CLIO DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... 5 . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle RENAULT card: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opening and closing the doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locking and unlocking the opening elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT CARD: general information (1/2) The RENAULT card is used for: 1 2 3 4 5 – locking/unlocking the doors and tailgate (doors, tailgate) and the fuel filler flap (see the following pages); – switch on the vehicle lighting remotely (refer to the following pages); – starting the engine; refer to the information on “Starting the engine” in Section 2. Battery life 1 Unlocking the doors and tailgate. 2 Locking all doors and tailgate. 3 Switch on the courtesy lighting remotely.
RENAULT CARD: general information (2/2) Access to key 5 Press button 6 and pull on key 5 then release the button. Using the key 5 6 Please refer to the information on “Locking and unlocking the opening elements”. Once you have accessed the vehicle using the integrated key, replace it in its housing in the RENAULT card, then insert the RENAULT card into the card reader to start the vehicle.
REMOTE CONTROL RENAULT CARD: use 2 1 3 4 Unlocking the doors and tailgate Press button 1. The hazard warning lights flash once to indicate that the doors have been unlocked. When unlocking is only active for the driver’s door, (refer to the information on the “vehicle settings customisation menu” in Section 1): – pressing button 1 unlocks only the driver’s door and the fuel filler flap; – pressing button 1 twice unlocks all the doors and the tailgate.
“Hands-free” RENAULT CARD: use (1/3) 2 3 4 1 Use On equipped vehicles, in addition to the functions of the remote control RENAULT card, it can be used to lock/ unlock without using the RENAULT card, when it is in access zone 1. Unlocking the vehicle With the RENAULT card in zone 1 and the vehicle locked, press button 3 on handle 2 on one of the two front doors: the vehicle will unlock. Pressing button 4 also unlocks all the doors and the tailgate.
“Hands-free” RENAULT CARD: use (2/3) Locking using button 3 With the doors and boot closed, press button 3 on one of the front door handles. The vehicle will lock. If a door or the boot is open or not closed properly, the vehicle will quickly lock/unlock. 3 Locking the vehicle There are three ways to lock the vehicle: remotely, using button 3, or using the RENAULT card.
“Hands-free” RENAULT CARD: use (3/3) 5 6 With the engine running, if after having opened and closed a door the card is no longer in the passenger compartment, the message Keycard not detected (accompanied by a beep when the speed exceeds a certain level) warns you that the card is no longer in the vehicle. This avoids you driving away after having dropped off a passenger who has the card, for example. The warning disappears when the card is detected again.
RENAULT CARD: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. 1 2 The hazard warning lights flash once to indicate that the doors have been unlocked. 3 4 If the vehicle is equipped with a deadlocking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside).
OPENING AND CLOSING THE DOORS (1/3) 4 1 3 2 Opening the doors from the outside Rear doors With the doors unlocked, pull handle 3. Opening from the inside Pull handle 4. Front doors With the doors unlocked, pull handle 1. Special feature of the RENAULT “hands-free” card With the doors locked, press button 2 on handle 1 of one of the two front doors and pull towards you. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. 1.
OPENING AND CLOSING THE DOORS (2/3) Lights-on reminder buzzer Door/tailgate open buzzer If you have switched off the ignition and left the lights switched on, a reminder buzzer will sound when a door is opened. If a door (or boot) is open or not properly closed, as soon as the vehicle reaches a speed of approximately 6 mph (10 km/h), the message “boot open” or “door open” (depending on which is open) will appear on the instrument panel accompanied by a warning light.
OPENING AND CLOSING THE DOORS (3/3) 5 Child safety To make it impossible for the rear doors to be opened from the inside, move lever 5 on each door and check from the inside that the doors are securely locked. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time.
Locking/unlocking the doors (1/2) Locking/Unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: 2 1 – if the RENAULT card battery is weak, flat, etc. – if equipment operating on the same frequency as the card (mobile phones, etc.) is used; – vehicle located in a high electromagnetic radiation zone.
Locking/unlocking the doors (2/2) 3 Interior locking/unlocking door control Locking the doors without the RENAULT card Door and tailgate status indicator For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc. With the ignition on, the warning light integrated in switch 3 informs you of the locking status of the opening elements: With the engine switched off and an opening element (door or boot) open, press and hold switch 3 for more than five seconds.
RENAULT ANTI-INTRUDER DEVICE (RAID) 1 Activating/deactivating the function With the engine running, press button 1 for approximately five seconds until you hear a beep. Operating faults Operating principle If you experience an operating fault (no automatic locking, the indicator light incorporated in button 1 does not light up when trying to lock the opening elements, etc.), firstly check that the opening elements are properly closed. If they are properly closed, contact an authorised dealer.
FRONT HEADRESTS To raise the headrest A 2 1 Raise the headrest to its highest position (tilt the seatback backwards if necessary). Press button 1 and lift the headrest to release it. To refit the headrest Insert the headrest rods into the holes (tilt the seatback backwards if necessary). Lower the headrest until it locks and press button 1 to adjust to the desired height. Check that each rod 2 on the seatback is securely locked. To raise the headrest Pull the headrest upwards to the desired height.
FRONT SEATS (1/3) 2 3 4 1 To move the seat forwards or backwards To raise or lower the seat base Lift handle 1 to unlock. Release the handle once the seat is in the correct position and ensure that the seat is locked. Move lever 2 as many times as necessary upwards or downwards. For safety reasons, carry out any adjustments when the vehicle is not being driven.
Front seats (2/3) To reposition the passenger seat 5 Passenger seat table formation Make sure that nothing prevents the seat from moving. – Move the seat as far back as possible; – lower the headrest as far as it will go; – hold the seatback by the top to guide it downwards, and simultaneously activate control 5 and fold the seatback forwards; – press on the back of the seatback to lock it in place. Make sure you lock the seatback properly. Make sure that nothing prevents the seat from moving.
Front seats (3/3) 5 A Central armrest 5 To adjust the armrest upwards Lift armrest to the desired position. To adjust the armrest downwards Lift the armrest to the storage position along the seat back, then lower it. 1.18 To store away the armrest Lift the armrest to the storage position A. Check that it is correctly locked.
SEAT BELTS (1/4) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Make sure that the rear bench seat is locked in position correctly so that the rear seat belts will operate efficiently.
SEAT BELTS (2/4) ß Front seat belt reminder warning light This lights up on the central display when the engine is started then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 2 minutes. 1 3 5 5 4 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3).
SEAT BELTS (3/4) 9 9 7 10 8 12 11 Rear side seat belts 7 Rear centre seat belt The belts are locked, unlocked and adjusted in the same way as the front belts. Unwind belt 9 slowly from its housing, then fasten buckle 8 into the corresponding black catch 11. Fasten sliding buckle 10 into the corresponding red catch 12. moved. Check that the rear seat belts are positioned and operating correctly each time the rear bench seat is 1.
SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they will consist of: – Have the entire restraint system checked following an accident. – front seat belt inertia reel pretensioners; – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – chest-level load limiters; – air bags for driver and front passenger.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Airbags for driver and front passenger Fitted to the driver and passenger side. The presence of this equipment is indicated by the word “Air bag” on the steering wheel and dashboard (air bag zone A) and, depending on the vehicle, a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) 4 Operation This system is only operational when the ignition is switched on. In a severe frontal impact, the air bags inflate rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and of the front passenger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hindered from leaving the vehicle.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Methods of restraint in addition to the rear side seat belts Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
SIDE PROTECTION DEVICES Side Airbags This airbag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Warning relating to the side airbag – Fitting seat covers: seats equipped with an airbag require covers specifically designed for your vehicle. Contact an approved Dealer to find out if these covers are available.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.
child safety: choosing a child/baby seat mounting (1/2) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
child safety: choosing a child/baby seat mounting (2/2) 1 2 3 5 4 The two rings 1 are located between the seatback and the seat base of the seat and are identified by a marking. The third ring 4 or 5 is used to attach the upper strap on some child seats. Rear seats The 2 belt should be positioned between the seatback and the rear parcel shelf. To do this, remove the rear parcel shelf (refer to the information on the “Rear parcel shelf” in Section 3).
child safety: fitting a child seat (1/6) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seat indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Ensure that the child seat or the child’s feet do not prevent the front seat from locking correctly. Refer to the information on the “Front seat” in Section 1.
child safety: fitting a child seat (2/6) The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
child safety: fitting a child seat (3/6) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. UD = Seat which only allows a rear-facing standardised “Universal” seat to be installed using a seat belt.
child safety: fitting a child seat (4/6) Visual installation of five door and estate versions Child seat fitted using the ISOFIX mounting ü ± Seat which allows a ISOFIX child seat to be attached. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached. The anchorage points are located in the boot for the rear seats, and on the seat back for the front seat.
child safety: fitting a child seat (5/6) View of the utility version installation Child seat fitted using the ISOFIX mounting ü ± seat which allows an ISOFIX child seat to be fitted. The passenger seat is fitted with an anchorage point for attaching a universal ISOFIX forward-facing child seat. The anchorage point is on the seatback.
child safety: fitting a child seat (6/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: deactivating/activating the front passenger air bag (1/3) DANGER 1 2 Deactivating the front passenger airbags (on equipped vehicles) You must deactivate the devices in addition to the front passenger seat belt before fitting a child seat in the front passenger seat. Since front passenger airbag triggering and the position of a rear-facing child seat are incompatible, NEVER use a restraining device for rearfacing children on a seat with an ACTIVATED AIRBAG in front of it.
child safety: deactivating/activating the front passenger air bag (2/3) 3 A A The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since front passenger airbag triggering and the position of a rear-facing child seat are incompatible, NEVER use a restraining device for rearfacing children on a seat with an ACTIVATED AIRBAG in front of it. This provides a risk of DEATH or SERIOUS INJURY to the CHILD. 1.
child safety: deactivating/activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbags activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. 1 Contact your approved dealer as soon as possible.
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 27 26 25 24 23 22 21 20 1.
DRIVING POSITION: LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 10 Door electric locking switch. 2 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights. 11 Multimedia touch-screen. 3 Instrument panel. 4 Driver Airbag and horn location. 5 Multimedia system voice control button. 12 Heating or air conditioning controls. 13 Passenger Airbag location. 22 Cigarette socket.
DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 26 27 22 21 20 19 1.
DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 11 Driver Airbag and horn location. 2 Passenger Airbag location. 12 Multimedia system voice control button. 3 Heating or air conditioning controls. 5 Windscreen demister outlet. 13 Stalk: – windscreen and rear screen wash/wipe; – trip computer and warning system information readout. 6 Hazard warning lights switch. 14 Side air vent. 7 Door electric locking switch.
warning lights (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. A 1 Instrument panel A: lights up when the ignition is switched on. The brightness can be adjusted by turning control knob 1. In some cases, the appearance of a warning light is accompanied by a message. The © warning light means you should drive very carefully to an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. 1.
warning lights (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. D A This comes on when the ignition is switched on and goes out as soon as the handbrake is released. If it comes on during braking and is accompanied by the ® warning light and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an approved Dealer.
warning lights (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ä A Electronic Stability Program (ESP) and traction control system (ASR) warning light This lights up when the ignition is switched on and goes out after a few seconds. There are several reasons for the warning light to come on: please refer to the information on “Dynamic driving control: ESP” and “Traction control: ASR” in Section 2. 1.
warning lights (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Φ A Speed limiter and cruise control indicator lights See the information on the “Speed limiter” and “Cruise control” in Section 2. Š‰ Fuel economy indicator light This lights up to advise you to change to a higher gear (up arrow) or lower gear (down arrow). Engine standby warning light Please see information about “Stop and Start function” in Section 2.
displays and indicators 2 3 4 1 5 Rev counter 1 Speedometer 3 Coolant temperature indicator 2 Overspeed buzzer (graduations x 1000) (km or miles per hour) Ô This is not serious unless the and ® warning lights come on, accompanied by a message on the instrument panel and a beep. 1.52 Depending on the vehicle, a buzzer sounds for approximately 10 seconds every 40 seconds, as long as the vehicle is travelling in excess of 72 mph (120 km/h).
ON-BOARD COMPUTER: general information (1/2) 1 2 f) distance travelled; g) average speed; h) distance before service; – service counter; – oil change counter; i) cruise control/speed limiter programmed speed; j) clock and temperature; k) trip log, operating faults and information message readout.
ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting 2 3 Resetting the trip mileage With “trip mileage recorder” selected on the display, press button 2 or 3 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) With one of the trip parameters selected as the display, press and hold button 2 or 3 until the display resets. 1.
ON-BOARD COMPUTER: trip settings (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km Fuel used 8L Average 7.2 L/100 a) Total mileage and trip mileage recorder. b) Journey parameters. Fuel used. Fuel consumed since the last reset. c) Average fuel consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset. Current 9.
ON-BOARD COMPUTER: trip settings (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range 541 km e) Estimated range with remaining fuel. The value is displayed after driving 400 metres. Distance 522 km f) Distance travelled since last reset. Average 123.4 km/H 1.56 g) Average speed since the last reset. The value is displayed after driving 400 metres.
ON-BOARD COMPUTER: trip settings (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections On-board computer without mileagebefore-service message OIL CHANGE IN 30000km/24 MOIS SCHEDULE SERVICE WITHIN 100km Service required Interpreting the display selected h) Mileage before service.
ON-BOARD COMPUTER: trip settings (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections On-board computer with mileagebefore-service message SERVICE INTERVALS Interpreting the display selected SERVICE IN 30,000 kms / 12 months SERVICE DUE 300 kms / 24 days Service required h) Mileage before service or oil change.
ON-BOARD COMPUTER: trip settings (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections On-board computer with distance before next service message (cntd.
ON-BOARD COMPUTER: trip settings (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Speed limiter 90 km/H i) Cruise control/speed limiter programmed speed. Cruise control Refer to the information on the “Speed limiter” and “Cruise control” in Section 2. 90 km/H 13° 16:30 j) Clock and temperature. Please refer to the information under “Clock and exterior temperature”. k) Trip log.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages “Parking brake on” Interpreting the display selected Indicates that the parking brake has been applied. “Please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Steering wheel/Power-assisted steering Power Assisted Steering Never drive with an inadequately charged battery. Variable power assisted steering 1 Adjusting the steering wheel height and depth The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed.
CLOCK AND EXTERIOR TEMPERATURE (1/2) A 2 9°C 12:00 1 3 Display A To access display 1 for setting the time, press button 2 or 3. Wait for a few seconds. The hours and minutes flash and you are now in setting mode; press and hold button 3 to set the hours. When the hours flash, repeatedly press or press and hold button 2, to set them. Then press and hold button 3 to confirm the time set. The minutes flash; repeatedly press or press and hold button 2 to set them.
CLOCK AND EXTERIOR TEMPERATURE (2/2) External temperature indicator Special note: B Display B Vehicles fitted with touch-screen multimedia, navigation aid systems, telephones, etc. Refer to the separate instructions for the function to understand the special features of this equipment. When the exterior temperature is - 3°C to + 3°C, the °C characters flash (signalling a risk of ice on the road).
REAR VIEW MIRRORS Heated door mirrors With the engine running, mirror deicing is activated simultaneously with rear screen de-icing/demisting. B A Folding door mirrors C D E 1 F (depending on vehicle) Move button 1 to position F: the door mirrors fold away. To reset them for driving, return to position C, D or E. If you manually fold the door mirrors, before setting them to the driving position (C, D, E), you must position control 1 to F.
EXTERIOR LIGHTING AND SIGNALS (1/3) k 1 2 3 1 Dipped beam headlights Manual operation Turn the ring 2 until the symbol is opposite mark 3. This indicator light on the instrument panel comes on. Automatic operation (depending on vehicle) Turn ring 2 until the AUTO symbol is opposite mark 3: with the engine running, the dipped beam headlights switch on or off automatically depending on the brightness of the light outside, without any action on stalk 1.
EXTERIOR LIGHTING AND SIGNALS (2/3) Switching off the lights 1 2 There are two possibilities: – Manually, move ring 2 to position 0; – automatically, the lights will go out when the engine is switched off, the driver’s door is opened or the vehicle is locked. In this case, the next time the engine is started the lights will be switched back on according to the position of the ring 2. NB: if the fog lights are lit, the lights are not switched off automatically.
EXTERIOR LIGHTING AND SIGNALS (3/3) f 4 1 Rear fog light Turn centre ring 4 on the stalk until the symbol faces mark 5, then release it. Operation of the fog lights depends on the exterior lighting selected, and an indicator light will light up on the instrument panel. 5 g To avoid inconveniencing other road users, remember to switch off the rear fog light when it is no longer needed. Front fog lights Turn centre ring 4 on the stalk 1 until the symbol faces mark 5, then release it.
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 1 2 One-touch mode A Horn Press steering wheel boss A. Headlight flasher Pull stalk 1 towards you to flash the headlights. When driving, it is possible that the steering wheel may not be turned sufficiently to return the stalk automatically to its starting position.
HEADLIGHT BEAM ADJUSTMENT For manual settings Examples of positions for adjusting control A according to the load A On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
WINDSCREEN WASH/WIPE (1/2) 1 1 E 2 A B C D F Vehicles with automatic wiper function With the engine running, move stalk 1 – A park. – B automatic wiper function When this position is selected, the system detects water on the windscreen and triggers the wipers at a suitable wiping speed. It is possible to change the triggering threshold and the time sweeps by turning ring 2: – E: minimum sensitivity With the ignition on, move stalk 1 Special note – A park.
WINDSCREEN WASH/WIPE (2/2) 1 1 A B C D Windscreen washer With the ignition on, pull stalk 1 towards you. A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer. A longer pull will trigger three sweeps of the wipers followed, a few seconds later, by a fourth, in addition to the windscreen washer. Before any action involving the windscreen (washing the vehicle, de-icing, cleaning the windscreen, etc.) return stalk 1 to position A (park). Risk of injury and/or damage.
REAR SCREEN WASH/WIPE p 2 1 Rear screen wash/wipe With the ignition on, turn the end of stalk 1 to align mark 2 with the symbol. When the stalk is released, it returns to the rear wipe position. Special note If the windscreen wipers are operating or are in automatic mode, the rear screen wiper wipes intermittently when reverse gear is engaged. Y wiper Speed-dependent timed rear screen With the ignition on, turn the end of stalk 1 to align mark 2 with the symbol. Wiping frequency varies with speed.
FUEL TANK (1/3) Fuel grade 1 2 Use a high-grade fuel that complies with the legislation in force in each country and which must comply with the specifications given on the label on the cover A. Please refer to the information on “Engine specifications” in Section 6. A B Petrol version It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover A. Refer to Section 6 for information on “Engine specifications”.
FUEL TANK (2/3) Filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). 3 Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion. Make sure that no water enters the fuel tank during filling.
fuel tank (3/3) 3 5 4 Running out of fuel on diesel versions Vehicles with priming bulb 4 After a breakdown caused by completely running out of fuel, the system must be reprimed before the engine is restarted: Fill the tank with at least 8 litres of diesel fuel. Press priming bulb 4 several times. The engine can now be restarted. If the engine does not start after several attempts, contact an approved Dealer. Vehicles without priming bulb 4 Insert the RENAULT card into the 5 card reader.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting, stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop and Start Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. For the first 900 miles (1,500 km), do not exceed 2,500 rpm. After completing this mileage you may drive faster, although you may only expect top performance after approximately 3,600 miles (6,000 km). You may only expect top performance from your vehicle after approximately 1,800 miles (3,000 km).
Starting/stopping the engine (1/3) Starting vehicles with an automatic gearbox 1 The lever should be in position P. 2 For all vehicles: 3 Remote control RENAULT card When you get into the vehicle, insert the RENAULT card integrated key, pointing towards you, fully into the card reader 2. To start, press button 1. If a gear is engaged, depress the clutch pedal to start the vehicle. Hands-free RENAULT card The RENAULT card must be inserted in card reader 2 or in detection zone 3.
Starting/stopping the engine (2/3) For other functions: 1 2 – vehicles with remote control RENAULT card, insert the card into reader 2; – vehicles with a RENAULT “handsfree” card, with the card in the passenger compartment or inserted in the card reader 2, press button 1 without depressing the pedals. Note: depending on the vehicle, pressing button 1 starts the engine. In certain cases, the hands-free RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc.
Starting/stopping the engine (3/3) Special note 1 2 If the card is no longer in the reader when you try to switch the engine off, the message “No keycard Press and hold” appears on the instrument panel: press button 1 for longer than two seconds. When you leave your vehicle, especially if you have your RENAULT card with you, check that the engine is completely switched off. Hands-free RENAULT card With the card in the vehicle, press button 1: the engine will stop.
Stop and start function (1/3) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc). Warning light is displayed on the instrument panel. This notifies you that the engine is on standby. The vehicle equipment remain operational while the engine is stopped.
Stop and start function (2/3) Conditions preventing the standby of the engine Depending on the vehicle, certain conditions prevent the system from using the engine standby function, including when: – reverse gear is engaged; – the bonnet is not locked; – the driver’s door is not closed; – the driver’s seatbelt is not fastened; – the outdoor temperature is too low or too high (less than around 0 °C or higher than around 30 °C); – the “Clear View” function is activated (please see the information on “Air con
Stop and start function (3/3) The system is automatically reactivated each time the vehicle is started using the start button (please see “Starting, stopping the engine)”. 1 Special note: engine on standby, press switch 1 to automatically restart the engine. Operating faults When the message “Check Stop & Start” appears on the instrument panel and the integrated warning light 2 lights up on the switch 1, the system is deactivated. Please consult an authorised dealer.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
Special features of diesel versions Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check anti-pollution system” is displayed on the instrument Ä and panel accompanied by the © warning light; consult an approved dealer straight away.
GEAR LEVER/Handbrake Handbrake To release: 1 2 3 Pull the lever 3 up slightly, press button 2 and then lower the lever to the floor. The red warning light on the instrument panel will light up if you are driving with an incorrectly released handbrake. To apply: Pull lever 3 upwards. Check that the vehicle is immobilised. The warning D Gear lever light come on.
eco-driving (1/2) Depending on the vehicle, you will have various functions which enable you to lower your fuel consumption: the rev counter; the gear change indicator; the driving style indicator; the journey record and eco-driving advice via the multimedia display; – ECO mode – activated by the ECO button. – – – – If fitted on the vehicle, the navigation system provides additional information.
eco-driving (2/2) 4 5 ECO mode Activating the function ECO mode is a function which optimises fuel consumption. It acts on all elements which consume fuel (engine power, heating and/or air conditioning, etc). The 5 ECO warning light comes on the instrument panel to confirm activation. Press switch 4. It is possible to regain your motor performance and exit this function at any time. To do this, depress the accelerator pedal firmly and fully. Disabling the function Press switch 4.
Advice: antipollution, fuel economy and driving (1/3) Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life which will come into force in 2015. Some parts of your vehicle have therefore been designed to facilitate future recycling. These parts are easy to remove so that they can be recovered and reprocessed by recycling companies.
Advice: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal. – Double declutching and accelerating before switching off are unnecessary in modern vehicles.
Advice: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and therefore helping to preserve the environment: Advice on use – Electricity is fuel; switch off all the electrical components which are not really needed.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the of the manufacturer eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
driver correction devices and aids (1/4) Depending on the vehicle, this is composed of: – anti-lock braking system (ABS); – electronic stability control (ESC) with understeer control and traction control (ASR); – emergency brake assist; – hill start assistance. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
driver correction devices and aids (2/4) Electronic stability program (ESC) with understeer control and traction control (ASR) Electronic stability control ESC This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
driver correction devices and aids (3/4) Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping distances. Operating principle The system is for detecting an emergency braking situation. In this case, the braking assistance immediately develops maximum power and may trigger ABS regulation. ABS braking is maintained as long as the brake pedal is applied. Hazard warning lights switching on Depending on the vehicle, these may light up in the event of sudden deceleration.
driver correction devices and aids (4/4) Hill start assistance This function assists the driver when starting on hills. It prevents the vehicle from rolling backwards, depending on the slope, by automatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) 6 2 3 4 5 1 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. Controls 1 Main “On/Off” switch. 2 Limit speed activation, storage and increase switch (+). 3 Decreasing the limit speed (-). 4 Activation and recall of memorised limit speed (R). 5 Speed limiter function standby (with limited speed memory) (O). 2.22 Switching on Press switch 1 on side .
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by repeatedly pressing: It is possible to exceed the limit speed at any time. To do this: press the accelerator pedal firmly and fully (beyond the resistance point). – switch 2 (+) to increase speed; 2 3 – switch 3 (-) to reduce speed. While the speed is being exceeded, the programmed speed displayed on the instrument panel flashes.
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been saved, it can be recalled by pressing switch 4 ((R)). 2 3 4 5 1 Putting the function on standby Switching off the function The speed limiter function is deactivated if you press switch 1: in this case a speed is no longer stored. The orange instrument panel warning light goes out, confirming that the function is stopped. The speed limiter function is suspended when you press switch 5 (O).
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) 2 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). 3 4 5 This function is an additional driving aid. However, the function does not take the place of the driver.
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) 7 6 2 3 1 Switching on Press switch 1 side . Indicator light 6 comes on, lit green, and the message “Cruise control” appears on the instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed. Activating cruise control Driving At a steady speed (above 18 mph (30 km/h approximately)) press switch 2 or (+): the function is activated and the current speed is saved.
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed 2 3 The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed 2 3 4 5 Putting the function on standby If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). Press switch 4 (R) if the vehicle speed is above 20 mph (30 km/h). When the stored speed is recalled, activation of the cruise control is confirmed by the illumination of the warning light.
AUTOMATIC TRANSMISSION (1/3) 1 2 5 3 5 4 Selector lever 1 Operation Gear change paddles 5 P: park With the selection lever 1 in position P, switch on the ignition. The paddles 5 enable you to change gear while the gear lever is in ‘manual mode’ position or, if driving, in ‘automatic mode’ position. R: reverse N: Neutral D: automatic mode M: manual mode +: upper gear –: lower gear 4: displays the gear engaged in manual mode.
AUTOMATIC TRANSMISSION (2/3) Driving in automatic mode Put lever 1 into position D. In most road conditions you will encounter, you will not need to touch your lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particular driving style you have chosen.
AUTOMATIC TRANSMISSION (3/3) Parking the vehicle When the vehicle is stopped, move the lever to position P while keeping your foot on the brake pedal: the gearbox is in neutral and the drive wheels are mechanically locked by the driveshaft. Apply the handbrake. Operating faults – when driving, if the ‘check gearbox’ message appears on the instrument panel, it indicates a fault.
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic detectors, installed in the rear bumper (depending on the vehicle), measure the distance between the vehicle and an obstacle whilst reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centimetres from the obstacle. NB: make sure that the ultrasonic sensors are not obscured (by dirt, mud, snow, etc.).
PARKING DISTANCE CONTROL (2/2) Operating faults 1 2 Adjusting the parking distance control volume Deactivating the system Depending on the vehicle, certain settings can be adjusted from the touchscreen 1. Please see the equipment instructions for further information. The indicator light built into the switch lights up to remind you that the system is deactivated.
Reversing camera (1/2) 2 1 1 Operation Moving into reverse gear, the 1 camera (located on the tailgate on five-seater versions or near the number plate lights on estate versions) provides a view of the area behind the vehicle on the 2 touchscreen. Depending on the vehicle, this may be accompanied by a moving guide line or a static guide line. 2.34 Note: make sure that the reversing camera is not obscured (by dirt, mud, snow, etc.).
Reversing camera (2/2) 3 4 C B This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. This system is initially used with the aid of several gauges (mobile for trajectory and fixed for distance). When the red zone is reached, use the bumper image to stop accurately. A Dynamic gauge 3 (depending on the vehicle) This is shown in blue on screen 2. It indicates the vehicle trajectory according to the position of the steering wheel.
2.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning/heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use . . . . . . . .
air vents, air outlets (1/2) 1 2 3 7 1 left-hand side window demister vent. 2 left-hand side air vent. 3 windscreen demisting vents. 4 centre air vents. 3.2 4 5 8 6 7 5 right-hand side air vent. 6 right-hand side window demister outlet. 7 passenger footwell heater outlets. 8 control panel.
air vents, air outlets (2/2) 11 9 12 To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. 10 Centre air vents. Side air vents Air flow Air flow Move the control knob 9 (beyond the resistance point). Upwards: opened to maximum. To open air vent 11, press on the air vent (point 12) until it is open as far as required. Down: closed. Direction Direction To direct the air flow, swivel side air vent 11.
Manual air conditioning (1/3) 1 2 3 4 7 6 The controls 1 Adjusting the air temperature. 2 Adjusting the ventilation speed. 3 Air conditioning. 4 Distribution of air in the passenger compartment. 5 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors. 6 Air recirculation. 5 Switching air conditioning on or off (depending on vehicle) The air conditioning is switched on (indicator light on) or off (indicator light off) using button 3.
Manual air conditioning (2/3) Distribution of air in the passenger compartment 1 2 3 4 There are five air distribution options. Turn control 4 to choose the distribution option. W i The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. ó G The air flow is directed mainly towards the footwells.
Manual air conditioning (3/3) 1 2 4 3 4 Adjusting the air temperature Turn control 1 to obtain the desired temperature. The further towards the red the slide is, the higher the temperature will be. When the air conditioning system is used for long periods, it may begin to feel cold. To increase the temperature, turn control 1 to the right. Rear screen de-icing/ demisting 5 5 6 Adjusting the ventilation speed Move control 2.
AUTOMATIC CLIMATE CONTROL (1/4) 1 2 3 Varying the ventilation speed 4 5 In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by turning control 6 to increase or reduce the ventilation speed. Adjusting the air temperature Turn control 2 to obtain the desired temperature. The controls 1 Automatic mode. 2 Air temperature adjuster. 3 “Clear View” function.
AUTOMATIC CLIMATE CONTROL (2/4) Clear View function Press button 3 – the integrated indicator light comes on. 1 3 4 This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-icing functions must be activated. Press button 8 to stop the heated rear screen operating, and the integrated indicator goes out. To exit this function, press button 3 or 1.
AUTOMATIC CLIMATE CONTROL (3/4) 5 9 Rear screen de-icing/ demisting 8 Press button 8 – the integrated indicator light comes on. This function enables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). To exit this function, press button 8 again. Demisting automatically stops. Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions.
AUTOMATIC CLIMATE CONTROL (4/4) Manual use 1 Press button 7 – the integrated indicator light comes on. Prolonged use of this position may lead to odours, caused by non-renewal of air, and the formation of condensation on the windows. We therefore advise you to return to automatic mode as soon as air recirculation is no longer needed, by pressing button 7.
AIR CONDITIONING: information and advice on use Advice on use Fuel consumption Operating faults In some situations, (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.) you may notice that condensation starts to form on the windows and windscreen. You will normally notice an increase in fuel consumption (especially in town) when the air conditioning is operating. As a general rule, contact your approved dealer in the event of an operating fault.
electric windows (1/2) These systems operate with the ignition on or off, until one of the front doors is opened (limited to about 3 minutes). Safety of rear occupants The driver can prevent operation of the rear electric windows by pressing switch 4. A confirmation message is displayed on the instrument panel. Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a child (or a pet) unsupervised, even for a short while.
electric windows (2/2) One-touch mode Operating faults Depending on the vehicle, this mode works in addition to the operation of the electric windows described previously. It is only fitted to the driver’s window. Briefly press or pull switch 1 fully: the window is fully lowered or raised. Pressing the switch again stops the window moving.
fixed sunroof/sun visor 2 1 3 Fixed sunroof blind Front sun visor – Opening: push handle 1 upwards, then guide it until it opens fully; Lower sun visor 2. – Closing: pull the handle 1 until it clicks into the catch. Courtesy mirrors If the blind becomes skewed when opening or closing, close fully and then fully open the blind. 3.14 Slide cover 3.
INTERIOR LIGHTING 1 2 3 4 Courtesy light Luggage compartment light 4 Press switch 2 for: Light 4 comes on when the boot is opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened. It only switches off after a time delay and when the doors concerned have been closed correctly; – lighting switches off immediately. Map reading lights Press switch 1 for the driver, 3 for the front passenger.
PASSENGER COMPARTMENT STORAGE, FITTINGS (1/4) 2 3 1 Front door storage pockets 1 Sun visor storage 2 They can hold a 1.5 litre bottle. This can be used for storing motorway tickets, cards, etc. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 3.
PASSENGER COMPARTMENT STORAGE, FITTINGS (2/4) 4 6 7 8 5 Passenger storage compartment 4 Passenger storage compartment 5 Armrest storage compartment With the armrest in its lowered position, press button 6 and lift armrest cover. Storage compartment 7 Cup holders 8 This can be used for storing a mobile ashtray, cup holder, etc. Pull handle 5 to open it. 3.
PASSENGER COMPARTMENT STORAGE, FITTINGS (3/4) 10 9 Rear centre console storage compartment 9 This can be used for storing a mobile ashtray, cup holder, etc. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of injury if hot liquid escapes. 3.
PASSENGER COMPARTMENT STORAGE, FITTINGS (4/4) 12 11 Rear door storage compartment 11 Grab handle 12 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning, braking or in the event of an accident. 3.
Ashtray, cigarette lighter, accessories socket Accessories socket 1 1 It is provided for connecting accessories approved by our Technical Department with a maximum power of 120 Watts (12V). 3 2 Cigarette lighter 1 Ashtray With the ignition on, push in the cigarette lighter 1. It will spring back with a click when it is ready. Pull it out to use. It can be housed in either position 2 or 3. After use, replace it without pushing it all the way in.
REAR HEAD RESTS A Position for use To raise the headrest Raise the headrest as far as possible to use it in the high position. Check that it is correctly locked. Raise the headrest as far as it will go, then press button A and remove the headrest. Storage position To refit the headrest Press button A and lower the headrest completely. Enter the rods in their housing and push down the headrest until it locks to use it in the high position. Check that it is correctly locked.
REAR BENCH SEAT: functions To replace the seatback, proceed in the reverse order to removal. Refit the seatback and click it back into place. B A 1 When moving the rear seats, ensure that nothing obstructs the anchorage points (passenger’s arm or leg, a pet, gravel, cloth, toys, etc.). To fold down the seatback Ensure that the front seats are far enough forward. Lower the headrests fully. Place the seat belts in their guides A. Press button 1 and lower the seatback B.
Boot 2 1 To open Press button 1 and lift the tailgate. To close Lower the tailgate using the handles 2 inside the tailgate to help you. 3 Opening the doors manually from the inside If it is impossible to unlock the tailgate, it can be done manually from inside: – access the luggage compartment by tilting the rear bench seatback(s), – insert a pencil or similar object in recess 3 and slide the unit as shown in the illustration; – push the tailgate to open it.
Rear parcel shelf 2 1 A A Removal – push the shelf in and turn; – Lower the rear headrests; – pull the shelf towards you. – lift the shelf A upwards; To refit, proceed in the reverse order to removal. – unhook the two cords 1 (boot side); Maximum weight on rear parcel shelf: 25 kg, evenly distributed. 3.24 Utility version Unclip mountings 2 on either side of the parcel shelf, then remove it via the boot. To refit it, proceed in the reverse order to removal.
LUGGAGE COMPARTMENT COVER: estate version A 1 B 2 To remove the flexible section of the luggage compartment cover 1 Pull handle 2 gently to release the pins from their mounting points located on each side of the luggage boot. Guide the luggage cover onto the roller. 1 1 Removing the luggage compartment cover Luggage compartment cover storage 1 Using the handle 2, push the luggage cover to the right (movement A) and lift the left-hand side (movement B) in the inertia reel.
BOOT ARRANGEMENTS 5 3 4 2 1 Mobile floor When fitted to the vehicle, it can be used to make loading easier. Note: if you need to access the ISOFIX ring and/or the net ring at the bottom of the boot, open flap 3. Maximum weight for the mobile floor: 100 kg evenly distributed. 3.26 Movable floor storage Removing the mobile floor – Lower section 1 onto section 2; – Lower section 1 onto section 2; – lift the assembly and position it against the back of the rear bench seat; – remove the assembly.
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). A 1 – The front seatbacks with the rear seatbacks folded down, as is the case for maximum loads (example B). If you have to place objects on the folded seatback, it is necessary that you lower the headrests before folding the seatback so that it can be folded as flat as possible against the seat.
TRANSPORTING OBJECTS towbar A A: 697 mm (5-door version). A: 697 mm (Utility version). A: 948 mm (Estate version). Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. For fitting and conditions of use, refer to the equipment’s fitting instructions. Please keep these instructions with the rest of the vehicle documentation. 3.
Transporting objects: Luggage net (1/2) 1 2 A Luggage net A On equipped vehicles, this can be used when transporting animals or luggage, to separate them from the passenger section.
Transporting objects: Luggage net (2/2) 3 4 C 5 Fitting the luggage net behind the rear bench seat Inside the vehicle on each side: – lift the cover 3 to access the upper mounting ring for the net; – fix the net strap hook onto the ring; 6 B – in the boot, it is essential to attach the hook of the lower mounting strap of the net to the anchoring hook 5 identified by the marking 7 (if fitted to a mobile floor B, open flap 4 to access the anchoring hook 5); – adjust the net strap C so that it is taut.
ROOF BARS/SPOILER Precautions during use 1 Handling the tailgate 2 1 2 Accessing the mounting points Open the doors. Behind seal 2 are blanking bolts 1 which protect the mounting bolt locations. When fitting roof bars, replace the blanking bolts with the mounting bolts supplied with the roof bars. Spoiler For information on the range of equipment adapted to your vehicle, we advise you to consult an approved Dealer.
multimedia equipment The presence and location of this equipment depends on the vehicle version. 1 2 3 4 5 Multimedia touch-screen; Multimedia sockets; Steering column control; Voice commands; Microphone. 1 4 5 2 3 To use this equipment, consult the instructions for the equipment which should be kept with the other vehicle documentation. Using the telephone We remind you of the need to conform to the legislation in force concerning the use of such equipment. 3.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: topping up, filling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil change . . . . . . . . . . . . . . . . . . . . . .
BONNET Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight. 2 1 To open the bonnet, pull the handle 1. When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position. Risk of injury. The engine may be hot when carrying out operations in close proximity.
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. A B In order to prevent splashback, it is recommended that a funnel be used when topping up/filling with oil However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.
ENGINE OIL LEVEL: topping up/filling (1/2) 1 2 1 1 2 2 Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). – Unscrew cap 1; – top up the level (as a guide, the capacity between the minimum and maximum reading on the dipstick 2 is between 1.
ENGINE OIL LEVEL: topping up, filling (2/2)Oil change Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. 2 1 Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change including oil filter (for information) Engine 0.9 TCe: 4.1 litres Engine 1.2 16V: 4.0 litres Engine 1.2 TCe: 4.6 litres Engine 1.5 dCi: 4.5 litres Deactivate the Stop and Start function for any operation performed in the engine compartment.
LEVELS (1/3) 1 Frequency of checking coolant level Replacement interval Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Document for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – an anti-corrosion protection for the cooling system.
LEVELS (2/3) Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warning line. 2 If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from the manufacturer’s network or web site. Topping up Brake fluid level The level should be read with the engine switched off and on level ground.
LEVELS (3/3)/FILTERS Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. 3 Replacement intervals for filter elements: refer to the Maintenance Document for your vehicle. Windscreen washer reservoir Topping up With the engine switched off, open the cap 3. Fill until you can see the fluid, then replace the cap. Liquid Screen wash product (product with antifreeze in winter).
Tyre pressure E: front tyre pressure. A F: rear tyre pressure. A G: tyre pressure for the emergency spare wheel. B C C D E E E F F F G Label A Open the driver’s door to read it. Tyre pressures should be checked when the tyres are cold. If the tyre pressures cannot be checked when the tyres are cold, increase the pressures from 0.2 to 0.3 bar (or 3 PSI). Never deflate a hot tyre. B: dimension of the tyres fitted to the vehicle. C: intended driving speed.
BATTERY Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. A 2 3 4 7 2 6 5 1 Label A Observe the indications on the battery: – 2 naked flames and smoking are forbidden; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; – 6 refer to the handbook; – 7 corrosive materials. This is located under cover 1 and does not need to be serviced.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences. Corrosive agents in the atmosphere – atmospheric pollution (built-up and industrial areas), – saline atmospheres (near the sea, particularly in hot weather), – seasonal and damp weather conditions (e.g.
Bodywork maintenance (2/2) Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway). Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Document.
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture, emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel trims - wheel. . . . . . . . . . . . . . .
PUNCTURE, EMERGENCY SPARE WHEEL (1/4) In case of puncture Depending on the vehicle, a tyre inflation kit or emergency spare wheel is provided (refer to the following pages). If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use. Vehicle fitted with an emergency spare wheel that differs from the other wheels: – Never fit more than one emergency spare wheel to the same vehicle.
PUNCTURE, EMERGENCY SPARE WHEEL (2/4) 1 3 4 A 5 6 2 Emergency spare wheel – – – – Open the tailgate; lift the carpet; lift the cover 1 and remove it; remove the tool kit by lifting it by its handles; – unscrew nut 3 in an anti-clockwise direction until it comes off completely, then place the palm of your hand on section A of handle 4 and push towards the front of the vehicle. The wheel will be lowered; – pull the wheel towards you; – lay the wheel down flat and unfasten cable 5 from its housing 6.
PUNCTURE, EMERGENCY SPARE WHEEL (3/4) 4 5 6 7 8 To refit a wheel Do not refit a wheel with an alloy wheel rim or a wheel larger than 16” under the vehicle. To carry out this operation, the cable must be unwound. If the cable has been wound back up on its own, unwind it again as follows: – pull the handle to unwind the cable; – press the button located under handle 4 to hold the unwound cable, then guide it down; – recover the cable from underneath the vehicle.
PUNCTURE, EMERGENCY SPARE WHEEL (4/4) NB: if the tool kit does not lock in place, check the tightness of nut 3 and the correct positioning of handle 4. Special features 3 4 The emergency spare wheel holder should always be present when you are driving even when the wheel itself is not present: risk of water entering the vehicle. If you have to release it when it is not holding a wheel, push the centre of the wheel holder towards the ground while pressing handle 4.
TYRE PRESSURE KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) With the engine running and the parking brake applied, – unroll the hose from the container; 1 8 2 7 6 5 4 3 Depending on the vehicle, in the event of a puncture, use the kit located in the boot or underneath the luggage compartment carpet. Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic.
TYRE PRESSURE KIT (3/3) 1 – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; – Put the kit away. – At the end of this initial inflation operation, air will still escape from the tyre. You must drive a short distance in order to seal the hole. – Start immediately and drive at between 12 and 40 mph (20 and 60 km/h) in order to distribute the product evenly in the tyre and, after driving for 2 miles (3 km), stop and check the pressure.
TOOLS Jack 2 2 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned). 1 Hubcap tool 3 A 6 3 4 5 The tools included in the tool kit depend on the vehicle. Tool kit A is located in the tray under the luggage compartment carpet. Lift the cover and remove it. Wheelbrace 1 Locks or unlocks the wheel bolts and tow eye 5. This tool is used to remove the wheel trims. Wheel bolt guide 4 To finish loosening or starting to tighten the wheel bolts.
WHEEL TRIMS - WHEEL 1 A 2 C B D Remove the wheel trim using hubcap tool 1 (located in the tool kit) by engaging the hook in the opening near valve 2. To refit it, align it with valve 2. Push the retaining hooks in fully, starting with side A near the valve, followed by B and C, finishing at D opposite the valve. We would advise you to note down the number engraved on the tool so that you can replace it if it is lost. 5.
CHANGING A WHEEL (1/2) 1 Vehicles equipped with a jack and wheelbrace If necessary, remove the wheel trim. Use the wheelbrace 1 to slacken off the wheel bolts. Position it so as to be able to push from above. 3 2 Continue to crank the jack so that the baseplate is correctly positioned (it should be underneath the vehicle and aligned with the jack head). Turn it a few times to lift the wheel off the ground.
CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. Tighten the bolts, checking that the wheel is correctly positioned on its hub. Lower the jack. With the wheel on the ground, tighten the bolts fully and have the tightness of the bolts checked (tightening torque: 105 N.m) and the emergency spare tyre pressure checked as soon as possible.
TYRES (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. 2 You must make sure that your tyres conform to local road traffic regulations. 1 When the tyre tread has been worn to the level of the warning strips, they become visible 2: it is then necessary to replace your tyres because the tread rubber is now only 1.6 mm deep at most, resulting in poor road holding on wet roads.
TYRES (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, assume an increase of 0.2 to 0.3 bar (or 3 PSI).
TYRES (3/3) Use in winter Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. Snow or Winter tyres Studded tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion. This type of equipment may only be used for a limited period and as laid down by local legislation.
FRONT HEADLIGHTS: changing bulbs (1/3) Main beam headlight To change the bulb: 1 – remove cover C; – disconnect wiring 4; – unclip spring 5 and remove the bulb. 2 A C B Bulb type: H1 5 3 4 It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights. Do not touch the bulb glass. Hold it by its base. When the bulb has been changed, make sure you refit the cover correctly.
FRONT HEADLIGHTS: changing bulbs (2/3) 5 6 A A Front side light To change a bulb, remove cover A. Pull bulb holder 6 to access the bulb. Bulb type: W5W. The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling fan can come on at any moment. Risk of injury. To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an approved dealer.
FRONT HEADLIGHTS: changing bulbs (3/3) Additional lights If you wish to fit fog lights to your vehicle, please see an authorised dealer. 7 8 Daytime running lights 7 Please see an authorised dealer. Front fog lights 8 The front bumper needs to be removed; consult an approved Dealer. Bulb type: H16. 5.
REAR AND SIDE LIGHTS: changing bulbs (1/4) A 2 5 3 6 B 1 4 Five-door version Side lights/brake and direction indicator lights Open the boot lid and remove screws 1. To release the light unit, start by moving the exterior edge away to a sufficient extent (movement A) to release clip 3, then pull the light unit backwards (movement B). Remove the bulb holder by carefully releasing clips 4, lightly raise the bulb holder and then release clip 2. Change the bulb.
REAR AND SIDE LIGHTS: changing bulbs (2/4) 9 7 8 Estate version Side lights/brake and direction indicator lights Unclip the cover to access nut 7. Unscrew nut 7. Unscrew screw 8. Pull the light unit backwards (movement A). Remove the bulb holder by carefully releasing clips 9, and gently pull the bulb holder. Change the bulb. Refit the bulb holder and push the unit as far as it will go, until it locks into place. Check that the light is properly locked in position. Tighten the screw 8 and nut 7.
REAR AND SIDE LIGHTS: changing bulbs (3/4) 14 13 12 Five door and estate versions Reversing lights and rear fog lights 12 Open the boot lid. Unclip cover 13 and remove it. Turn bulb holder 14 fully anticlockwise and change the bulb. To reassemble, proceed in the reverse order to removal. When the bulb has been changed, make sure you refit the cover 13 correctly. Reversing lights Bulb type: H21. Rear fog lights Bulb type: H21. 5.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (4/4) 15 17 16 17 High-level brake light 15 Consult an approved dealer. Number plate lights 16 Side indicator lights 18 – Unclip light 16 by pressing tab 17; Consult an approved dealer. – remove the light cover to gain access to the bulb. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTING: changing bulbs 3 1 2 4 Courtesy light Luggage compartment light Unclip the lens (using a flat-blade screwdriver or similar). Unclip light 2 by pressing the tabs on each side (using a flat-blade screwdriver or similar). Remove the bulb concerned. Bulb type 1: W5W. Press tab 3 to release the bulb holder and access bulb 4. Bulb type: C5W festoon type bulb. Disconnect the light. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
RENAULT card: battery 2 A B 4 1 Replacing the battery When the message “Replace card battery” appears on the instrument panel, replace the RENAULT card battery, press button 1, pulling on emergency key 2, then unclip cover 3 using tab 4. Remove the battery by pressing on one side (movement A) and by lifting the other (movement B) then replace it, ensuring the polarity and model, shown on cover 3 are respected.
FUSES (1/5) 1 B A Fuses in passenger compartment A If any electrical component does not work, check the condition of the fuses. Unclip the access flap A. Allocation of fuses: If the vehicle is fitted with automatic windscreen wipers and automatic headlights, please see diagram C. Otherwise, please see diagram D. To comply with current legislation, or as a precaution, you can obtain an emergency kit from your approved dealer containing a set of spare bulbs and fuses.
FUSES (2/5) Allocation of fuses diagram C (the presence of certain fuse depends on the vehicle equipment level) 1 2 3 18 19 27 28 5.
FUSES (3/5) Number Allocation 1 Front windscreen wiper 2 Front left daytime running light, right side light, lefthand main beam headlight, right-hand dipped beam headlight 3 Interior lighting, registration plate lighting, fog light 4 Empty location 5 7 Empty location Front right daytime running light, left side light, righthand main beam headlight, left-hand dipped beam headlight Empty location 8 Empty location 9 Empty location 10 Steering column control 11 Door locking, rain and light s
FUSES (4/5) Allocation of fuses diagram D (the presence of certain fuse depends on the vehicle equipment level) 1 2 3 18 19 27 28 5.
FUSES (5/5) Number Allocation 1 Empty location 2 Front fog lights 3 Wipers 4 Right-hand side lights 5 Left-hand side lights 6 7 8 9 Right-hand dipped beam headlight Left-hand dipped beam headlight Right-hand main beam headlight Left-hand main beam headlight Number Allocation 13 ABS-ESC, brake switch 14 Steering column control 15 Horn 16 Rear fog lights 17 19 Cigarette lighter Radio and multimedia, diagnostic socket Power-assisted steering 20 Empty location 21 18 Automatic gear
BATTERY: breakdown recovery (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any electrical consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery. The battery charger must be compatible with a battery with nominal voltage of 12 volts. – When charging, stop the charger before connecting or disconnecting the battery. Do not disconnect the battery when the engine is running.
BATTERY: breakdown recovery (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts.
FITTING A RADIO 1 2 Radio location 1 Door speakers 2 Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. To install any equipment, please consult an authorised dealer. – In all cases, it is very important to follow the manufacturer’s instructions carefully. – The specifications of the brackets and wires (available from our network) vary depending on the equipment level of your vehicle and the type of radio.
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory, make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 watts only. Fire hazard. No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected system may result in damage being caused to the electrical equipment and/or the components connected to it.
WINDSCREEN WIPER BLADES (1/2) 1 Check the condition of the wiper blades. You are responsible for their service life: A B 3 4 2 Replacing windscreen wiper blades 1 – With the ignition off, lift wiper arm 2; – turn blade 1. A Lower tab 3, by pressing on either side A. Then push the blade forwards B, to release hook 4. To refit To refit the wiper blade, proceed in reverse order to removal. Make sure that the blade is correctly locked in position.
WINDSCREEN WIPER BLADES (2/2) To refit To refit the wiper blade, proceed in reverse order to removal. Make sure that the blade is correctly locked in position. 5 6 Rear screen wiper blade 5 – With the ignition off, lift wiper arm 6; – release the blade 5 by pulling it. – In frosty weather, make sure that the wiper blades are not stuck by ice (to avoid the risk of the motor overheating). – Check the condition of the wiper blades.
TOWING: breakdown recovery (1/2) Before towing, unlock the steering column: with the clutch depressed, engage first gear (lever in position N or R for vehicles with automatic gearboxes), insert the RENAULT card in the card reader, then press the engine start button for two seconds. Reposition the lever to neutral (position N for vehicles fitted with an automatic gearbox). The column is unlocked, the accessory functions are supplied: the vehicle lights can be used (indicators, brake lights etc.).
TOWING: breakdown recovery (2/2) 5 2 – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. 3 3 4 6 Only use the front 2 and rear 5 towing points (never use the drive shafts or any other part of the vehicle). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly.
Operating faults (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery. You can still lock/ unlock and start your vehicle (refer to the information on “Locking/unlocking the doors” in Section 1 and “Starting/Stopping the engine” in Section 2).
Operating faults (2/5) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are Battery terminals not tight, Retighten or reconnect the terminals, or clean them if weak or fail to light up and the starter battery terminals discon- they are oxidised. does not turn. nected or oxidised. Discharged battery or not operational. The engine will not start. The engine cannot be switched off. The steering column remains locked. Connect another battery to the faulty battery.
Operating faults (3/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved Dealer. White smoke from the exhaust. This is not necessarily a fault. Smoke may be caused by regeneration of the particle filter. Please refer to the information on “Special features of diesel versions” in Section 2. Smoke under the bonnet.
Operating faults (4/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The coolant temperature indicator is in the warning zone and warning light ® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
Operating faults (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb.
Section 6: Technical specifications Vehicle identification plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . .
Vehicle identification plates A A 10 9 1 2 3 4 5 6 7 8 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. The presence and location of the information depends on the vehicle. B 6.2 Vehicle identification plate A 1 Manufacturer name. 2 EC design number or approval number. 3 Identification number. Depending on the vehicle, this information is also given on marking B. 4 MAM (Maximum Authorised Mass) for front axle.
ENGINE IDENTIFICATION plates A 1 2 3 A A Please quote the information on the engine plate or label A in all correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. A 6.
dimensions (in metres) (1/2) Five-door version 0,853 2,589 0,621 1,509 4,063 1,448 1,512 1,945 * unladen 6.
dimensions (in metres) (2/2) Estate version 0,853 2,589 0,825 1,509 4,267 1,445 1,512 1,945 * unladen 6.
ENGINE SPECIFICATIONS Versions Engine type (see engine plate) Cubic capacity (cc) Type of fuel Octane rating 0.9 TCe 1.2 16V 1.2 TCe 1.5 dCi H4B Turbo D4F H5F Turbo K9K Turbo 898 1149 1 197 1461 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
Anticorrosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/5) A ABS...............................................................1.50, 2.18 → 2.21 accessories........................................................................ 5.33 accessories socket............................................................. 3.20 additional methods of restraint........................................... 1.29 side protection.............................................................. 1.28 to the front seat belts........................................
Alphabetical index (2/5) driving position settings.............................................................1.19 → 1.22 E electric beam height adjustment......................................... 1.72 electric windows...................................................... 3.12 – 3.13 electronic stability control: ESC..............................2.18 → 2.21 emergency brake assist.........................................2.18 → 2.21 emergency braking.................................................2.18 → 2.
Alphabetical index (3/5) indicators: direction indicators........................................................ 1.71 instrument panel...............................................1.48 → 1.54 instrument panel.....................................................1.48 → 1.63 instrument panel messages...................................1.53 → 1.63 interior trim maintenance...................................................... 4.13 – 4.14 Isofix...................................................................
Alphabetical index (4/5) rear bench seat.................................................................. 3.22 rear parcel shelf.................................................................. 3.24 rear seats........................................................................... 1.21 functions....................................................................... 3.22 rear view mirrors................................................................. 1.67 RENAULT ANTI-INTRUDER DEVICE (RAID)...........
Alphabetical index (5/5) tyre pressures....................................................................... 4.9 tyres.................................................................4.9, 5.13 → 5.15 U unlocking the doors................................................. 1.12 – 1.13 V variable power-assisted steering........................................ 1.64 vehicle identification plates................................................... 6.3 ventilation...................................................
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
