User Manual

ENGLISH
6
FIRMWARE UPDATE
!! Please check for any available rmware updates on www.reloop.com/reloop-ux !!
UPDATE INSTRUCTIONS FOR MACOS AND WINDOWS
Before proceeding, please make sure you have installed the latest Java Runtime Environment (JRE). You can download
and install Java from the following link: https://www.java.com/en/download/
Note: If you are using Microsoft EDGE, you may be unable to download the Java (JRE) application. If so, please
use a different browser for the download.
AFTER INSTALLING JAVA (JRE), PERFORM THE FOLLOWING STEPS:
1. Please make sure Serato DJ Pro or any other application is closed before performing the update.
2. Connect the FLUX to your computer via USB.
3. Launch the ReloopFirmwareUpdateApp application*, click “Open” and select the “FLUX_V***.bin” rmware le from
the download package. You will see the currently installed rmware version and the new version displayed inside the
updater.
4. Click “Start” and wait for the update (takes approximately 3~5 minutes).
5. Once nished, click “Close”.
The device‘s rmware has now been updated successfully and the FLUX is ready to use.
Note: In case of an issue or if the update takes longer than 20 minutes, disconnect the device and repeat the
instructions above.
*: If you receive a warning message on macOS, proceed as follows:
1. Go into your system preferences by clicking on the Apple icon and select “System Preferences”.
2. Select “Security & Privacy” and make sure the “General” tab is selected.
3. Click “Allow”.
The updater application should now open. If not, double-click the ReloopFirmwareUpdateApp application.
TECHNICAL SPECIFICATIONS
POWER:
- USB bus powered: Yes
- Recommended power: 2 A or higher
- Minimum power: 400 mA
- Maximum USB-PD throughput: 60 W
- Maximum USB Hub power output: 2 x 0.8 A = 8 W
- Supported external USB (type A or C) power supply: 5 V/1 A - 20 V/3 A
- Power supply priority: FLUX self-power -> USB Hub -> PD (to PC)
AUDIO:
- S/N Ratio (output reference level 1 kHz, +4 dB):
- Deck In (LINE signal input: 0 dBV): More than 83 dB
- Deck In (PHONO signal input: -32 dBV): More than 73 dB
- THD + N:
- LINE signal input: -4 dBV @1K / Less than 0.03% (1 kHz,+0 dB)
- PHONO signal input: -36 dBV @1K / Less than 0.05% (1 kHz,+0 dB,Inverse RIAA)
- Maximum Gain:
- Deck In (LINE): +4 dB ± 2 dB
- Deck In (PHONO): +36 dB ± 2 dB
- Maximum Input (1 kHz, THD=1%):
- Deck In (LINE): More than +7 dBV
- Deck In (PHONO): More than -25 dBV
- Maximum Output (1 kHz, THD=1%):
- Deck Output: More than +11 dBV
USB:
- USB audio interface with 24 bit/44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
- USB 2.0 high-speed (480 Mbit/s)
- Class-compliant
- USB Power Delivery Protocol 3.0
GENERAL:
- Dimensions (WxDxH): 160 x 120 x 34 mm
- Weight: 0.85 kg
ACCESSORIES:
- User Manual
- 1x USB type C/C cable
- 1x USB type C/A cable
- 2x RCA cables
SERVICE AND SUPPORT
For technical questions or issues, please check our FAQ or request a support ticket: https://www.reloop.com/faqs/