User's Manual

ManualsBrandsRELM WIRELESS CORP. - BK RADIO ManualsElectronicsMOBILE LAND MOBILE TRANSCEIVER

Table Of Contents

Introduction
FCC Requirements
Industry Canada Compliance
Information and Options
Radio Controls
LCD Touch Screen
- Status Indicators
- Channel Information Display Options
- Programmable Button and Menu Options
Microphone Controls
Function Selection
- Touch Screen Selection
- Navigation Wheel Selection
- Menu Screen Selection
Channel/Zone Selection Options
Basic Operation
Trunking Channel Basic Operation
Command Zone Operation
- Building a Command Zone [CHAN+]
- Editing a Command Zone [CHAN-]
Code Guard/NAC Operation
- Code Guard Receive
- Code Guard Transmit
- Analog Squelch Control
- APCO Project 25 Digital Squelch Control
Mixed Mode Operation
Scan Options
- Channel Scan [SCAN]
- Channel Scan List [SCN+]
- Talkback Scan
- Dual Mode Scan [DSCN]
- Dual Mode Scan List [DSED]
- Enhanced Scan [ESCN]
- Priority Scan/System Scan [PSCN]
- Priority Channel Select [PRI]
- Vote Scan
- Zone Scan [ZSCN]
- Zone Scan List [ZSC+]
Encryption Operation
- Required Setup
- Transmit Secure [SEC]
- Transmit Encryption Key Selection [KEY]
- Encryption Keyset Selection [KEYST]
- Rekey Request [RKEY]
- Keyset Viewing and Selecting [KSET]
- Zeroizing [ZERO]
User Pick List Options
- TX/RX CxCSS Picklist [TXCG] [RXCG]
- TX/RX Network Access Code Picklist [TNAC] [RNAC]
- Talk Group ID Picklist [TGID]
- Encryption Key Picklist [KEY]
- Keyset Picklist [KSET]
Emergency Signaling
Messaging Options
- Text Messaging [TXT]
- Short Message Update [MSG]
- User Status Messaging [STS]
Paging and Call Alert
- Conventional Two-Tone/DTMF/MDC1200 Paging [MUTE]
- Call Alert Paging [ALRT]
- Radio Check [RCHK]
Other Functions & Options
- Backlight [LITE]
- Cloning
- Control Lockout [LOCK]
- Date and Time [DATE]
- Global Positioning [GPS]
- Hard Power Down [PWRD]
- Home [HOME]
- Inhibit/Uninhibit [INH]/UINH]
- Keypad Programming
- Minimum Volume [VOL]
- Monitor [MON]
- Nuisance Channel Delete [NUIS]
- Phone [PHN] and Hang Up [HANG]
- Radio Accountability Tone [RAT]
- Radio Info
- Repeater Talkaround [T/A]
- Send Alert Tone [SNDT]
- Send Signal [SEND]
- Squelch Adjust [SQL]
- Site Display [STDS]
- Site Lock [STLK]
- Site Search [STSR]
- Surveillance Mode [SURV]
- Transmit Digital [TXD]
- Transmit Power [PWR]
- Two-Tone Select [TONE]
- Versions
- Zone Select [ZONE]
Keypad Programming Options
- Entering Programming Mode
- Keypad Programming
- Call List Programming
- Code Guard Picklist Programming
- NAC Picklist Programming
- Talkgroup ID Picklist Programming

- 63 -

KNG Mobile Operation

Receiving an Emergency Call

When the radio receives an Emergency Call, "EMERGENCY" and the incoming

P25 ID or MDC number or label will be displayed during the reception. An alert tone

will be emitted if the radio is programmed to do so.

Emergency Alarm (Emergency Alert)

Press and hold the button to initiate an Emergency Alarm mode.

Once Emergency Alarm is initiated, the emergency message is transmitted

automatically. The radio will emit a series of beeps and "EMERGENCY" will ash

on the display. "EMERGENCY" and the incoming P25 ID or MDC number or label

will be displayed on the receiving radio. An alert tone will be emitted if the radio is

programmed to do so.

NOTE: When the emergency alarm is broadcast for digital operation, the radio

will not receive the signal while a scan is active (Priority, Channel, Zone) unless

the following conditions are met: 1) the Data Mode for the Emergency Channel of

the TX Radio (radio declaring the emergency) needs to be Repeated or Direct (not

FNE); and 2) the Data Scan Hold Time on RX radios needs to be non-zero. Analog

channels will work while scanning without any special settings on either radio.