LATITUDE DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. RENAULT engineers and technicians the research applied to Formula 1, have pooled their Benefiting skill to from create a quality lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle RENAULT card: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Headrests/Seats . . . . . . . . . . . . . . . . . . . . . . .
RENAULT card: general information (1/2) The RENAULT card is used for: 2 3 1 4 5 1 Unlocking the doors and trunk lid 2 Locking all the doors and trunk lid 3 Switching on the lighting remotely 4 Unlocking/locking the trunk lid 5 Integrated key – locking/unlocking the doors and trunk lid; – switching on the vehicle lighting remotely (refer to the following pages); – depending on the vehicle, automatically closing the electric windows and sunroof remotely (see the information on “Electric windows/Electric p
RENAULT card: general information (2/2) Using the key To use the integrated key, refer to Section 1 “Locking/unlocking the doors”. 5 6 Once you have accessed the vehicle using the integrated key, replace it in its housing in the RENAULT card, then insert the RENAULT card into the card reader to start the vehicle. Advice Avoid leaving the RENAULT card in hot, cold or humid areas. Do not store the RENAULT card in an area where it may accidentally become bent or damaged.
Remote control RENAULT card: use Locking the doors and trunk lid 1 2 3 Press locking button 2. 4 Unlocking the doors and trunk lid The hazard warning lights flash twice to indicate that the doors have locked. If a door or the luggage compartment is open or not properly closed, or if a RENAULT card is still in the reader, the doors and luggage compartment lock then quickly unlock and the hazard warning lights do not flash.
hands-free RENAULT card: use (1/3) 3 2 1 Use Unlocking the vehicle On equipped vehicles, in addition to the functions of the remote control RENAULT card, it can be used to lock and unlock without using the RENAULT card, when it is in access zone 1. With the RENAULT card in zone 1, you may unlock the vehicle by placing your hand in door handle 2; the vehicle will unlock (in some cases, you may need to pull door handle 2 twice to unlock the vehicle and open the door).
hands-free RENAULT card: use (2/3) Note: The RENAULT card must be within the vehicle’s access zone 1 to be able to lock the vehicle using the button. 4 Special note: If you wish to check that the doors are locked after locking with button 4, you have approximately three seconds to try the door handles without unlocking them. 1 Locking the vehicle There are three ways to lock the vehicle: remotely, using button 4, or using the RENAULT card.
hands-free RENAULT card: use (3/3) 5 6 Locking the vehicle (continued) Special note: Locking using the RENAULT card – a door or the trunk lid is open or not properly closed; With the doors and trunk lid closed, press button 5. The vehicle will lock. The hazard warning lights flash twice to indicate that the doors have locked.
RENAULT card: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. 1 2 3 If the vehicle is equipped with a deadlocking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside).
Opening and closing the doors (1/2) Card reminder buzzer 1 Opening from the outside With the doors unlocked, hold handle 1 and pull it towards you. In some cases, it may be necessary to pull the handle twice to open the door. 2 Opening from the inside Pull handle 2. Note: with the doors locked, if you pull the door handle, the door will be opened and the other doors will be unlocked.
Opening and closing the doors (2/2) 1 Child safety Ç Vehicle with switch 1 Press switch 1 to authorise opening of the rear doors. If the vehicle is equipped with electric rear windows, this action will also authorise their use. The indicator light in the switch lights up to confirm that the child safety function is activated. 1.
locking and unlocking the doors (1/2) Locking/unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work, or its access area will be modified: – if the RENAULT card battery is weak, flat, etc. 3 A 2 1 – if equipment operating on the same frequency as the card (mobile phones, etc.) is used; – vehicle located in a high electromagnetic radiation zone.
locking and unlocking the doors (2/2) 4 Interior locking/unlocking door control Switch 4 simultaneously controls the doors and the trunk lid. If a door or the trunk lid is open or not closed properly, after pressing switch 4, the doors and trunk lid lock/unlock quickly. If you need to transport objects with the trunk lid open, you can still lock the doors. With the engine switched off, remove the RENAULT card from the reader then press and hold switch 4 for more than 5 seconds.
automatic locking when driving 1 Activating/deactivating the function Refer to the information on “Vehicle settings customisation menu” in Section 1; “Auto door locking while driving” function: = < : function activated. Operating faults If you experience an operating fault (no automatic locking, the indicator light incorporated in button 1 does not light up when trying to lock the doors and trunk lid, etc.), firstly check that the doors and trunk lid are properly closed.
Front headrests To remove the headrest 2 A Lift the headrest to its highest position. Press button 1 and lift the headrest to release it (tilt the seatback backwards if necessary). Note: when the headrest is removed, take care not to change the positions of rods 3. 3 1 To raise the headrest Pull the headrest upwards to the desired height. To lower the headrest To refit the headrest Pull out the headrest rods 3 as far aspossible by pulling from the top.
Front seats (1/2) tion, release the lever. Ensure it is correctly locked in place. Heated seats 7 4 1 2 5 6 3 Front seats with electric control Front seats with manual control To move the seat forwards or back Move switch 2 forwards or backwards. To move the seat forwards or back Lift handle 4 and simultaneously move the seat base forwards or backwards. When in the desired position, release the handle. Ensure it is correctly locked in place.
Front seats (2/2) 8 Adjusting the lumbar support on the driver’s seat (depending on the vehicle) Lower handle 8 to increase the support and lift to decrease it. Depending on the vehicle, you may adjust the electricallycontrolled support. Refer to the information on the “Driver’s seat with massage function” in Section 1. For safety reasons, carry out any adjustments when the vehicle is not being driven.
Driver’s seat with position memory (1/2) Recalling a stored driving position Depending on the vehicle, it is possible to store three driving positions. A driving position includes the settings for the driver’s seat base and seatback and the door mirrors. With the vehicle stationary, briefly press button 1, 2 or 3 depending on the required stored driving position.
Driver’s seat with position memory (2/2) Driver’s seat with easy access This system allows the driver to access the driver’s seat more easily, as the seat automatically moves forwards or backwards. The seat moves backwards: – with the engine off, when the driver’s door is opened; – with the driver’s door open, when the engine is switched off.
Driver’s seat with massage function Driver’s seat with massage function 6 3 4 5 Adjusting the lumbar support on the driver’s seat You can increase or reduce the support by pressing the (+) or (-) button on switch 3/4/5 for the top, middle and bottom of the lumbar support respectively. – Take care not to damage the seatback with sharp objects. The air tubes incorporated in the seatback may also be damaged. – In the event of prolonged use of the massage function, you may start to feel uncomfortable.
Seat belts (1/3) Always wear your seat belt when traveling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, adjust your driving position and then have each occupant adjust their seat belt to ensure optimum protection. Adjusting your driving position Make sure that the rear bench seat is locked in position correctly so that the rear seat belts will operate efficiently. Refer to Section 3 “Rear bench seat”.
Seat belts (2/3) ß 1 5 3 4 5 Locking Slowly pull the belt from the inertia reel and push buckle 3 into catch 5 until you hear a click (check that the belt is secure by pulling buckle 3). If the seat belt locks and refuses to unwind enough to be buckled, pull firmly on the belt and then release it. Then try again. If the seat belt locks and refuses to return, pull 3 cm of the belt out slowly, then release it. It will retract automatically. Then gently pull the seat belt out of the inertia reel.
Seat belts (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. – For special operations (e.g.: fitting child seats) contact an approved Dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
Methods of restraint in addition to the front seat belts (1/4) Depending on the vehicle, they may comprise: – Have the entire restraint system checked following an accident. – seat belt inertia reel pretensioners; – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – lap belt pretensioners; – chest-level load limiters; – air bags for driver and front passenger.
Methods of restraint in addition to the front seat belts (2/4) Load limiters Above a certain level of impact force, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Air bags for driver and front passenger The driver’s air bag is on the steering wheel, and the passenger’s air bag on dashboard A. An “SRP AIR BAG” marking on the steering wheel and the dashboard (air bag area B) indicates that this device is fitted.
Methods of restraint in addition to the front seat belts (3/4) Operation This system is only operational when the ignition is switched on. In a severe frontal impact, the air bags inflate rapidly. This cushions the impact of the driver’s head and chest against the steering wheel and of the front passenger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hindered from leaving the vehicle.
Methods of restraint in addition to the front seat belts (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Methods of restraint in addition to the rear seat belts Depending on the vehicle, they are composed of: – seat belt pretensioners built into the inertia reels, – force limiter. These systems are designed to act independently or together when the vehicle is subjected to a frontal impact. There are two possibilities, depending on the force of the impact: – protection is provided by the seat belt only; – the pretensioner is triggered to rectify seat belt slack.
Side protection devices Side air bags These air bags are fitted to each front seat and, depending on the country, the rear side seats; the air bags are activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows to protect the passengers in case of a severe side impact.
additional methods of restraint All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: general information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: general information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell.
Child safety: choosing a child seat mounting (1/2) There are two child seat mounting systems: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
Child safety: choosing a child seat mounting (2/2) 1 3 The ISOFIX anchorage points have been exclusively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other objects to these fittings. Check that nothing is obstructing the anchorage points. If your vehicle has been involved in a road accident, have the ISOFIX fittings checked and replace your child seat. 2 The two rings 1 are located between the seatback and the seat base.
Child safety: fitting a child seat (1/5) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seat indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
Child safety: fitting a child seat (2/5) Child seat attached using the ISOFIX fitting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with “Universal” approval to be fitted. The anchorage points are located behind the headrests of the rear seats.
Child safety: fitting a child seat (3/5) Child seat attached using the ISOFIX fitting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with “Universal” approval to be fitted. The anchorage points are located behind the headrests of the rear seats.
Child safety: fitting a child seat (4/5) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Child safety: fitting a child seat (5/5) X = Seat not suitable for fitting child seats. U = Seat allowing a child seat with “Universal” approval to be attached by seat belt; check that it can be fitted correctly. IUF/IL = O n equipped vehicles, seat which allows a child seat with “universal/semi-universal or vehicle specific approval” to be fitted using the ISOFIX system; check that it can be fitted correctly.
child safety: deactivating and activating the front passenger air bag (1/3) 1 2 Deactivating the front passenger air bag To deactivate the air bag: when the vehicle is stationary, push and turn lock 1 to the OFF position. You must deactivate certain devices in addition to the front passenger seat belt before fitting a child seat in the front passenger seat.
child safety: deactivating and activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and label A on every side of the front passenger sun visor 3 remind you of these instructions. DANGER Since front passenger air bag triggering and the position of a rear-facing child seat are incompatible, NEVER fit a rear-facing child seat in this position unless the vehicle is fitted with a front air bag deactivation device. The child may suffer very serious injuries if the air bag inflates.
child safety: deactivating and activating the front passenger air bag (3/3) 1 2 Operating faults Activating the front passenger air bag Reactivate the front passenger air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact. To reactivate the air bag: when the vehicle is stationary, push and turn lock 1 to the ON position. With the ignition on, it is essential to ¹ check that warning light 2, is off.
Steering wheel/power-assisted steering Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
Driving position: left-hand drive (1/2) 1 2 3 4 5 6 7 8 27 26 32 31 30 29 26 28 9 10 11 12 10 17 18 25 19 24 20 21 23 22 1.
Driving position: left-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent 10 C entre air vents 23 Assisted parking brake 2 Side window demister outlets 11 D isplay of the time, temperature, radio information, navigation system information, etc.
Driving position: right-hand drive (1/2) 1 3 2 30 4 5 6 7 29 26 28 31 9 7 10 11 12 13 14 15 20 20 27 22 26 23 25 1.
Driving position: right-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent 11 I nstrument panel 22 Heating and ventilation controls 2 Side window demister outlets 12 D river’s air bag and horn location. 23 Ashtray/cigar lighter 3 Passenger air bag location 13 S talk for: – windscreen washer/wiper; – trip computer information readout control and vehicle settings personalisation menu.
warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A The instrument panel A lights up when the ignition is switched on. In some cases, the appearance of a warning light is accompanied by a message. The © warning light means you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. 1.
warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. x A Anti-lock braking system warning light (ABS). This lights up when the ignition is switched on and goes out after a few seconds. If it does not go out after the ignition is switched on, or lights up when driving, there is a fault with the ABS. Braking will then be as normal, without the ABS system. Contact your approved Dealer as soon as possible.
warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. B A © Warning light This lights up when the ignition is switched on and goes out as soon as the engine is started. It may light up in conjunction with other warning lights and/or messages on the instrument panel. It means you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. C Ú Battery charge warning light If it comes on together with the ® warning light and a beep, it indicates that the electrical circuit is overcharged or undercharged. Stop as soon as traffic conditions allow and consult an approved Dealer.
displays and indicators and the driving conditions, the correct fuel level may not be indicated, or the warning light may not come on automatically. Gear engaged indicator The gear engaged is shown on display 2. For more information, refer to the information on the “Automatic gearbox” in Section 2. 2 6 1 7 Rev counter 1 (rpm x 1000) Speedometer 5 (mph or km/h) Trip computer and warning system 2 The trip parameters and warning messages are displayed on display 2.
Trip computer and warning system (1/9) c) mileage before service; d) tyre pressure monitor; 1 2 e) cruise control/speed limiter programmed speed; f) vehicle settings customisation menu; g) on-board log, operating fault and information message readout.
Trip computer and warning system (2/9) 2 3 trip mileage resetting With “trip mileage recorder” selected on the display, press button 2 or 3 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) With one of the journey parameters selected on the display, press button 2 or 3 until the display resets. 1.
Trip computer and warning system (3/9) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections 101778 km Interpreting the display selected a) Total mileage and trip mileage recorder. 112.4 km Fuel used 25.2 L Average 7.2L/100 b) Journey parameters. Fuel used. Fuel consumed since the last reset. Average fuel consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset. 1.
Trip computer and warning system (4/9) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Current 9.4L/100 Range 160 km Distance Interpreting the display selected Current fuel consumption This value is displayed above a speed of approximately 18 mph (30 km/ h). Estimated range with remaining fuel This range takes into account the average fuel consumption since the last time the reset button was pressed.
Trip computer and warning system (5/9) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected c) Mileage before service. “Service in 1936 km/2 mo.
Trip computer and warning system (6/9) Journey parameters The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Tyre pressure 65 65 65 65 d) Tyre pressure monitor Refer to the information on the “Tyre pressure monitor” in Section 2. f) Vehicle settings customisation menu “Settings menu: press and hold” Enables certain vehicle functions to be set (instrument panel language, parking distance control, etc.).
Trip computer and warning system (7/9) Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of messages Interpreting the display selected “Battery low start engine” Indicates that the vehicle must be started to recharge the battery (eg. after the engine has been switched off for some time whilst listening to the radio). “Please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle.
Trip computer and warning system (8/9) Operating fault messages These appear with the © warning light and mean that you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
Trip computer and warning system (9/9) Warning messages These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Vehicle settings customisation menu 2 Once a line has been selected, keep pressing either button 2 or 3 to change the function: = < : function activated : function deactivated 1 3 This function, integrated into trip computer and warning system 1, allows certain vehicle functions to be activated/ deactivated and adjusted.
Clock and exterior temperature 1 Vehicles equipped with a navigation system, radio, etc. Exterior temperature indicator For vehicles equipped with a navigation system or radio, refer to the specific equipment instructions to discover the special features. Special note: Depending on the vehicle, when the exterior temperature is between –3°C and +3°C, the °C characters flash (indicates risk of black ice on the road).
rear view mirrors (1/2) D E Folding door mirrors (depending on the vehicles) A B 1 3 2 C Door mirrors Adjustment Select the door mirror using switch 3, then use button 1 to adjust it to the desired position. Heated door mirrors Mirror de-icing is carried out at the same time as rear screen de-icing. For safety reasons, carry out any adjustments when the vehicle is not being driven. 1.
rear view mirrors (2/2) Daytime driving Move lever 4 back to its daytime driving position. Rear view mirror without lever 4 The rear view mirror darkens automatically to prevent the driver from being dazzled by the vehicle behind. 4 Interior rear view mirror Its position can be adjusted. Rear view mirror with lever 4 Night driving When driving at night, to avoid being dazzled by the headlights of the vehicle behind, depress small lever 4 located behind rear view mirror.
Audible and visual signals Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 1 0 A 2 When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position in which the stalk may be held when changing lanes. When the stalk is released, it automatically returns to 0. Horn Press on the top or sides of steering wheel boss A.
Exterior lighting and signals (1/3) 2 3 Daytime running lights function 1 1 4 u Side lights Turn ring 2 on stalk 1 until the symbol is opposite mark 3. The side lights and number plate light come on. The brightness of the instrument panel and dashboard can be adjusted by turning control knob 4. If the side lights are not switched on, it is not possible to set the brightness of the instrument panel with control knob 4.
Exterior lighting and signals (2/3) 2 3 1 Special note: – If the dipped beam headlights are manually switched on and if the light is sufficient, the directional headlights will remain fixed; – If the lights come on automatically when cornering, the directional headlights will start working from the next time the vehicle corners; Switching off the lights There are two possibilities: Directional headlights (depending on the vehicle) With the dipped beam headlights on and under certain conditions (speed,
Exterior lighting and signals (3/3) f 2 3 5 1 6 Lights-on reminder buzzer If the lights are switched on after the engine is switched off, they will not go out when the driver’s door is opened. In this case, a lights-on reminder buzzer sounds to warn you that the lights are still on. g Front fog lights Turn centre ring 5 on stalk 1 until the symbol faces mark 6, then release it. An indicator light on the instrument panel then comes on.
Electrical adjustment of the dipped beam headlights Examples of positions for adjusting control A according to the load A On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
Windscreen wash and wipe (1/3) Vehicle fitted with front windscreen wiper rain sensor 1 1 E 2 A B C D Vehicle fitted with intermittent windscreen wipers – A park – B intermittent wiping The wipers will pause for several seconds between sweeps. It is possible to change the time between sweeps by turning ring 2.
Windscreen wash and wipe (2/3) Headlight washers 1 1 A B D Windscreen washer Fill the windscreen washer fluid and then activate the windscreen washer, with the engine running, to reprime the system. With the ignition on, pull stalk 1 towards you, then release. A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer. A longer pull will trigger three sweeps of the wipers followed, a few seconds later, by a fourth, in addition to the windscreen washer. 1.
Windscreen wash and wipe (3/3) 1 A B C D In icy weather, clear the windscreen before starting the wipers (risk of motor overheating). Check the condition of the wiper blades. Under all circumstances, replace the wipers as soon as they lose their efficiency. To replace the wiper blades, switch off the engine and place the stalk in position D. Refer to the information on the “Wiper blades” in Section 5. Make sure the windscreen is clean.
Fuel tank (1/2) Vehicles running on ethanolbased fuel A B 1 Useful capacity of fuel tank: – Petrol versions: approximately 70 litres; – Diesel versions: approximately 66 litres. Press the left side of switch 1 to open cover A. Fuel filler cap B is integrated into the filler pipe. For more information, refer to the information on “Filling with fuel” in the following pages.
Fuel tank (2/2) Filling with fuel Unscrew fuel filler cap B anticlockwise to open it. Insert the nozzle fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting - stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version For approximately the first 600 miles (1,000 km), do not exceed 3,000 to 3,500 rpm. Do not exceed 78 mph (130 km/h) in the highest gear, and avoid sudden acceleration, starting or stopping. For the first 900 miles (1,500 km), do not exceed 2,500 rpm. After this mileage, you may drive faster. Your vehicle will only perform optimally after approximately 3,600 miles (6,000 km). After 600 miles (1,000 km), you may drive faster.
Starting the engine (1/3) Vehicles with an automatic gearbox The lever should be in position P. For all vehicles: 1 3 – In some cases it will be necessary to move the steering wheel while pressing start button 1 to assist in unlocking the steering column; a message on the instrument panel “Turn steering wheel + START” warns of this. 2 Remote control RENAULT card When you get into the vehicle, insert the RENAULT card fully into card reader 2. To start, press button 1.
Starting the engine (2/3) What to do if the vehicle will not start If the starting conditions are not met, the messages or warning lights shown below will be displayed on the instrument panel: – “Gear lever to P”: place the gear lever in position P and start the engine; – “Apply brake + START” or “Press clutch + START”: depress the brake/ clutch pedal then press the Start/ Stop button; – “Turn steering wheel + START”: if the steering column is locked, you will need to move the steering wheel while pressing
Starting the engine (3/3) Operating faults 1 In some cases, the hands-free RENAULT card will not operate, or its access area will be modified: – when the RENAULT card battery is drained, flat battery, etc. – near to appliances operating on the same frequency as the card (monitor, mobile phone, video game, etc.); 2 – vehicle located in a high electromagnetic radiation zone. The message “Please insert keycard” is displayed on the instrument panel.
Stopping the engine Hands-free RENAULT card 1 2 Conditions for stopping the engine The vehicle must be stationary, with the gear lever at N or P (vehicles with an automatic transmission). Remote control RENAULT card With the card in reader 2, press button 1: the engine will stop. Removing the card from reader 2 locks the steering column. If the card is no longer in the reader when you press button 1, the message “No keycard Press and hold” appears on the instrument panel.
Special features of petrol versions The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
Special features of diesel versions Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check antipollution system” is displayed on the instrument Ä panel accompanied by the and © warning light; consult an approved Dealer straight away. When driving, depending on the fuel grade used, it is possible that white smoke may be emitted.
gear lever/Handbrake Handbrake To release: 1 Pull lever 4 slightly, press button 3 and then lower the lever to the floor. 3 To apply: 2 4 Selecting reverse gear Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating may occur. Vehicles with manual gearbox: follow the grid drawn on knob 1, and depending on the vehicle, lift ring 2 against the gear lever knob to select reverse.
Electronic parking brake (1/4) – with the engine switched off (eg. when the engine stalls): when a front door is opened. In this case, pull and release switch 3 to apply the electronic parking brake. 1 Automatic releasing of the electronic parking brake The brake will be released as soon as the vehicle starts and accelerates. 2 Automatic operation The electronic parking brake can be used to immobilise the vehicle when the engine is stopped by pressing button 1. In all other instances, e.g.
Electronic parking brake (2/4) To park the vehicle without applying the electronic parking brake (if there is a risk of freezing, for example): – with the engine running and the RENAULT card in reader 4, switch off the engine by pressing engine Start/Stop button 1; 1 – select a gear (manual gearbox) or position P (automatic gearbox); 4 2 3 Manual operation Brief stop Applying the electronic parking brake Pull switch 3.
Electronic parking brake (3/4) Automatic release is reactivated when the driver’s door is closed and the gear lever moved to position P or N before moving to D or R. 3 Versions with an automatic gearbox If the driver’s door is open or not properly closed, automatic release is deactivated for safety reasons if the gear lever is not at P or N (to prevent the vehicle from moving on its own). The message “Release manually parking brake” is displayed on the instrument panel.
Electronic parking brake (4/4) – If there is a fault, the © warning light on the instrument panel comes on accompanied by the message “Check parking brake”. Contact your approved Dealer as soon as possible. 3 Operating faults – If there is a fault with the connection between the braking system and the instrument panel, the message “Stop vehicle” is displayed on the instrument panel accompanied by the ® warning light and a beep.
Advice: antipollution, fuel economy and driving (1/3) By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is maintained and used correctly.
Advice: antipollution, fuel economy and driving (2/3) Ä This warning light on the instrument panel will indicate if there are any faults in the system: This lights up when the ignition is switched on and goes out when the engine is started. – If it lights up continuously, consult an approved Dealer as soon as possible; – if it flashes, reduce the engine speed until the light stops flashing. Contact your approved Dealer as soon as possible.
Advice: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² group signature.
Tyre pressure monitor (1/3) If the vehicle is equipped with the function, this system monitors the tyre pressure. The pressures must be adjusted when the tyres are cold. Refer to the information on “Tyre pressures”. 1 Operating principle Each wheel (except for the emergency spare wheel) has a sensor in the inflation valve which periodically measures the tyre pressure.
Tyre pressure monitor (2/3) Emergency spare wheel The emergency spare wheel has no sensor and cannot therefore be detected by the system. 3 4 A B D C Changing wheels around If you wish to swap the wheels around, you must consult an approved dealer to reinitialise the system.
Tyre pressure monitor (3/3) Operating faults If there are any anomalies during inflation, the following messages will appear on the instrument panel to inform you: Examples of selections “Inflate tyres for motorway” 65 65 65 65 “Adjust tyre pressure” 57 “Puncture” 54 “Tyre pressure sensors absent” “Check tyre pressure sensors” 2.20 Interpreting the display selected The tyre pressure is not suitable for the driving speed.
Driving correction devices (1/4) Depending on the vehicle, they may comprise: – the ABS (anti-lock braking system); – emergency brake assist with, depending on the vehicle, braking anticipation; – the electronic stability program ESP with understeer control and traction control ASR. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
Driving correction devices (2/4) Operating faults: – © and x lit on the instrument panel accompanied by the message “Check ABS”: this means the ABS is deactivated. Braking safety is still guaranteed. Consult an approved Dealer. – D and ® lit on the instrument panel accompanied by the message “Braking system fault”: this indicates a fault in the braking system. Stop the vehicle as soon as possible and consult an approved Dealer.
Driving correction devices (3/4) Electronic stability program ESP with understeer control and traction control ASR Electronic Stability Program (ESP) This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
Driving correction devices (4/4) The message “Traction control off” appears on the instrument panel to warn you. The ASR is an additional safety system. It is not advisable to drive with the function disabled. Correct this as soon as possible by pressing switch 1 again. 1 Operating faults When the system detects an operating fault, the © warning light appears on the instrument panel accompanied by the message “Check ESP”. In this case, the ESP and the ASR are deactivated. Consult an approved Dealer.
Cruise control - speed limiter: limiter function (1/3) 7 2 3 4 5 1 6 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. Controls 1 Main “On/Off” switch. 2 Limit speed activation, storage and increase switch (+). 3 Decrease limit speed ( - ). 4 Switch the function off (with limit speed storage) (O). 5 Activation and recall of stored limit speed (R). Switching on Press switch 1 on the side showing .
Cruise control - speed limiter: limiter function (2/3) Limited speed cannot be maintained 2 3 4 If driving up or down a steep gradient, the system is unable to maintain the limit speed: the stored speed on the instrument panel will flash and zone A light up in red to inform you of this situation. 5 A Driving Varying the limit speed When a limited speed has been stored and this speed is not reached, driving is similar to driving a vehicle without the speed limiter function.
Cruise control - speed limiter: limiter function (3/3) 7 2 3 4 5 1 6 Putting the function on standby The speed limiter function is suspended when you press switch 4 (O). In this case, the limit speed remains stored and the message “Memorised” accompanied by this speed appears on the instrument panel. Recalling the limit speed Switching off the function If a speed has been stored, it can be recalled by pressing switch 5 (R).
Cruise control - speed limiter: cruise control function (1/5) 2 3 4 5 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). This function is an additional driving aid. However, the function does not take the place of the driver.
Cruise control - speed limiter: cruise control function (2/5) 7 2 3 4 5 1 6 Switching on Press switch 1 on the side showing . Indicator light 6 comes on, lit green, and the message “cruise control” appears on the instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed.
Cruise control - speed limiter: cruise control function (3/5) Cruising speed cannot be maintained 2 3 4 5 A Adjusting the cruising speed Exceeding the cruising speed The cruising speed may be changed by pressing the following repeatedly: The cruising speed may be exceeded at any time by depressing the accelerator pedal. The cruising speed flashes on the instrument panel along with the illumination of zone A in red. – switch 2 (+) to increase the speed, – switch 3 (-) to decrease the speed.
Cruise control - speed limiter: cruise control function (4/5) 7 2 3 4 5 Putting the function on standby The function is suspended when you: – press switch 4 (O); – depress the brake pedal; – depress the clutch pedal or shift into neutral if the vehicle has an automatic gearbox. In all three cases, the cruising speed remains stored and the message “Memorised” appears on the instrument panel. Standby is confirmed when indicator light 7 goes out.
Cruise control - speed limiter: cruise control function (5/5) 7 1 6 Switching off the function The cruise control function is deactivated if you press switch 1: in this case a speed is no longer stored. The instrument panel green indicator lights 6 and 7 go out, confirming that the function is deactivated. Putting the cruise control on standby or switching it off does not cause a rapid reduction in speed: you must brake by depressing the brake pedal. 2.
Operating principle Ultrasonic sensors in the front or rear bumper measure the distance between the vehicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centimeters from the obstacle. 30254 Parking distance control (1/3) C B Parking distance indicator When this function is operating, the indicator is displayed on the instrument panel.
Parking distance control (2/3) Rear parking distance control Operation When reversing, any objects located less than approximately 1.2 metres away from the rear of the vehicle are detected and a beep is emitted. Front parking distance control (Depending on the vehicle) Operation The parking distance control system is only activated when the vehicle is driven at a speed below approximately 4 mph (6 km/h).
Parking distance control (3/3) Prolonged deactivation of the system You may permanently activate or deactivate the front or rear parking distance control separately. From the vehicle settings customisation menu (refer to the information on the “Vehicle settings customisation menu” in Section 1), select the line “Front parking sensor” or “Rear parking sensor” then activate or deactivate the system: < = : function deactivated : function activated An impact to the underside of the vehicle (e.g.
Reversing camera 1 2 C B A Operation When reversing (and up to approximately 5 seconds after shifting to another gear), a view of the surroundings to the rear of the vehicle is displayed on the navigation screen accompanied by two clearance gauges 1 and 2 (mobile and fixed). Note: make sure that the reversing camera is not obscured (by dirt, mud, snow, etc.). Mobile clearance gauge 1 (for vehicles fitted with electronic stability program) This is shown in blue on the navigation screen.
Automatic gearbox (1/3) 1 2 3 4 engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particular driving style you have chosen. Economical driving When driving, leave the lever in position D, keeping the accelerator pedal lightly depressed to ensure automatic gear changes at comparatively low engine speeds. Operation With gear lever 1 in position P, switch on the ignition.
Automatic gearbox (2/3) Driving in manual mode With the selector lever in position D, move the lever to the left. Shifting the lever repeatedly allows you to change gears manually: – To move down through the gears, push the lever backwards; – To move up through the gears, push the lever forwards. The gear selected is displayed on the instrument panel. Special cases In certain driving conditions (eg.
Automatic gearbox (3/3) Parking the vehicle Operating faults When the vehicle is stopped, move the lever to position P while keeping your foot on the brake pedal. The gearbox is in neutral and the drive wheels are mechanically locked by the driveshaft. – when driving, if the “Check auto gearbox” message appears on the instrument panel, it indicates a fault.
2.
Section 3: Your comfort Air Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fragrance diffuser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air ionizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . .
air Vents (air outlet) 1 2 3 5 6 7 8 4 9 12 10 9 11 12 1 Left-hand air vent 2 Left-hand side window demister outlets 5 Centre air vents 3 Windscreen demister outlet 7 Right-hand side window demister outlet 4 Air vents at the top of the dashboard 3.
air Vents 1 2 2 3 1 2 Air flow Direction Turn control knob 1. Right/left: move tabs 2 to the right or left. Up: maximum air flow Down: closed Up/down: move tabs 2 up or down. To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Turn control knob 3. Towards the windows: maximum air flow Towards the interior: closed Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours).
Fragrance diffuser Fragrance diffuser intensity adjustment Press button 3 to adjust the diffuser intensity. The integrated indicator light comes on to show you the intensity selected: 1 2 4 3 Controls 1 Fragrance diffuser outlet. 2 Capsule holder. 3 Fragrance diffuser intensity adjustment. 4 Fragrance selection. Selecting fragrance Press button 4 to select one of the two fragrances. The integrated indicator light comes on to show you the fragrance selected: – Left-hand capsule; – Right-hand capsule. 3.
Air ionizer – CLEAN: removes harmful matter from the air (bacteria, dust, etc.); – RELAX: provides a clean and relaxing driving environment by emitting ions; – Stop (all the integrated indicator lights go out). 1 Selecting the operating mode With the air conditioning on, press button 1 to select one of the three following modes. The integrated indicator light comes on to show you the mode selected: 3.
Automatic climate control (1/6) 1 2 3 4 5 6 Automatic modes 7 The automatic climate control system guarantees comfort in the passenger compartment and good visibility (except in the event of extreme conditions), whilst optimising consumption. 16 17 15 14 13 12 11 8 10 9 The controls 10 Stopping the system. 1 and 6 12 Air conditioning (on/off). (depending on the vehicle) air temperature. 2 “Clear View” function. 3, 4 and 5 Automatic programmes. 11 Ventilation speed.
Automatic climate control (2/6) 1 6 7 18 17 Adjusting the air temperature Turn control 1 to adjust the temperature on the driver’s side and control 6 for the passenger side. Special note: the highest and lowest settings allow the system to produce maximum hot or cold temperature levels (“LO” and “HI” on display 17). A 9 Adjusting the rear air temperature from the front Adjusting the rear air temperature from the rear Press button 9: the set rear temperature flashes on display A. Turn control 6.
Automatic climate control (3/6) 4 17 12 Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press button 12 to switch off the air conditioning. Where possible, it is recommended that automatic mode is used by selecting one of the automatic programmes: AUTO, SOFT or FAST. In automatic mode (indicator light for button 4 on), all heating and air conditioning functions are controlled by the system.
Automatic climate control (4/6) 2 3 4 5 Clear View function Press button 2: the integrated indicator light comes on. This function quickly demists and deices the windscreen, the rear screen, the front side windows and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-icing functions are activated automatically. 17 Press button 13 to stop the rear screen de-icer function. The integrated indicator light in button 13 will go out.
Automatic climate control (5/6) B C D 13 Rear screen de-icing/ demisting Press button 13: the integrated indicator light comes on. This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). To exit this function, press button 13 again. Demisting automatically stops by default. õ ô ó the air flow is directed towards the side window and windscreen demisting vents.
Automatic climate control (6/6) Automatic air recirculation Press button 15. The integrated indicator light comes on. The sensor located at the air intake detects atmospheric pollution, which automatically switches air recirculation on or off, depending on the ambient level of gas. Press button 15 again or press button 2 or 16 to stop this function.
Air conditioning: information and advice on use Advice on use In some situations, (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.) you may notice that condensation starts to form on the windows and windscreen. If there is condensation, use the “Clear View” function to remove it, then use the air conditioning in automatic mode to stop it forming again. If the condensation does not clear, use the FAST programme.
Electric windows and electric panoramic sunroof (1/3) These systems operate with the ignition on or off, until the driver’s door is opened. Safety of rear occupants Depending on the vehicle, the driver can disable operation of the electric windows and the rear doors by pressing switch 4. The indicator light integrated in the switch lights up to confirm that the locks have been activated.
Electric windows and electric panoramic sunroof (2/3) Special note 7 0 A B 9 C Your vehicle is equipped with an antipinch facility: when the sunroof encounters resistance whilst closing, (somebody’s fingers, etc.) it stops and then moves back several centimetres. D 8 Driver’s responsibility Sunroof blind Tilting the sunroof Check that the sunroof is closed before opening or closing the blind. To tilt: open the blind before turning control knob 9 to position A.
Electric windows and electric panoramic sunroof (3/3) Remote control window closing isation is complete, one-touch mode returns to normal operation. If necessary, contact an approved Dealer. (for vehicles with one-touch windows on all windows). When you lock the doors from the outside, press the locking button on the RENAULT card twice in quick succession, or the driver’s door button in hands-free mode, and all the windows will close automatically.
Sun visor/Sun blinds 6 1 4 2 7 5 7 5 3 Front sun visor Lower sun visor 1 over the windscreen or unclip it and turn it over side window. Courtesy mirror Slide cover 3. Depending on the vehicle, light 2 is lit. 3.16 Side sun blind Rear sun blind Pull the sun blinds upwards, holding them by tab 4 to secure them in hook 5 (check that they are securely attached). Pull the sun blinds upwards, holding them by tab 6 until hooks 7 engage in their housing (check that they are securely attached).
Interior lighting (1/3) 1 2 3 1 2 3 4 Front/rear courtesy lights Press switch 2. – Left: permanent lighting – Middle (centre position): the light comes on when you open a door and goes out a few seconds after it is closed. It also comes on for a few seconds when the engine is stopped, when the RENAULT card is removed or when the vehicle is unlocked with the RENAULT card. – Right: the light does not come on even when the door is opened.
Interior lighting (2/3) 5 6 Glove box light 5 Front footwell lights 6 Light 5 comes on when the glove box is opened. The light comes on when the door is opened and goes out a few seconds after it is closed. Light 6 also comes on for a few seconds when the engine is stopped, when the RENAULT card is removed or when the vehicle is unlocked with the RENAULT card. 3.
Interior lighting (3/3) 8 Luggage compartment light 8 Light 8 comes on when the luggage compartment is opened. 3.
Passenger compartment storage and fittings (1/4) 3 2 1 Door pockets 1 These can be used for storing books, road maps, etc. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking. 3.20 Dashboard storage compartment 2 Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.
Passenger compartment storage and fittings (2/4) 5 6 7 4 10 9 Sun visor storage 4 8 It can be used to hold motorway passes. Centre console storage compartment with two layers Centre console storage compartment Using the upper layer Press control 5 and raise armrest 7. Press control 5 and raise armrest 7. Using the lower layer Press control 8 and lift armrest 7 to lift the upper layer. (depending on the vehicle) Coin holder 9 Cup holder 10 6 Press 10 to open the cover and use the cup holder.
Passenger compartment storage and fittings (3/4) 13 14 11 15 12 Cup holder 11 Lower the central rear armrest and press 11 to allow the cup holder to be used. Central rear armrest 12 Lower the central rear armrest. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of burning if hot liquid escapes. 3.22 Clothes hooks 13 Grab handle 14 This offers support when the vehicle is moving.
Passenger compartment storage and fittings (4/4) 17 16 Rear door storage compartment 16 Front seat storage compartments 17 It can be used to hold a beverage. It can be used to hold magazines or road maps, etc. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking. 3.
Cigar lighter, Accessories socket, Ashtray 1 2 4 Cigar lighter 2 Open cover 1 by pushing it in the direction shown by the arrow. With the ignition on, push in cigar lighter 2 It will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. 8 6 3 Accessories socket 5, 6 (depending on the vehicle) The accessories socket is designed for connecting accessories with a maximum power rating of 120 Watts (voltage: 12V, 10A).
Rear headrests To refit the headrest A Insert the headrest rods into the sleeves, and lower the headrest to the first notch. Storage position A 1 Press tab 1 and lower the headrest completely. When the headrest is completely lowered (position A), this is for storage only. The headrest must be correctly adjusted when a passenger is seated. There may be adjustable headrests on the rear bench seat, depending on the vehicle. To raise the headrest Pull it upwards to the required position.
REAR BENCH SEAT 1 A 2 The seatbacks can be folded down in order to transport large objects. In all situations, lower the rear headrests (refer to the information on the “Rear headrests” in Section 3). Rear bench seat Press button 2 towards the front of the vehicle and lower seatback A For safety reasons, carry out any adjustments when the vehicle is not being driven. 3.26 To put the seatback back in position, raise it then check that it is locked correctly.
Luggage compartment 2 4 3 1 To open To close – Press the right side of switch 1 to open the trunk lid. Lower the trunk lid using handle 3 inside the trunk lid to help you. Check that the trunk lid is closed securely. – With the doors or trunk lid unlocked press button 2 and lift the trunk lid. Opening manually from inside the vehicle Special note: If it is impossible to unlock the trunk lid, it can be done from inside.
Storage compartments 1 1 Anchorage points You can secure the load using anchorage points 1. Always position objects being transported so that the heaviest items are resting against the back of the rear bench seat. Do not place any objects, especially heavy or hard objects, on the parcel shelf. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.
multimedia equipment Navigation system The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version. 1 Navigation display; 2 Radio; 3 Central control; 4 Navigation DVD reader; 5 Auxiliary input; 6 Steering column controls; 7 Microphone. Hands-free telephone integrated control 1 5 2 4 3 On equipped vehicles, use microphone 7 and steering column control 6.
Transporting objects/Towing B = 1175 mm A Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. B Transporting objects in the luggage compartment Always place the objects to be transported so that their largest side rests against the back of the rear bench seat, for normal loads (Example A), or against the back of the front seats when the rear bench seatbacks are folded down.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil change . . . . . . . . . . . . . . . . . . . . . .
Bonnet Closing the bonnet Before closing the bonnet, check that nothing has been left in the engine compartment which may prevent it from operating correctly (tools, sheets of paper, cloth, etc.) Hold the middle of the bonnet and guide it down to 30 cm above the closed position, then release. It will latch automatically under its own weight. 2 1 Opening the bonnet Pull handle 1 located on the bottom left of the dashboard. Lift the bonnet by pushing tab 2 as shown.
Engine oil level: general information (1/2) Frequency: check the oil level from time to time and always before any long journey to avoid the risk of damaging your engine. 30304 It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. 2 oil level Reading the oil level The oil level should be read with the vehicle on level ground, after the engine has been switched off for some time.
Engine oil level: general information (2/2) B B Maximum engine oil level exceeded. A A C The oil level should only be read with the dipstick as explained above. B A B B If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
Engine oil level: topping up and filling (1/3) 1 1 2 2 2.0 16V Topping up/filling The engine oil must be topped up and filled on level ground, with the engine switched off and cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Document for your vehicle. To prevent splashback, you are recommended to use a funnel to top up the oil. 2.5 V6 / 3.5 V6 – Open cap 1.
Engine oil level: topping up and filling (2/3) 1 1 1 2 1 1.5 dCi Topping up/filling The engine oil must be topped up and filled on level ground, with the engine switched off and cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Document for your vehicle. To prevent splashback, you are recommended to use a funnel to top up the oil. 4.6 1 2 2 2.0 dCi – Open cap 1.
Engine oil level: topping up and filling (3/3)/Engine oil change Oil change Service interval: refer to the Maintenance Service Document for your vehicle. Average capacities for oil change including oil filter (for information) The engine capacity depends on the power of the engine and on the associated anti-pollution regulations. 2.0 16V engine: 4.2 litres 2.5 V6 engine: 5.7 litres 3.5 V6 engine: 5.7 litres 1.5 dCi engine: 4.5 litres 2.0 dCi engine (127 kW): 7.4 litres 2.
Levels (1/3) Checking intervals 1 2 Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing – anti-corrosion protection of the cooling system Power-assisted steering oil The power-assisted steering oil level on reservoir 2 must be between the MINI and MAXI marks.
Levels (2/3) 3 Fluid level It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI” warning line on reservoir 3. If you wish to check the disc wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Topping up After any operation on the hydraulic circuit, a specialist must replace the fluid.
Levels (3/3)/filters Filters The replacement of filter elements (air filter, cabin filter, diesel fuel filter, etc.) is scheduled in the maintenance operations for your vehicle. 4 5 Windscreen/headlight washer reservoir Continuously variable transmission oil dipstick 5 Topping up Open cap 4, fill until you can see the fluid, then refit the cap. Consult an approved Dealer. Liquid Screen wash product (product with antifreeze in winter).
Battery Depending on the vehicle, the battery is in the engine compartment or in the luggage compartment. It is always maintenance-free. Depending on the vehicle, A system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the instrument panel for the duration of the charging time.
Tyre pressure A A Tyre safety and use of snow chains B C E H The tyre pressure is indicated on label A affixed to the vehicle’s body. Open the door to read it. B: dimension of the tyres fitted to the vehicle. C: tyre pressures for the front wheels (non-motorway). D F G F: tyre pressures for the rear wheels (motorway). G: tyre pressure for the emergency spare wheel. H: emergency spare wheel tyre dimension if different to the four tyres fitted to the vehicle.
Bodywork maintenance (1/2) A well-maintained vehicle will last for longer.
Bodywork maintenance (2/2) You should – Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. – Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. – Remember to visit the body shop periodically if your vehicle has an anti-corrosion warranty. Refer to the Maintenance Service Booklet. – Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit (jack - wheelbrace, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel trim. . . . . . . . . . . . . . . . .
Puncture In the event of a puncture, depending on the vehicle, you will have: An emergency spare wheel or tyre inflation kit (refer to the information on the following pages). A – – – – 5.2 Emergency spare wheel Special note: The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emergency spare wheel disappears from the instrument panel display). Refer to Section 2 “Tyre pressure monitor”. This is located in the luggage compartment.
TYRE INFLATION KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/3) 2 3 4 5 6 1 7 10 9 8 Depending on the vehicle, in the event of a puncture, use the tyre inflation kit. Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic. 5.
TYRE INFLATION KIT (3/3) 1 – – – 10 8 – Once the tyre is inflated correctly: – stop using the kit; – slowly unscrew the two inflation end pieces 8 and 10; – screw end piece 10 onto the bottle so that no product escapes; Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.
Tool kit/wheel trim - wheel 2 Towing hitch Refer to the information on “Towing” in Section 5. 1 3 Screwdriver 6 2 4 Hubcap tool This tool is used to remove the wheel trims. 5 Nut wrench 6 Wheelbrace D C 7 5 4 3 The tool kit is located under the luggage compartment carpet (tools varies depending on the vehicle). 1 Jack When replacing the jack, fold it correctly and position the wheelbrace correctly before replacing it in its position. The jack is designed for wheel changing purposes only.
Changing a wheel (1/2) Vehicles equipped with jack and wheel wrench 2 If necessary, remove the wheel trim. 1 – Undo the wheel bolts as shown by the arrow using wheelbrace 1. Position wheelbrace 1 so that you press down on it. – start cranking the jack using handle 4 to position the jack head in the centre of plate mounting 2 (which should be pushed slightly under the vehicle). – turn handle 4 several times to lift the wheel off the ground. – Position jack 3 horizontally.
Changing a wheel (2/2) – undo the bolts and take off the wheel. – fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and lower the jack.
Tyres (1/3) Tyre and wheel safety The tyres are the only point of contact between the vehicle and the road. It is therefore imperative that they are kept in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 1 When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads.
Tyres (2/3) Tyre Pressure Comply with the specified tyre pressures (including the emergency spare wheel). These must be checked at least once a month and before any long journey (refer to Section 4 “Tyre pressure”). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.2 to 0.3 bar (or 3 psi).
Tyres (3/3) Changing the position of the wheels It is strongly recommended that you do not change the position of the wheels. Use in winter Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Fitting larger tyres than the original ones will prevent chains from being fitted. Snow or Winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion.
Halogen headlights: changing bulbs Front side lights A B 1 2 3 Turn cover B a quarter turn anticlockwise, then unclip bulb holder 4, pulling it upwards to remove the bulb. Bulb type: W5W. Direction indicator lights Consult an approved Dealer. 5 The bulbs are not easy to access (requires bodywork or mechanical components to be removed) and there is a risk of injury during removal. We therefore recommend that you have your bulbs replaced by an approved Dealer.
xenon headlights: changing bulbs Front side lights A B 1 2 Turn cover B a quarter turn anticlockwise, then unclip bulb holder 2, pulling it upwards to remove the bulb. Bulb type: W5W. Direction indicator lights Consult an approved Dealer. Cleaning the headlights Because some components (the battery, its mounting) need to be removed, you are advised to have your bulbs replaced by an approved Dealer. Dipped beam headlights A Never remove cover A. Fire hazard. Dealer.
headlights: fog lights, additional lights Rear fog lights Refer to Section 5 “Rear lights and indicator lights: changing bulbs”. 1 Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved Dealer. Front fog lights 1 Changing bulbs Consult an approved Dealer. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
Rear and side lights: changing bulbs (1/3) 1 3 2 4 Direction indicator lights Remove the lights access cover by undoing 2 from inside the luggage compartment. Remove the nuts 1, release the light unit and pull the light unit to remove it. Turn bulb holder 3 a quarter turn anticlockwise, then unscrew the bulb in the same way while pressing down on it. LED brake light 4 Consult an approved Dealer. Bulb type: PY21W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
Rear and side lights: changing bulbs (2/3) 7 A 5 6 6 Reversing lights/rear fog lights. Remove the clip from the inside of the trunk lid using a flat-blade screwdriver, then pull back A. Note: take care not to break A when pulling it back. Undo bulb holder 5/6 a quarter turn anticlockwise, then remove the bulb by pulling it upwards. Reversing lights 6 Bulb type: W16W. Rear fog lights 5 Bulb type: P21W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
Rear and side lights: changing bulbs (3/3) 8 10 B 9 Number plate light 8 – Unclip light 8 by pressing tab 9 using a flat-blade screwdriver type tool. – Replace the bulb. Bulb type: W5W. Side direction indicator lights 10 Unclip indicator light 10 (using a flatblade screwdriver type tool positioned at B to move the indicator light towards the front of the vehicle). Turn the bulb holder a quarter of a turn and take out the bulb. Bulb type: WY5W. The bulbs are under pressure and can break when replaced.
Interior lights: changing bulbs (1/3) 3 1 2 Courtesy light Front door lights Courtesy mirror light 3 Unclip lens 1 using a flat-blade screwdriver type tool under the courtesy light. Unclip light 2 using a flat-blade screwdriver type tool under each side of the front door light. Unclip the light cover using a flat-blade screwdriver type tool under the cover. Remove the bulb concerned; Bulb type: W5W. When using a tool, place a cloth on the mirror to prevent scratching. Bulb type: W5W.
Interior lights: changing bulbs (2/3) 6 7 5 4 8 Glove box light 4 Luggage compartment light Consult an approved Dealer. Unclip light 5 using a flat-blade screwdriver type tool under the left-hand side of the light. Disconnect the light. Press tab 6 to release lens 8 and access bulb 7. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
Interior lights: changing bulbs (3/3) 9 Front floor lights 9 There are lights under the glove box or the steering column. Remove the bulb concerned; Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
Fuses (1/2) 1 A Fuse box If any electrical component does not work, check the condition of the fuses. Open storage compartment A, depending on the vehicle, open the glove box. Press tab 1 and pull it towards you to unclip it. Find the corresponding fuse, referring to the label at the back of storage compartment A or cover B and the fuse allocation table on the next page.
Fuses (2/2) Allocation of fuses (depending on the equipment level) The optional equipment is also marked with an asterisk “*” in the label.
Battery: troubleshooting (1/2) To avoid all risk of sparks: – Ensure that any consumers are switched off before disconnecting or reconnecting the battery. – when charging, stop the charger before connecting or disconnecting the battery. – do not place metal objects on the battery, to avoid creating a short circuit between the terminals. – Always wait at least one minute after the engine has been switched off before disconnecting a battery.
Battery: troubleshooting (2/2) 1 6 2 A 5 B 7 4 9 8 3 Starting the vehicle using the battery from another vehicle (continued) Ensure that there is no risk of contact between the two vehicles (risk of short circuiting when the positive terminals are connected) and that the discharged battery is properly connected. Switch off your vehicle ignition.
renault card: battery 2 A B 1 4 3 Replacing the battery When the message “Low card battery” appears on the instrument panel, replace the RENAULT card battery, press button 1 pulling on emergency key 2, then unclip the cover 3 using tab 4. Remove the battery by pressing on one side (movement A) and by lifting the other (movement B) then replace it, ensuring the polarity and model, shown on cover 3 are respected.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial, etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Electrical and electronic accessories Consult an approved Dealer for this information. – Connect accessories with a maximum power of 120 Watts only. Fire hazard.
WIPER BLADES E 2 1 F A B C D 4 Replacing windscreen wiper blades 2 With the ignition on and the engine switched off, lower windscreen wiper stalk 1 to position D; wiper arms 3 stop away from the bonnet. Lift wiper arm 3, press tab 4 (movement E), move the wiper blade to F after having separated it from the arm. 3 Check the condition of the wiper blades. You are responsible for their service life: – Clean the blades and the windscreen regularly with soapy water.
Towing: breakdown (1/2) Before towing, unlock the steering column: with the clutch depressed, engage first gear (lever in position N or R for vehicles with automatic transmissions), insert the RENAULT card in the card reader then press the engine start button for two seconds. Reposition the lever to neutral (position N for vehicles fitted with an automatic gearbox). The column is unlocked, the accessory functions are supplied: the vehicle lights can be used (indicators, brake lights etc.).
Towing: breakdown (2/2) When the engine is stopped, steering and braking assistance are not operational. 4 1 Only use rear towing point 1 and front towing point 4 (never use the drive shafts). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly. Towing points: precautions for use 1 3 2 Access to towing points Unclip cover 2.
Operating faults (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery. You can still lock/ unlock and start your vehicle (refer to the information on “Locking/unlocking the doors” in Section 1 and “Starting/Stopping the engine” in Section 2).
Operating faults (2/5) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are weak or fail to light up and the starter does not turn. Battery terminals not tight, battery terminals disconnected or oxidised. Retighten or reconnect the terminals, or clean them if they are oxidised. Discharged battery or not operational. Connect another battery to the faulty battery.
Operating faults (3/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved dealer. White smoke from the exhaust. This is not necessarily a fault. Smoke may be caused by regeneration of the particle filter. Refer to the information on “Special features of diesel versions” in Section 2. Smoke under the bonnet.
Operating faults (4/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine overheats. The coolant temperature indicator is in the warning zone and the ® warning light comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
Operating faults (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb. See information on “Headlights: changing the bulbs” or “Rear lights: changing the bulbs” in section 5. The direction indicators do not work.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions (in metres). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . . . . . .
Vehicle identification plates A A 1 2 3 4 5 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. B 6.2 Vehicle identification plate A 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 Maximum permissible all-up weight. 3 Total train weight (vehicle fully loaded, with trailer). 4 Front axle Maximum permissible weight. 6 7 8 9 10 11 12 13 5 Rear axle Maximum permissible weight.
Engine identification plates (1/2) C 1 C 2 3 2.0 16V The information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. C 2.5 V6 / 3.5 V6 6.
Engine identification plates (2/2) C 1 C 2 C 3 1.5 dCi 2.0 dCi The information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. C V6 dCi 6.
Dimensions (in metres) 1.035 2.762 1.100 1.565 4.897 1.492* 1.562 1.832 * Unladen 6.
Engine specifications Versions 2.0 16V 2.5 V6 3.5 V6 1.5 dCi 2.0 dCi V6 dCi Engine type (see engine plate) M4R 2ZV 5ZV K9K M9R V9X Cubic capacity (cc) 1997 2495 3498 1461 1995 2993 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Replacement parts and repairs Original RENAULT parts are based on strict specifications and are subjected to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine RENAULT parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
Anticorrosion check (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
6.
Alphabetical index (1/4) A ABS........................................................................2.21 → 2.24 accessories........................................................................ 5.26 accessories socket............................................................. 3.24 additional methods of restraint......................1.23 → 1.26, 1.29 side protection.............................................................. 1.28 to the rear seat belts................................................
Alphabetical index (2/4) engine oil level............................................................. 4.3 – 4.4 engine start/stop button..............................................2.3 → 2.6 external temperature.......................................................... 1.63 F faults operating faults.................................................5.30 → 5.34 filter..................................................................................... 4.10 fog lights..........................................
Alphabetical index (3/4) M maintenance: bodywork........................................................... 4.13 – 4.14 mechanical..........................................................6.9 → 6.14 mileage before service........................................6.9 → 6.14 map reading lights..................................................3.17 → 3.19 massage seat..................................................................... 1.19 menu for customising the vehicle settings.......................... 1.
Alphabetical index (4/4) temperature regulation.............................................3.6 → 3.11 tool kit................................................................................... 5.6 towing breakdown......................................................... 5.28 – 5.29 towing a caravan.................................................................. 6.7 towing rings........................................................................ 5.29 towing weights....................................
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
