near the sea, particularly in hot weather); – seasonal and damp weather conditions (e.g.
BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or freezing temperatures. Do not scrape off mud or dirt without pre-wetting. Allow dirt to accumulate on the exterior. Allow rust to form following minor impacts. Do not use solvents not approved by our Technical Department to remove stains as this could damage the paintwork. Do not drive in snow or muddy conditions without washing the vehicle, particularly under the wheel arches and body.
BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint finish This type of paint requires certain precautions. You should do the following Wash the vehicle by hand using plenty of water, using a soft cloth or a gentle sponge. Do not do the following Use wax-based products (polishing). Rub too hard. Wash the vehicle in a roller-type car wash. Attach stickers to the paintwork (risk of leaving marks). Wash the vehicle using a high-pressure cleaning device. 4.
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit . . . . . . . . . . . .
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) 2 2 3 4 A 3 6 5 1 6 2 On equipped vehicles, this is located underneath the chassis. If the emergency spare wheel has been stored for several years, have it checked by your dealer to ensure that it is safe to use. 5.2 To remove the emergency spare wheel In some cases (puncture at the rear, vehicle with towing equipment, etc.
PUNCTURE, EMERGENCY SPARE WHEEL (2/2) 7 2 To fit a wheel Proceed in the reverse order. – place the wheel flat underneath the vehicle. The valve 7 must be facing you. Risk of losing the wheel if the correct direction for refitting the wheel is not observed; – thread the cable and the component 2 through the wheel rim; – centre the component 2 in the middle of the wheel and clip it to the wheel rim; – lift the retaining cable up as far as it will go and check the wheel is completely secure.
TOOL KIT 2 3 9 5 4 1 4 7 6 5 6 8 Location of the tool kit Tool kit 1 is located under the driver’s seat. To remove the tools, move the seat forward and fold down the seatback (please refer to the information on the “Front seats” in Section 1). Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 5.
TYRE INFLATION KIT (1/6) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/6) C 2 1 D 4 If the vehicle is parked on the hard shoulder, you must warn other road users of your vehicle’s presence with a warning triangle or with other devices as per the legislation applying to the country you are in. 3 Inflation kit C Depending on the vehicle, in the event of a puncture, use inflation kit 1 located underneath the driver’s seat. Move the driver’s seat forward and fold down the seatback to access the inflation kit. Open it.
TYRE INFLATION KIT (3/6) 6 7 8 9 5 6 To connect the compressor, open the bonnet and connect black clamp 10 to earth 6 (refer to the information on “Battery: troubleshooting” in Section 5). Then connect red clamp 11 to terminal 5. Before starting the engine, check that the handbrake is applied and the gear lever is in neutral or in position N for sequential gearboxes. 5 With the engine running, press switch 7 to start inflating.
TYRE INFLATION KIT (4/6) Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; 2 Store the kit underneath the driver’s seat. 4 3 Once the tyre is correctly inflated, remove the kit: slowly unscrew the inflation adapter 3 to prevent any product spatter and screw the tyre inflation hose 4 to the bottle opening 2 to prevent the product from escaping.
TYRE INFLATION KIT (5/6) E – unroll the hose from the container; 12 19 With the engine running and the parking brake applied, – connect the compressor hose 14 to the container’s inlet 19; 13 18 17 16 15 14 Inflation kit E Depending on the vehicle, in the event of a puncture, use the inflation kit located underneath the driver’s seat.
TYRE INFLATION KIT (6/6) 12 – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; – Put the kit away. – At the end of this initial inflation operation, air will still escape from the tyre. You must drive a short distance in order to seal the hole. – Start immediately and drive at between 12 and 40 mph (20 and 60 km/h) in order to distribute the product evenly in the tyre and, after driving for 2 miles (3 km), stop and check the pressure.
WHEEL TRIMS (1/2) 1 1 3 A B 3 C 3 2 D 3 4 Wheel trim 2 Central wheel trim 4 Remove it using hubcap tool 1 (found in the tool kit), by pushing the hook into the opening located near the valve (to reach the metal retaining wire located behind the wheel trim). Remove it using hubcap tool 1, inserting the tool into the recesses 3 provided. (concealed wheel bolts) To refit it, align it with the valve.
WHEEL TRIMS (2/2) 5 6 Wheel trim 5 Wheel trim 6 To remove it without removing the wheel, press it at the points indicated by the arrows. Remove the nut covers 6 by hand, then remove the wheel trim. (exposed wheel bolts) Turn it so that the retaining brackets holding it in place behind the wheel bolts are released. To refit the hubcap, proceed in reverse order. 5.
CHANGING A WHEEL: hydraulic jack (1/3) Undo the wheel bolts by fitting the wheel spanner 3 extended using the hexagonal extension piece 2 (supplied in the tool kit) and pressing down. 1 2 3 When removing dual wheels, unscrew inflating extension piece 1. Do not forget to reattach it when refitting. Anti-theft bolt If you use anti-theft bolts, fit these nearest the valve (otherwise it may not be possible to fit the wheel trim).
CHANGING A WHEEL: hydraulic jack (2/3) Fit the emergency spare wheel on the central hub and, depending on the vehicle, turn it to align the mounting holes in the wheel and the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. 3 2 4 Take the jack 3 out of the tool kit. Familiarise yourself with the jack arrangement prior to using it.
CHANGING A WHEEL: hydraulic jack (3/3) Have the tightening and the pressure of the spare wheel checked as soon as possible. F A G E B D C Tighten the nuts and lower the jack. With the wheel on the ground, tighten the bolts completely, following the order of tightening below: H K J I Wheel with 5 holes: start with screw G, then J, H, K and finish with I. Wheel with 6 holes: start with screw A, then D, B, E, C and finish with F. 5.
CHANGING A WHEEL: jack (1/2) 1 If the vehicle is parked on the hard shoulder, you must warn other road users of your vehicle’s presence with a warning triangle or with other devices as per the legislation applying to the country you are in. B A Switch on the hazard warning lights. Keep the vehicle away from traffic and on a level surface where it will not slip. Apply the parking brake and engage a gear (first or reverse, or N for sequential gearboxes).
CHANGING A WHEEL: jack (2/2) 3 3 5 C D G F 4 E 2 Position jack 4 horizontally. Jack head 3 must be positioned level with the reinforcement panel closest to the wheel in question or the contact points 5; start cranking the jack up by hand to align the base plate (which should be pushed slightly under the vehicle). Turn the wheelbrace a few times using the wheel spanner 2 until the wheel is lifted off the ground.
TYRES (1/3) The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 1 When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads.
TYRES (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey.
TYRES (3/3) Fitting new tyres For your safety, please respect the speed limit. When they need to be replaced, only tyres of the same make, size, type and profile should be used on a single axle. They must: either have a load capacity and speed rating at least equal to those of the original tyres, or conform to those recommended by an authorised dealer. Failure to heed these instructions could endanger your safety and affect your vehicle’s roadworthiness. Risk of loss of control of the vehicle.
HEADLIGHTS: changing bulbs (1/2) A 1 B 2 Front side lights Direction indicators Remove cover B and pull bulb holder 2. Remove cover A and turn bulb holder 1 a quarter turn. Bulb type: W5W. Note: once the bulb has been replaced, ensure the cover is refitted correctly. To refit the bulb holder, position it correctly, as determined by the foolproofing device. Bulb type: PY21W. Note: once the bulb has been replaced, ensure the cover is refitted correctly.
HEADLIGHTS: changing bulbs (2/2) Main beam headlights Remove cover C. Bulb type: H1. Note: once the bulb has been replaced, ensure the cover is refitted correctly. 5 D E Dipped beam headlights Remove cover E and turn bulb holder 6 a quarter turn. Bulb type: H7LL. Do not touch the bulb glass. Hold it by its base. Note: once the bulb has been replaced, ensure the cover is refitted correctly.
HEADLIGHTS: front fog lights 1 Fog lights 1 Consult an approved dealer. The bulbs are under pressure and can break when replaced. Any operation on (or modification to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment (harness, components and in particular the alternator). In addition, your Dealer has all the parts required for fitting these units. Risk of injury. 5.
SIDE LIGHTS: changing bulbs A B 1 3 2 Side indicator lights Clearance lights Move mirror 1 to access the bolt. Push light 3 (movement A) and press at B to release the light. Undo the bolt using a Torx screwdriver. Take out the indicator light and replace bulb 2. Bulb type, depending on vehicle: WY5W or P21W. To comply with current legislation, or as a precaution, you can obtain an emergency kit from an approved dealer containing a set of spare bulbs and fuses.
REAR LIGHTS: changing bulbs (1/2) A 4 1 3 5 2 6 1 Rear lights Depending on the vehicle, remove the protective grilles. Unscrew the two nuts 1 and pull rear light unit A. 7 Unscrew the bolt 2 using a flat-blade screwdriver or similar to remove the bulb holder 3. 4 Side lights and brake lights Pear-shaped, bayonet type P21/5W bulb with two filaments. 5 Indicator Orange pear-shaped, bayonet type PY21W bulb. 6 Reversing light Pear-shaped, bayonet type bulb P21W.
REAR LIGHTS: changing bulbs (2/2) 8 9 High-level brake light Remove cover 8. Unscrew the nut. Remove the unit, from outside the vehicle, to gain access to bulb 9. Bulb type: W16W. 10 Number plate lights Unclip light 10 (using a flat-blade screwdriver or similar). Remove the light cover to gain access to the bulb. Bulb type: W5W. 5.
INTERIOR LIGHTING: changing bulbs 1 2 3 4 Courtesy light Unclip the ceiling light diffuser 1 using a flat blade screwdriver or similar. Pull the bulb to remove it from its housing. Special features for vehicles fitted with a reading lamp Type of bulb 2: festoon 10W Type of reading lamp 3: W5W Rear lights Unclip the ceiling light diffuser using a flat blade screwdriver or similar. Pull the bulb to remove it from its housing. Bulb type: W6W Type of bulb 4 : W6W Replace the bulb and refit the lens.
FUSES (1/5) Your vehicle is equipped with two fuse boxes: in the passenger compartment and in the engine compartment. 1 A If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 1, located at the back of flap A. To remove the fuse from the tweezers, slide the fuse to the side. It is not advisable to use the free fuse locations.
FUSES (2/5) Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL) Numbers Allocation Numbers Allocation Numbers Z Brake lights, interior lighting. Cornering lights. î Radio, heated seats, multifunction display, sockets for audio and alarm connections. Ä Passenger compartment ECU. Hands-free access. ß Brake lights. £ Tachograph. y Heating and air conditioning system fan. ë Æ a N D Accessories sockets. Cigar lighter.
FUSES (3/5) 3 C 5 4 2 4 Fuses in the engine compartment Unscrew the four screws 4. To identify the fuses, refer to the fuse allocation label (see the next page for details), located on unit 5. Removing fuse box C Remove screw 2 and remove coolant reservoir 3. Please note when working close to the engine that it may be hot. The engine cooling fan may also start No operations should be carried out on the cooling circuit when the engine is hot. Risk of burns. 5.
FUSES (4/5) 5 56 3 4 C C 2 7 Refitting fuse box C Clip the mountings 7, then clip mounting 6. 4 Screw the four screws 4 to ensure that unit 5 is completely sealed. Position coolant reservoir 3, then screw bolt 2. Check that no water or dust enters unit 5 when it is being removed/refitted. 5.
FUSES (5/5) Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL) Symbol Allocation Symbol Allocation V Right-hand side light. P Right-hand main beam headlight. Y Left-hand side light. n ABS T Right-hand dipped beam headlight. f Windscreen wiper. L Left-hand dipped beam headlight. t Heating and air conditioning system. G Fog light d De-icing. Q Left-hand headlight. 5.
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (courtesy lights, etc.
BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. A The two batteries must have an identical nominal voltage of 12 volts.
RADIO FREQUENCY REMOTE CONTROL: battery A 3 2 1 Replacing the battery Open the case at slot 1 using a flatblade screwdriver or similar and replace the battery 2, observing the type and polarity shown on the back of the cover. Note: It is not advisable to touch the electrical circuit in the key cover when replacing the battery. Do not dispose of your used batteries in the countryside. Give them to an organisation that collects and recycles used batteries.
HANDS-FREE ACCESS TRANSMITTER, RECEIVER: battery 2 1 Replacing the battery Use a coin to open the unit via slot 1. Replace battery 2 according to the direction marked on the cover. Note: it is not advisable to touch the electronic circuit in the cover when replacing the battery. The batteries are available from approved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical contact. 5.
WIPER BLADES 3 4 2 5 B A Note: the step may be slippery. – press tab 3 and slide the wiper blade downwards to release hook 5 from the wiper arm; Replacing windscreen wiper blades 2 Refitting – Lift wiper arm 4; – move the blade into a horizontal position; – clean the blades and the windscreen regularly with soapy water; – do not use them when the windscreen is dry; 1 To access the wiper blades, stand on step 1. Check the condition of the wiper blades.
TOWING: breakdown (1/2) The steering wheel must be unlocked and the ignition key must be in position M (ignition on) to provide brake lights and hazard warning lights on the towed vehicle. At night the vehicle must have its lights on. Unhitch the trailer, etc., if one is being towed. You must observe the towing regulations which apply in the country in which you are driving: do not exceed the towing weight for your vehicle. Contact an approved dealer.
TOWING: breakdown (2/2) 2 3 4 1 5 Only use: Front towing point 2 – At the rear left, towing point 1. Accessing towing hitch 4 – At the front, towing hitch 4 (from the tool kit) and towing point 2. These towing points may only be used for pulling the vehicle, never for lifting it either directly or indirectly. Rear towing point 1 Move the driver’s seat forward and recline the seatback so that tool kit 3 can be removed.
FITTING THE RADIO 1 2 If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – radio 1; – front speakers 2 (depending on the vehicle). To install any equipment, please consult an approved dealer. Radio location 1 Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. 5.40 – In all cases, it is very important to follow the manufacturer’s instructions carefully.
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only. Fire hazard. When several accessory sockets are used at the same time, the total power of the connected accessories must not exceed 180 watts.
OPERATING FAULTS (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO Warning lights dim or fail to come on; the starter does not run. Battery terminals disconnected, oxidised or incorrectly secured. Contact an approved Dealer. Battery discharged or worn. Connect another battery to the faulty battery.
OPERATING FAULTS (2/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to the correct pressure, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved dealer. Coolant boiling in the coolant reservoir. Mechanical fault: damaged cylinder head gasket. Stop the engine. Contact an approved Dealer. Smoke under the bonnet. Short circuit or cooling system leak.
OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware of the level of force in the steering wheel needed to turn the wheels. Consult an approved dealer Fault with the electric assistance motor. Fault in the assistance system. The engine is overheating. The coolant temperature warning light and the STOP warning light come on. Engine cooling fan not working.
OPERATING FAULTS (4/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced; refer to the information on “Fuses” in section 5. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb.
OPERATING FAULTS (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The lights do not come on or go off. Faulty electrical circuit or control. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced; refer to the information on “Fuses” in section 5. Traces of condensation in the headlights or rear lights. Traces of condensation may be a natural phenomenon caused by variations in temperature and humidity.
Section 6: Technical specifications Vehicle identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weights . . . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION PLATES (1/2) A 1 2 3 4 5 6 7 A 10 9 8 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. Vehicle identification plate A 1 Manufacturer name. 2 EC design number or approval number. 3 Identification number. Depending on the vehicle, this information is also given on marking B. 4 MAM (Maximum Authorised Mass). 6.2 5 GTW (Gross train weight: vehicle fully loaded, with trailer). 6 MPAW (Maximim Permissible Weight) for front axle.
VEHICLE IDENTIFICATION PLATES (2/2) B C To access the vehicle type and chassis number, unclip the covers C using a flat-blade screwdriver or similar. 6.
ENGINE IDENTIFICATION PLATES A 1 2 A 3 The information on the engine plate or label A should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. A 6.
ENGINE SPECIFICATIONS Versions 2.3 dCi Engine type (see engine plate) M9T Cubic capacity (cc) 2 299 Injection Diesel Type of fuel Octane rating Diesel The label located in the fuel filler flap indicates the authorised fuels. Diesel fuel compliant with standard EN 590 contains up to 7 % fatty acid methyl ester in volume. Fuel types that meet European standards and are compatible with the engines of vehicles sold in Europe (in any other case, contact an Approved Dealer).
DIMENSIONS (in metres) (1/2) Q Z1 K C A E G D B Z H Y J F 6.
DIMENSIONS (in metres) (2/2) Complete vehicles without recent alterations Short (L1) Average (L2) Medium (L2.
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved dealer. Versions Maximum permissible all-up weight (MMAC) Total train weight Up to 3.
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
SERVICE SHEETS (1/6) VIN: .................................................................................. Date: Miles (km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Type of operation: Service □ .......................................
SERVICE SHEETS (2/6) VIN: .................................................................................. Date: Miles (km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Type of operation: Service □ .......................................
SERVICE SHEETS (3/6) VIN: .................................................................................. Date: Miles (km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Type of operation: Service □ .......................................
SERVICE SHEETS (4/6) VIN: .................................................................................. Date: Miles (km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Type of operation: Service □ .......................................
SERVICE SHEETS (5/6) VIN: .................................................................................. Date: Miles (km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Type of operation: Service □ .......................................
SERVICE SHEETS (6/6) VIN: .................................................................................. Date: Miles (km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Type of operation: Service □ .......................................
ANTICORROSION CHECK (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
6.
ALPHABETICAL INDEX (1/5) A ABS .......................................................................2.16 → 2.23 accessories........................................................................ 5.41 accessories socket ............................................................ 3.19 additional systems to the seat belts................................... 1.31 adjusting the seats............................................................. 1.24 adjusting your driving position .............................
ALPHABETICAL INDEX (2/5) engine technical specifications .................................................. 6.5 engine coolant ..................................................................... 4.9 engine oil ...................................................................4.4 → 4.7 engine oil level ..................................................1.83, 4.4 → 4.7 engine specifications ........................................................... 6.5 environment ..........................................
ALPHABETICAL INDEX (3/5) J jack ...................................................................................... 5.4 K keys ...........................................................................1.2 → 1.6 L lane departure warning ..........................................2.27 → 2.29 levels: brake fluid ...................................................................... 4.8 coolant ........................................................................... 4.9 power-assisted steering pump ......
ALPHABETICAL INDEX (4/5) remote control door locking batteries ....................................................................... 5.35 remote control door locking unit ................................1.2 → 1.6 RENAULT ANTI-INTRUDER DEVICE (RAID) ................... 1.12 replacement parts ................................................................ 6.9 reverse gear selecting .............................................................. 2.14, 2.46 running in .........................................
ALPHABETICAL INDEX (5/5) warning lights.......................... 1.78 → 1.83, 1.86 → 1.89, 1.91 washing .................................................................4.14 → 4.16 weights ................................................................................ 6.8 wheelbrace .......................................................................... 5.4 wheels (safety) ......................................................5.18 → 5.20 windows .........................................................
7.
RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
