Manual

9
OPERATION SPEAKERS
1. Set volume control to minimum level
Before switching on the device, turn the volume dials -1- & -14- to minimum position (dials all the way to the left).
2. Power ON
After all connections have been completed activate the device with the ON/OFF Switch -16-. The Power Status LED -4- and the Input Status
LED -5-will be lit.
3. Volume control
Adjust the volume with the corresponding dial -1-.
CAUTION!
Before switching on the power all volume controls of your nal amplier must be set to a minimum. Before increasing the volume wait 8 to 10
seconds to avoid damage to the loudspeakers.
OPERATION EXTERNAL WAVE CONTROL
1. Volume control
Adjust the volume with the corresponding dial -14-.
CAUTION!
Before switching on the power all volume controls of your nal amplier must be set to a minimum. Before increasing the volume wait 8 to 10
seconds to avoid damage to the loudspeakers.
2. Stand By / Mute
With this button it is possible to select two functions:
a) Mute
By presing this button -2- shortly, the device will switch to mute mode. The Input Status LED -5-, the Power Status LED -4- and the Reloop
sign on the device‘s upper side will start blinking. By pressing again, mute mode will be deactivated again.
b) Stand By
Press the button -2- for approximately 2 seconds; the device will switch to stand by. The Input Status LED -5-, the Power Status LED -4- and
the Reloop sign on the device‘s upper side will be dimmed. By pressing again for approximately 2 seconds, stand by mode will be deactivated
again.
3. Input Select Button
By pressing this button -3- it is possible to select the input source (XLR, jack or RCA). The corresponding LED -5- will be lit.
SOUND CONTROL
1. Use the HF Trim Switch -9- to lower or raise the high frequencies by - 2 dB or by +2 dB respectively, besides the normal position (0 dB).
This is very useful when using your passive monitors in larger rooms for example.
2. Use the Acoustic Space Switch -10- to adjust your speakers according to the set-up in the room (0 dB, -2 dB, -4 dB) since the acoustic pressure
in the low-frequency range is increased from the reection of adjacent surfaces. Distorted reproduction caused by positioning in corners or
near walls can be copensated this way.
3. Use the LF Cutoff Switch -11- to either fade the low-range frequency below 60 Hz, or 80 Hz or to bring it in the “Flat” position. This is very
useful when, for example, you intend to simulate the sound on a less bass-heavy speaker system or you are using an additional subwoofer or
want to suppress rumble noise.
TECHNICAL INFORMATION
Global Distribution GmbH did not test the following manufacturers’ specication for plausibility and accuracy:
Reloop Wave 5:
- Output capacity : RMS 50W, max. 100W
- Input sensitivity/impedance : +1.3dBu/20kohm (XLR & 6.3mm jack), -4.1dBu/20kohm (RCA)
- Tweeter : 2.5cm (1“) dome tweeter
- Woofer : 13cm (5“) paper cone woofer
- Maximum acoustic pressure : 102dB rated, 87dB RMS
- Frequency range : 32Hz - 20kHz (+/-3dB)
- Inputs : 1x XLR (symmetrical), 1x 6.3mm jack (symmetrical), 1x RCA (asymmetrical), 1x mini-DIN (controller)
- Dimensions : (w)185 x (h)320 x (d)230 mm (incl. cooling n)
- Weight : 6.0 kg (per speaker)
Reloop Wave 8:
- Output capacity : RMS 70W, max. 140W
- Input sensitivity/impedance : +0.5dBu/20kohm (XLR & 6.3mm jack), -5.5dBu/20kohm (RCA)
- Tweeter : 2.5cm (1“) dome tweeter
- Woofer : 20cm (8“) paper cone woofer
- Maximum acoustic pressure : 105dB rated, 90dB RMS
- Frequency range : 20Hz - 20kHz (+/-3dB)
- Inputs : 1x XLR (symmetrical), 1x 6.3mm jack (symmetrical), 1x RCA (asymmetrical), 1x mini-DIN (controller)
- Dimensions : (w)250 x (h)388 x (d)310 mm (incl. cooling n)
- Weight : 9.5 kg (per speaker)
Subject to alterations!
Illustrations similar to original product!
Misprints excepted!
ReloopTrademark
Global Distribution GmbH, Schuckertstr. 28, 48153 Münster, Germany, Fax [phone]
ENGLISCH