Specifications

88A-145
WIRING HARNESS
Rear wiring: Removal - Refitting
C85 or S85
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equip-
ment).
a Lock the airbag computer using the Diagnostic tool
(see MR 394, 88C, Airbags and pretensioners).
a Switch off the ignition.
a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-1) .
a Remove:
- the front seats (see Complete front seat: Remov-
al - Refitting) (MR 393, 75A, Front seat frames
and runners),
- the rear bench seat base (see Single unit rear
bench seat base: Removal - Refitting) or (see 1/
3 and 2/3 rear bench seat base: Removal - Refit-
ting) (depending on the equipment level) (MR 393,
76A, Rear seat frames and runners),
-the rear bench seatback (see Single unit rear
bench seatback: Removal - Refitting) or (see 1/3
and 2/3 rear bench seatback: Removal - Refit-
ting) (depending on the equipment level) (MR 393,
76A, Rear seat frames and runners),
- the rear right-hand and left-hand panel trim (see
Rear panel lining: Removal - Refitting) (MR 393,
71A, Body internal trim),
- the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 393, 71A, Body in-
ternal trim),
- the wheel arch trims (see Rear wheel arch trim:
Removal - Refitting) (MR 393, 71A, Body internal
trim),
- the front door sill inner trims (see Front door sill
lining: Removal - Refitting) (MR 393, 71A, Body
internal trim),
-the centre console (see Centre console: Removal
- Refitting) (MR 393, 57A, Interior equipment),
- the rear centre floor carpet (see Centre floor rear
carpet: Removal - Refitting) (MR 393, 71A, Body
internal trim),
- the front centre floor carpet (see Centre floor front
carpet: Removal - Refitting) (MR 393, 71A, Body
internal trim),
- the side soundproofing of centre floor (see Centre
floor side soundproofing: Removal - Refitting)
(MR 393, 68A, Soundproofing),
- the rear soundproofing of centre floor (see Centre
floor rear soundproofing: Removal - Refitting)
(MR 393, 68A, Soundproofing),
Equipment required
Diagnostic tool
Tightening torquesm
earth terminal nuts 8 Nm
IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-5) .
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the diag-
nostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the
instrument panel lights up continuously (ignition
on).
IMPORTANT
Never handle the pyrotechnic systems (pretension-
ers or airbags) near to a source of heat or naked
flame - they may be triggered.
WARNING
To prevent damage to the wiring harness when
refitting, observe the original routing.
WARNING
To prevent damaging the connectors, consult the
disconnection procedure (see Connector: Dis-
connection and reconnection) (Technical Note
6015A, 88A, Wiring).