User Manual
Table Of Contents
- Deutsch
- Bestimmungsgemäße Verwendung
- Wartung
- 1. Aufbau
- 2. Inbetriebnahme
- 3. Computer Konfiguration
- 3.1 ASIO-Treiber Installation
- 3.2 Serato DJ Intro Installation
- 3.2.1 Serato DJ Intro Installation / Windows
- 3.2.2 Serato DJ Intro Installation / Mac OSX
- 3.3 Virtual DJ LE 4-Deck Reloop Edition Installation
- 3.3.1 Virtual DJ LE 4-Deck Reloop Edition Installation / Windows
- 3.3.2 Virtual DJ LE 4-Deck Reloop Edition Installation / Mac OSX
- 3.4. Traktor Unterstützung
- 4. Bedienung
- 5. Geräteeinstellungen und -tests
- 6. Anhang
- 6.4 Technische Daten
- English
- APPLICATION IN ACCORDANCE WITH REGULATIONS
- MAINTENANCE
- 1. Setup
- 2. Initial Operation
- 3. Computer Configuration
- 3.1 ASIO Driver Installation
- 3.2 Serato DJ Intro Installation
- 3.2.1 Serato DJ Intro Installation / Windows
- 3.2.2 Serato DJ Intro Installation / Mac OSX
- 3.3 Virtual DJ LE 4-Deck Reloop Edition Installation
- 3.3.1 Virtual DJ LE 4-Deck Reloop Edition Installation / Windows
- 3.3.2 VirtualDJ LE 4-Deck Reloop Edition Installation / Mac OSX
- 3.4 Traktor Support
- 4. Operation
- 5. Device Settings and Tests
- 6. Appendix
- Francais
- UTILISATION CONFORME
- ENTRETIEN
- 1. Installation
- 2. Mise en service
- 3. Configuration de l‘ordinateur
- 3.1 Installation du pilote ASIO
- 3.2 Installation Serato DJ Intro
- 3.2.1 Installation Serato DJ Intro / Windows
- 3.2.2 Installation Serato DJ Intro / Mac OSX
- 3.3 Installation Virtual DJ LE 4-Deck Reloop Edition
- 3.3.1 Installation Virtual DJ LE 4-Deck Reloop Edition / Windows
- 3.3.2 Installation Virtual DJ LE 4-Deck Reloop Edition /Mac OSX
- 3.4 Prise en charge de Traktor
- 4. Utilisation
- 5. Réglages et tests de l‘équipement
- 6. Annexe
- 6.4 Caractéristiques
- Español
- Uso conforme al destino previsto
- Mantenimiento
- 1. Estructura
- 2. Puesta en marcha
- 3. Configuración del ordenador
- 3.1 Instalación del controladorASIO
- 3.2 Instalación de Serato DJ Intro
- 3.2 Instalación de Serato DJ Intro / Windows
- 3.2 Instalación de Serato DJ Intro / Mac OSX
- 3.3 Instalación Virtual DJ LE 4-Deck Reloop Edition 3.3.1 Instalación Virtual DJ LE 4-Deck Reloop Edition / Windows
- 3.3.2 Instalación Virtual DJ LE 4-Deck Reloop Edition / Mac OSX
- 3.4 Soporte Traktor
- 4. Manejo
- 5. Pruebas y ajustes del equipo
- 6. Anexo
- 6.4 Datos técnicos
28
Terminal Mix 4 disposes of different routing possibilities in order to include already existing equipment.
A microphone can be connected via a 6.3 mm jack on the device‘s front panel -F53-. Besides the volume dial -F54- a routing switch -F56- is also
integrated which controls the following routing options:
SW = The microphone signal is routed to the software.
MST = The microphone signal is directly routed to the device‘s master-out.
Moreover it is possible to manipulate the microphone signal via the included Equalizer -F55-.
At the device‘s side you have the possibility to connect an external sound source via RCA cable to the Terminal Mix 4 (-B51-) and integrate it in
the controller. There is also the possibility to route the signal directly to the master output or to a software.
In order to route the signal directly to the master output please put the Input Routing Switch -F57- on the device‘s front side in the MST posi-
tion. Now you can control the input level via the Volume Dial -F58-. Additionally to a line-in source you also have the possibility to connect a
turntable. To do so please put the Line/Phono Switch -B50- in the “PH” position.
If you wish to route the signal to a software, put the Input Routing Switch -F57- in the “SW” position.
On the rear panel of Terminal Mix 4 you can nd three stereo outputs. Master 1 -B47- (RCA) as well as Master 2 -B46- (symmetrical 6.3 mm jack)
can be adjusted via the Master Volume Encoder -T30-.
The booth output -B48- (RCA output) can be adjusted via the Booth Dial -T31-.
Several adjustments and tests can be carried out with Terminal Mix 4 without the help of a computer. In the following a few of these items are
explained in detail.
To see the current rmware version of the Terminal Mix 4 proceed as follows:
1. Make sure that Terminal Mix 4 is turned off (see position On/Off Switch -B44-).
2. Hold TRAX + CRATES + VIEW simultaneously and turn on the device.
Now different LED statutuses will be shown on the device; these are assembled in three different sections (X.YZ).
Example: In X section no LED is illuminated, in Y section 1 LED is illuminated and in Z section 3 LEDs are illuminated. This corresponds to the
rmware version 0.13. By pressing the TRAX Encoder -T39- again the device will reboot.
You can adjust the LEDs‘ intensity. Simultaneously the functionality of all LEDs can be checked.
1. Make sure that Terminal Mix 4 is turned off (see position On/Off Switch -B44-).
2. Hold TRAX + BACK + PREP simultaneously and turn on the device.
By turning the TRAX Encoder -T39- you can now adjust the LED intensity. By pushing the TRAX Encoder -T39- again the value will be stored and
the device will be rebooted.
Terminal Mix 4 offers the possibility to adjust the jog wheel sensitivity.
1. Make sure that Terminal Mix 4 is turned off (see position On/Off Switch -B44-).
2. Hold TRAX + BACK + CRATES simultaneously and turn on the device.
3. Turn deck A‘s MOVE Encoder -T12- to adjust the desired value of jog wheel A.
4. Turn deck B‘s MOVE Encoder -T12- to adjust the desired value of jog wheel B.
There is a total of 10 adjustment possibilities that are displayed by LED statuses in the Hot Cue and Sample section. By pressing the Trax Enco-
der again the value will be stored and the device will reboot.
Add all illuminated LEDs from the left Hot
Cue -T13-, Sample -T15- & Jog Wheel Mode
button -T16-. If nothing is displayed, this
corresponds to a value of 0.
Add all illuminated LEDs from the right Hot
Cue -T13-, Sample -T15- & Jog Wheel Mode
button -T16-. If nothing is displayed, this
corresponds to a value of 0.
Add all illuminated LEDs from the transport
section -T19- – -T23-. If nothing is displayed,
please repeat steps 1 & 2.