User's Manual

56
KNG User’s Manual
57
RELM/BK Radio
Receive Code Guard
RX Guard
000.0
ESC CLR ENT
Rx Guard
Rx NAC
Squelch Mode
ESC ▲ ▼ ENT
ESC CLR ENT
RX Guard
000.0
1. With 'Rx Guard' highlighted, press the 'ENT'
button.
2. Press the 'CLR' button to clear the
currently programmed tone.
3. To enter CTCSS tones use the keypad to
enter the tone in Hertz. (67.0 - 255 Hz) To enter
CDCSS tones press the # key then enter the
three digit code. (000 - 999)
4. Press the 'ENT' button to set the tone.
5. Press the 'ESC' button to return to the
Channel Programming menu.
Receive Network Access Code
RX NAC
000
ESC CLR ENT
Rx Guard
Rx NAC
Squelch Mode
ESC ▲ ▼ ENT
ESC CLR ENT
RX NAC
293
1. With 'Rx NAC' highlighted, press the 'ENT'
button.
2. Press the 'CLR' button to clear the
currently programmed NAC.
3. Use the keypad to select the Þ rst digit.
4. Press the PR1 button to move to the next
character. NACs are programmed as three
digit hexadecimal numbers. (000 - FFF)
5. Press the 'ENT' button to set the NAC.
6. Press the' ESC' button to return to the
Channel Programming menu.
Squelch Mode
Squelch Mode
→
Normal
Selective
ESC ▲ ▼ ENT
Rx Guard
Rx NAC
Squelch Mode
ESC ▲ ▼ ENT
1. With 'Squelch Mode' highlighted, press the
'ENT' button.
2. Use the up/down arrows to select Normal
or Selective. (Selective squelch is required for
Individual Calls and use of Talkgroup IDs.)
3. Press the 'ENT' button to set the selection.
4. Press the 'ESC' button to return to the
Channel Programming menu.
Transmit Frequency
TX Frequency
151.62500 MHz
ESC CLR ENT
Squelch Mode
Tx Freq
Tx Mode
ESC ▲ ▼ ENT
ESC CLR ENT
TX Frequency
000.00000 MHz
1. With 'Tx Freq' highlighted, press the 'ENT'
button.
2. Press the 'CLR' button to clear the current
frequency.
3. Use the keypad to select the desired
Receive Frequency.
4. Press the 'ENT' button to set the frequency.
5. Press the 'ESC' button to return to the
Channel Programming menu.
Transmit Mode
TX Mode
→
Digital
Mixed
ESC ▲ ▼ ENT
Squelch Mode
Tx Freq
Tx Mode
ESC ▲ ▼ ENT
1. With 'Tx Mode' highlighted, press the 'ENT'
button.
2. Use the up/down buttons to highlight the
desired Transmit Mode. (Analog, Digital or
Mixed)
3. Press the 'ENT' button to set the mode.
4. Press the 'ESC' button to return to the
Channel Programming menu.
Channel Bandwidth
Bandwidth selection applies only to Analog operation.
TX Mode
→
12.5 kHz
25 kHz
ESC ▲ ▼ ENT
Tx Freq
Tx Mode
Bandwidth
ESC ▲ ▼ ENT
1. With 'Bandwidth' highlighted, press the
'ENT' button.
2. Use the up/down buttons to highlight
the desired Analog Bandwidth. (12.5 kHz =
narrowband, 25 kHz = wideband)
3. Press the 'ENT' button to set the selection.
4. Press the 'ESC' button to return to the
Channel Programming menu.