Data Sheet

ManualsBrandsRENATA ManualsRechargeablesNon-standard battery (rechargeable) Prismatic Cable LiPo ICP606168PRT 3.7 V 2800 mAh

E n g i n e e r i n g s p e c i f i c a t i o n s u b j e c t t o c h a n g e s w i t h o u t n o t i c e .

Renata SA Switzerland

Engineering Specification

Model No. : ICP606168PRT

Issued Date : 2013/07/24

Version: V 0.0

Summary of content (13 pages)

PAGE 1
Renata SA Switzerland Engineering Specification Model No. : ICP606168PRT Issued Date : 2013/07/24 Version: V 0.0 Engineering specification subject to changes without notice.
PAGE 2
Model Description Rev. Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 2/13 1. Preface The purpose of this engineering specification is to provide technical information for the rechargeable Lithium-ion polymer battery pack ICP606168PRT. 2. Description and Model 2.1 Description Rechargeable Lithium-ion Polymer Battery Pack 2.2 Model ICP606168PRT 3. Specifications 3.1 Typical Capacity 3.3 Charging Voltage 2800mAh (at 0.2C rate discharge process after standard charge) 2700mAh (at 0.
PAGE 3
Description Rev. Page Lithium-ion Polymer Battery Pack Rev.0.0 3/13 Model ICP606168PRT 4.Outline Dimension See attached drawing for ICP606168PRT (Fig. 1). thickness as of shipment state. The thickness is the maximum 5. Appearance Free from deformation, damage, noticeable scratch, flaw, rust, discoloration or electrolyte leakage. 6. Standard Test Condition 6.
PAGE 4
Description Model ICP606168PRT Rev. Page Rev.0.0 4/13 Lithium-ion Polymer Battery Pack 8. Test Procedure and its Standard Item Measuring Procedure 8.1 Appearance Visual Standard No Defects and Leakage 8.2 Dimension Caliper for dimension As item 4 8.3 Weight Balance As item 3.12 8.4 Initial Open Circuit Voltage 8.5 Initial Internal Impedance 8.6 Discharge Capacity Voltmeter 3.7~3.9V Measure the AC impedance at 1kHz ≤ 200mΩ (50% SOC) 8.
PAGE 5
Model Description Rev. Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 5/13 8.8 Charge/Discharge Cycle Life Discharge capacity should be≧80% of 1st cycle capacity @ 500th cycle. 0.5C Rest for 10 minutes between each Discharge: 0.5C to 3.0V charge/discharge step. 8.9 Leakage Proof The fully charged battery shall be stored at No leakage. 65±3℃and relative humidity 95±5% for 7 days. Discharge capacities should 8.10 Temperature 1)Charge:CC/CV,CC-0.5C,CV-4.2V be ≧60% for -10±3℃ and Cut-off 0.
PAGE 6
Model Rev. Description Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 6/13 10. UL 1642 Safety Criteria for Acceptance Item State Test method Specification External Short-circuit Fully Charged Cell terminals are short-circuited for 6 hours NO EXPLOSION or longer with a resistance of 50mΩ or less. or FIRE. Test Tests are to be conducted at room temperature and 55℃. Forced-Discharge Fully Charged Cell is discharged at a current of 1C rate for NO EXPLOSION Test 2.5 hours.
PAGE 7
Model Rev. Description Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 7/13 11. Battery Pack Safety Criteria Item State Test method Specification Overcharge Test Fully Discharged Test passed according - Fully charge battery pack Settings: CVC mode: 4.2V, time: 300 to test method. min, set charging current (0.8C), cut-off by taper current (or end Current) 0.02C. - Continuously charge battery pack Settings: CVC mode: 4.6V, time: 60 min, set charging current (0.2C).
PAGE 8
Model Rev. Description Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 8/13 12. Charge State of Battery Before Shipment The battery is charged to approximately 50 % of minimum capacity. Voltage is 3.7V~3.9V. This measuring test should be performed within one month after shipment from our factory. 13. Handling Precautions ICP battery pack shall have enough protection for ICP cell from the specification of electrical, mechanical and environmental characteristics.
PAGE 9
Model Rev. Description Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 9/13 (6) Don’t drive a nail into a battery, strike it by hammer, or tread it. As the battery might be broken or deformed and then it will be short-circuited, it would cause the generating, smoke, rupture or flaming. (7) Don’t give battery impact or fling it If the protection circuit assembled in the battery is broken, the battery will be charged at abnormal voltage or current and abnormal chemical reaction will occur.
PAGE 10
Model Rev. Description Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 10/13 (2) Don’t get into a microwave or a high pressure container Because of sudden heat or damage of sealing condition of battery, it may cause the generating, smoke, rupture or flaming. (3) Don’t use a leaked battery nearby fire If the liquid leaks from the battery (or the battery gives out bad smell), let the battery leave from flammable objects immediately.
PAGE 11
Model ICP606168PRT 14. History of Revision Description Rev. Page Lithium-ion Polymer Battery Pack Rev.0.0 11/13 REV. ISSUE CONTENT OF AMENDMENT PRE. CHK. APP. 0.0 July 24, 2013 1st Edition MKL KW KW End Engineering specification subject to changes without notice.
PAGE 12
Model Description Rev. Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 12/13 Fig.1 Engineering specification subject to changes without notice.
PAGE 13
Model Description Rev. Page ICP606168PRT Lithium-ion Polymer Battery Pack Rev.0.0 13/13 Part list: Item Ref Part name Number Qty 1 R1 RES 470Ω/±5% 1 2 R2 RES 1KΩ/±5% 1 3 C1, C2, C3 CAP 0.1uF/±10% 3 4 U1 CONTROL IC S-8241AAXMC 1 SEIKO 5 U2 MOSFET STG8209/TSSOP8 1 SAMHOP 6 NTC NTC NTCG163JF103FT/0603 /10KΩ/±1%/B=3435 7 -- PCB B(S)W2804.