User's Manual

FCC Compliance Statement
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reason-
able protection against harmful interference
in a residential installation. This equipment
generates, uses, and can radiate radio fre-
quency energy and, if not used in accordance
with the instructions, may cause harmful
interference to radio communications.
There is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase or decrease the separation
between the equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that which
the receiver is connected.
• Consult the dealer or an experienced
remote control/TV technician for help.
• It is strongly recommended that the TV
be plugged into a separate wall outlet.
The user is cautioned that changes and mod-
ications made to the equipment without the
approval of the manufacturer could void the
user’s authority to operate this equipment.
This device complies with part 15 of the FCC
rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
:Q Can I pair more than one
XFINITY Remote with the XR8
adapter?
:A Yes, the XR8 supports pairing
with up to ve XFINITY Re-
motes.
:Q Why can’t I use my other re-
motes after pairing my XFINITY
Remote with the XR8 adapter?
:A Some set-top boxes only
support XFINITY Remotes when
using the XR8. You can replace
your old remote with another
XFINITY Remote and pair it with
the XR8.
:Q During pairing, why does the
LED blink red and then green on
the XFINITY Remote?
:A Either a button other than the
XFINITY button was pressed,
or the XFINITY Remote timed
out before the XFINITY button
was pressed. Repeat the pairing
steps.
:Q During pairing, why does the
LED blink red, then green, then
red on the XFINITY Remote?
:A The XFINITY Remote you are
trying to pair cannot nd the
XR8. Unplug the XR8 and plug
it back in, making sure the
red LED on top of the adapter
turns on for 3-5 seconds. Then,
COMPATIBLE
DEVICES:
DTA
uDTA
RNG100
RNG110
RNG150
RNG150N
RNG200N
DCX3200
DCX3200-M
DCX3400
DCX3400-M
DCX3501
FREQUENTLY ASKED QUESTIONS
ABOUT THE AIM ANYWHERE ADAPTER
repeat the steps to pair the XR8
and XFINITY Remote. Be sure to
press the PAIR button on the XR8
before you press the XFINITY
button on your XFINITY Remote.
:Q When paired, why does the LED
blink green, then red on the
XFINITY Remote when a button is
pressed?
:A The XR8 may have lost power or
may be out of communication
range. Try moving closer to your
set-top box or DTA and make sure
the XR8 is securely connected. If
this does not x the issue, follow
the steps to re-pair the XR8 and
XFINITY Remote.
:Q Why is the XR8 adapter not re-
sponding to button presses from
my XFINITY Remote?
:A If the XR8 stops responding to an
already paired XFINITY Remote,
unplug the XR8 and plug it back
in. If this does not x the issue,
follow the steps to re-pair the XR8
and XFINITY Remote.
:Q Why does the LED continuously
blink when I plug in the XR8
adapter?
:A Your device is not compatible
with the XR8; please refer to the
“Compatible Devices” section for
a list of supported devices.
SET-TOP BOXES AND DTAS
The Aim Anywhere Adapter can be
used for out-of-sight control with the
set-top boxes and DTAs listed below:
XFINITY REMOTES
XFINITY Remotes that can be paired
with the Aim Anywhere Adapter
include:
XR2
XR5
XR11
XR13
For additional information
about XFINITY Remotes visit
xnity.com/remotes.
Note: The Cisco RNG200 is not com-
patible with the adapter.