Instruction Manual

ENGLISH
12
V. OPERATION/POWER SUPPLY
ItispossibletooperateReloopSPINin3ways:
1. Battery Operation
InordertooperateReloopSPINwithbatteries,rstopentheBatteryCompartment-22-.Insert2loadedLi-Ion18650batteriesintothecompart-
mentandcloseitagain(batteriesnotincludedinthescopeofdelivery).YourReloopSPINisnowreadyforuse.
NOTE: When operating your Reloop SPIN via a USB PSU or USB power bank while batteries are inserted, they will be re-charged.
Remove the batteries, if you are not using the device for a longer period of time.
2. USB PSU Operation
YoucanalsooperateReloopSPINviaaUSBPSU(notincludedinthescopeofdelivery).Todoso,connectyourUSBPSUtotheUSBPSUInput
-21- of your Reloop SPIN.
NOTE: Please use a USB PSU with 2 ampere in order to guarantee awless operation.
3. USB Power Bank Operation
Also,youcanoperateReloopSPINviaaUSBpowerbank(notincludedinthescopeofdelivery).Todoso,connectyourUSBpowerbanktothe
USBPSUInput-21-.
NOTE: Please use a USB power bank with 5V/2A in order to guarantee awless operation.
VI. REPLACING THE CARTRIDGE NEEDLE
1. Remove the needle as displayed from the cartridge.
2. Place the needle as displayed into the cartridge.
3.Whenreplacingtheneedle,makesurethattherodandneedletiparealignedcorrectlyindirec-tionoftheanchor.
VII. TECHNICAL SPECIFICATIONS:
Type:  ...................................................... Beltdriven
Inputs: ...................................................... AUX3.5mmstereojack,Bluetoothaudio
Outputs: ...................................................... MasterRCA,USB(USB-A),headphones3.5/6.3mmstereojacks
Recordingformat: ......................................... MP3with256kbit/s
Recordingresolution: ................................... 16-Bit/44.1kHz
Batterytype: ................................................. 2xLi-Ion18650(batteriesnotincluded)
Powersupply: ................................................ 5V,2AminiUSB(PSUnotincluded)
Dimensions:.................................................... 370x95x260mm
Weight: ...................................................... 1.98 kg
Incl. 7‘‘ scratch vinyl, pre-installed cartridge, slipmat
Anker
Ausleger
Fassung
Nadel
FCC statement in User’s Manual (for class B)
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the Instructions , may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
1. This device complies with Part 15 of the FCC rules
Operation is subject to the following two conditions :
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that may cause undesired operation.
2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
3. Anychangesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser‘sauthority
to operate this equipment.
IMPORTANT NOTE : (For Mobile Device Configuration)
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
IM_SPiN_en.indd 12 12.02.2019 11:53:08