Approve datasheet Model:: Version: Description: ICP422339PR V2.0 3.
Renata SA Switzerland Product Specification Model No. : ICP422339PR Issued Date : 2016/03/10 Version: V 2.
Model Description Rev. Page ICP422339PR Lithium-ion Polymer Battery Pack Rev.2.0 2/13 1. Preface The purpose of this product specification is to provide technical information for the rechargeable Lithium-ion polymer battery pack ICP422339PR. 2. Description and Model 2.1 Description Rechargeable Lithium-ion Polymer Battery 2.2 Model Pack ICP422339PR 3. Specifications 3.1 Typical Capacity 340mAh (at 0.2C rate discharge process after standard charge) 3.2 Minimum Capacity 330mAh (at 0.
Description Rev. Page Lithium-ion Polymer Battery Pack Rev.2.0 3/13 Model ICP422339PR 4. Outline Dimension See attached drawing for ICP422339PR (Fig. 1). after 500 cycles. The thickness is the maximum thickness 5. Appearance Free from deformation, damage, noticeable scratch, flaw, rust, discoloration or electrolyte leakage. 6. Standard Test Condition 6.
Description Model ICP422339PR Rev. Page Rev.2.0 4/13 Lithium-ion Polymer Battery Pack 8. Test Procedure and its Standard Item Measuring Procedure 8.1 Appearance Visual Standard No Defects and Leakage 8.2 Dimension Caliper for dimension As item 4 8.3 Weight Balance As item 3.12 8.4 Initial Open Circuit Voltage 8.5 Initial Internal Impedance 8.6 Discharge Capacity Voltmeter 3.6~3.8V Measure the AC impedance at 1kHz ≤ 240mΩ (30% SOC) 8.
Model Description Rev. Page ICP422339PR Lithium-ion Polymer Battery Pack Rev.2.0 5/13 8.8 Charge/Discharge Cycle Life Charge: CC- 0.5C, CV-4.2V, Cut-off current: 0.05C Discharge capacity should be≧80% of 1st cycle capacity @ 500th cycle. 0.5C Rest for 10 minutes between each Discharge: 0.5C to 3.0V charge/discharge step. 8.9 Leakage Proof The fully charged battery shall be stored at No leakage. 65±3℃and relative humidity 95±5% for 7 days. Discharge capacities should 8.
Model ICP422339PR Description Rev. Page Lithium-ion Polymer Battery Pack Rev.2.0 6/13 10. Safety Criteria for Acceptance Item State Test method Specification External Short-circuit Fully Charged Cell terminals are short-circuited for 6 hours NO EXPLOSION or longer with a resistance of 80±20mΩor or FIRE. Test less. Tests are to be conducted at room temperature and 55℃. Forced-Discharge Fully Charged Cell is discharged at a current of 1C rate for NO EXPLOSION Test 1.5 hours.
Model ICP422339PR Description Rev. Page Lithium-ion Polymer Battery Pack Rev.2.0 7/13 11. Battery Pack Safety Criteria Item State Test method Specification Overcharge Test Fully Discharged Test passed according - Fully charge battery pack Settings: CVC mode: 4.2V, set charging to test method. current (0.8C), cut-off by taper current (or end Current) 0.02C. - Continuously charge battery pack Settings: CVC mode: 4.6V, set charging current (0.2C).
Model Description Rev. Page ICP422339PR Lithium-ion Polymer Battery Pack Rev.2.0 8/13 12. Charge State of Battery Before Shipment The battery is charged to 30 % of minimum capacity. Voltage is 3.6V~3.8V. This measuring test should be performed within one month after shipment from our factory. 13. Handling Precautions ICP battery pack shall have enough protection for ICP cell from the specification of electrical, mechanical and environmental characteristics.
Model Description Rev. Page ICP422339PR Lithium-ion Polymer Battery Pack Rev.2.0 9/13 (6) Don’t drive a nail into a battery, strike it by hammer, or tread it. As the battery might be broken or deformed and then it will be short-circuited, it would cause the generating, smoke, rupture or flaming. (7) Don’t give battery impact or fling it If the protection circuit assembled in the battery is broken, the battery will be charged at abnormal voltage or current and abnormal chemical reaction will occur.
Model Description Rev. Page ICP422339PR Lithium-ion Polymer Battery Pack Rev.2.0 10/13 (2) Don’t get into a microwave or a high pressure container Because of sudden heat or damage of sealing condition of battery, it may cause the generating, smoke, rupture or flaming. (3) Don’t use a leaked battery nearby fire If the liquid leaks from the battery (or the battery gives out bad smell), let the battery leave from flammable objects immediately.
Model ICP422339PR 14. History of Revision Description Rev. Page Lithium-ion Polymer Battery Pack Rev.2.0 11/13 REV. ISSUE CONTENT OF AMENDMENT PRE. CHK. APP. 1.0 Oct. 12, 2012 1st Edition MKL KS KW Mar. 10, 2016 2nd Edition Page 2 item 3.13、3.14、3.15 is changed. Page 4 item 8.4、8.5 is changed. Page 8 item 12 is changed. YHF KM KW 2.
Model Description Rev. Page ICP422339PR Lithium-ion Polymer Battery Pack Rev.2.0 12/13 Fig.
Model Description Rev. Page ICP422339PR Lithium-ion Polymer Battery Pack Rev.2.0 13/13 Part list: Item Ref Part name Number Qty 1 R1 RES 470Ω/±5% 1 2 R2 RES 1KΩ/±5% 1 3 R3 RES 4.7KΩ/±5% 1 4 C1, C2 CAP 0.1uF/+80-20% 2 5 U1 CONTROL IC S-8241AAXMC 1 SEIKO 6 U2 MOSFET STS8205 1 SAMHOP 7 -- PCB LW1804.28HFH-A 1 ASSUN or Same Spec Circuit diagram: Fig.
