Instructions / Assembly

• The “smoother” your wall is the better!
• Remove excess lint from roller nap by wrapping the roller in 2” masking tape, then remove the tape
and the excess lint will be removed with the tape.
• Always use a ReMARKable
TM
1/4" nap micro ber roller. Never use a foam or other synthetic roller.
• White ReMARKable
TM
should be applied over a “Pure White” painted background to ensure single coat
“opaque” coverage. Primer alone is not recommended. Primer goes through what is called an “o gas
sing” process and needs to “breath” for several weeks. Painting over primer works because standard
paint is porous and designed to “breath”, allowing the primer to properly o gas. ReMARKable
TM
is an
impervious coating and will not allow primer to “breath”, thus creating the possibility of causing “bubbles”
in the coating as it cures. Paint must dry at least 24 hours prior to ReMARKable
TM
application. Clear
ReMARKable
TM
can go over any pale to mid toned color, including white.
• Relative humidity needs to be below 50%.
• If you have a choice in the sheen of paint you are applying ReMARKable
TM
over, choose eggshell or
semi-gloss enamel for the best results. It does work over at paint, but at paint absorbs Remarkable
much faster, and if Remarkable is applied too thin in certain areas, it will not perform as well as it should.
An eggshell or semi-gloss enamel has a much more sealed surface allowing the Remarkable to sit more
on top of the nish as opposed to soaking into a at paint.
• Always keep the ambient room where you are applying ReMARKable
TM
at a consistent 68 – 77
degrees, during the 48-hour curing process.
• Gently, but thoroughly Mix part A and B for 3-4 minutes right before you are ready to apply it.
Do not use a mixer or drill or use a whipping motion. This can cause unwanted bubbles to occur during
the cure process.
• For White ReMARKable
TM
ONLY you may add 1-2% water to encourage easier ow. Do not add water
to clear ReMARKable
TM
.
• A 2” sponge brush works great for cutting in the ceiling, oor, and corners. Using the foam brush,
cut in as you go, Always working wet on wet.
• Apply a medium/heavy coat of ReMARKable
TM
to your substrate. It is important that you do not attempt
to “stretch” the product by applying it too thin. This will result in a failed application. Also, do not apply
ReMARKable
TM
too heavy or it will cause ReMARKable
TM
to “sag” or “run”, also causing a failed application.
For best results, fully saturate the micro ber roller nap with ReMARKable
TM
and apply it to the wall in a
vertical up and down motion. Always lead with the “heel” of the roller (See picture below) applying a slight
forward pressure toward the heel (gently twist the roller handle from left to right). Roll ReMARKable
TM
in
vertical patterns going up, then shifting the roller to the right, overlapping about 50% of your previous
pass, and roll downward and repeat, going back up and back down until you are nished with your
designated area. Do not overwork ReMARKable
TM
! Going over and over and over ReMARKable
TM
once it
has been applied to your substrate can and will most likely eect the lm forming process and cause a
failed application. If you have any questions before applying ReMARKable
TM
Please call Susan at:
800- 936-2159. We want you to have the best experience possible with ReMARKable
TM
.
NEVER mix an entire 600 square foot kit together all at one time.
Here are the ratios for measuring smaller areas.
4 oz Part A with 8 oz Part B covers 35 square feet
6 oz Part A with 12 oz Part B covers 50 square feet
12 oz Part A with 24 oz Part B covers 100 square feet
Slightly rotate the roer handle
from left to right applying a little
more pressure toward the hl. This
wi ensure a nice even spread of
ReMARKable™ and eliminate “Roer
Lines” in your wa.
Must be used within 6 months of purchase date.


Roller
Heel