User's Manual

50
KNG User’s Manual
51
RELM/BK Radio
Bandwidth
Bandwidth selection in only valid for channels programmed to transmit
in analog mode.

Bandwidth
Narrowband
Wideband
ESC ▲ ▼ ENTER
Select 'Bandwidth' from the menu. 1.
Use the up/down arrows to select 2.
Narrowband (12.5 kHz) or Wideband (25 kHz).
Press the 'ENTER' button to set the mode 3.
and return to the programming menu.
Low Power Lock
Channels with Low Power Lock enabled ignore the Hi/Lo power switch
and operate in Low Power only.

Low Power Lock
Off
On
ESC ▲ ▼ ENTER
Select 'Low Power Lock' from the menu. 1.
Use the up/down arrows to select On or 2.
Off.
Press the 'ENTER' button to set the mode 3.
and return to the programming menu.
Transmit Frequency
ESC CLEAR EDIT
Tx Frequency
151.625000
Tx Frequency
000.000000
ESC BACK NEXT ENTER
1. Select Tx Frequency' from the menu.
2. Press the 'CLR' or 'EDIT' button to program
the frequency.
2. Use the keypad to select the desired
frequency. (136 - 174 MHz)
3. Press the 'ENTER' button to set the
frequency and return to the programming list.
Transmit Mode

Tx Mode
Analog
Digital
Mixed
ESC ▲ ▼ ENTER
1. Select 'Tx Mode' from the menu.
2. Use the up/down buttons to select the
desired receive mode.
3. Press the 'ENTER' button to save the
setting and return to the programming list.
Transmit Code Guard

Tx Guard
Off
Tone ->
Digital->
ESC ▲ ▼ ENTER
Tx Guard
Off
Tone -> 100.0Hz
Digital ->
ESC ▲ ▼ ENTER
Tx Guard
Off
Tone ->
Digital -> D131
ESC ▲ ▼ ENTER
NOTE: Code Guards are available only on
channels programmed for analog or mixed
mode operation.
Select 'Tx Guard' from the menu.1.
The arrow indicates the currently programmed
Code Guard for analog signals.
Use the up/down buttons to select the 2.
desired Code Guard type.
Off = No tone
Tone=CTCSS
Digital=CDCSS
Select=Code Guard selected from
User Code Guard list.
Use the keypad to program the desired 3.
Code Guard. (See below)
Tone - CTCSS Tone
Guard Tone
100.0 Hz
ESC CLEAR EDIT
Guard Tone
000.0 Hz
ESC BACK NEXT ENTER
Select 'Tone' from the menu.1.
Press the 'CLEAR' button to clear the 2.
currently programmed tone or press the or
'EDIT' button to edit the tone.
To enter CTCSS tones use the keypad to 3.
enter the tone in Hertz. (67.0 - 255 Hz)
Press the 'ENTER' button to set the tone 4.
and return to the programming menu.
Digital - CDCSS Tone
Guard Tone
D121
ESC CLEAR EDIT INV
Guard Tone
121
ESC BACK NEXT ENTER
Guard Tone
D121-
ESC CLEAR EDIT INV
Inverted DCS Tone
Select 'Digital' from the menu.1.
Press the 'CLEAR' button to clear the 2.
currently programmed code guard or press the
or 'EDIT' button to edit the guard.
To enter CDCSS tones use the keypad 3.
to enter a three digit code guard. (000 - 999)
Press the 'ENTER' button to set the 4.
tone and return to the programmable menu.
NOTE: If an inverted CDCSS is desired, press
the 'INV' button prior to editing the code guard.