User's Manual

ManualsBrandsRELM WIRELESS CORP. - BK RADIO ManualsElectronicsMOBILE LAND MOBILE TRANSCEIVER

Table Of Contents

Introduction
FCC Requirements
Industry Canada Compliance
Information and Options
Radio Controls
LCD Touch Screen
- Status Indicators
- Channel Information Display Options
- Programmable Button and Menu Options
Microphone Controls
Function Selection
- Touch Screen Selection
- Navigation Wheel Selection
- Menu Screen Selection
Channel/Zone Selection Options
Basic Operation
Trunking Channel Basic Operation
Command Zone Operation
- Building a Command Zone [CHAN+]
- Editing a Command Zone [CHAN-]
Code Guard/NAC Operation
- Code Guard Receive
- Code Guard Transmit
- Analog Squelch Control
- APCO Project 25 Digital Squelch Control
Mixed Mode Operation
Scan Options
- Channel Scan [SCAN]
- Channel Scan List [SCN+]
- Talkback Scan
- Dual Mode Scan [DSCN]
- Dual Mode Scan List [DSED]
- Enhanced Scan [ESCN]
- Priority Scan/System Scan [PSCN]
- Priority Channel Select [PRI]
- Vote Scan
- Zone Scan [ZSCN]
- Zone Scan List [ZSC+]
Encryption Operation
- Required Setup
- Transmit Secure [SEC]
- Transmit Encryption Key Selection [KEY]
- Encryption Keyset Selection [KEYST]
- Rekey Request [RKEY]
- Keyset Viewing and Selecting [KSET]
- Zeroizing [ZERO]
User Pick List Options
- TX/RX CxCSS Picklist [TXCG] [RXCG]
- TX/RX Network Access Code Picklist [TNAC] [RNAC]
- Talk Group ID Picklist [TGID]
- Encryption Key Picklist [KEY]
- Keyset Picklist [KSET]
Emergency Signaling
Messaging Options
- Text Messaging [TXT]
- Short Message Update [MSG]
- User Status Messaging [STS]
Paging and Call Alert
- Conventional Two-Tone/DTMF/MDC1200 Paging [MUTE]
- Call Alert Paging [ALRT]
- Radio Check [RCHK]
Other Functions & Options
- Backlight [LITE]
- Cloning
- Control Lockout [LOCK]
- Date and Time [DATE]
- Global Positioning [GPS]
- Hard Power Down [PWRD]
- Home [HOME]
- Inhibit/Uninhibit [INH]/UINH]
- Keypad Programming
- Minimum Volume [VOL]
- Monitor [MON]
- Nuisance Channel Delete [NUIS]
- Phone [PHN] and Hang Up [HANG]
- Radio Accountability Tone [RAT]
- Radio Info
- Repeater Talkaround [T/A]
- Send Alert Tone [SNDT]
- Send Signal [SEND]
- Squelch Adjust [SQL]
- Site Display [STDS]
- Site Lock [STLK]
- Site Search [STSR]
- Surveillance Mode [SURV]
- Transmit Digital [TXD]
- Transmit Power [PWR]
- Two-Tone Select [TONE]
- Versions
- Zone Select [ZONE]
Keypad Programming Options
- Entering Programming Mode
- Keypad Programming
- Call List Programming
- Code Guard Picklist Programming
- NAC Picklist Programming
- Talkgroup ID Picklist Programming

- 41 -

KNG Mobile Operation

Talk in a normal voice with the microphone one to two inches from your 2.

mouth.

Release the PTT switch to stop transmitting.3.

Analog Squelch Control

Sub-audible signaling (CTCSS/CDCSS) is used to allow a group of radios to be

selectively called in an analog system. Programming the receive code guard equal to

zero turns o󰀨 this feature while receiving, and allows for Carrier Squelch operation,

where the radio will unmute whenever a carrier is detected regardless of the

transmitted Code Guard.

APCO Project 25 Digital Squelch Control

Network Access Codes (NACs) provide the digital equivalent of analog sub-audible

signaling (CTCSS/CDCSS), allowing a group of radios to be selectively called within

a system.

Users in the same area (using the same NAC) can be further divided into Talk

Groups, with each group having its own Talk Group ID (TGID). Group Calls are made

by designating both the users’ NAC and TGID.

Each radio also has an individual P25 unit ID. A Unit-to-Unit call contains the

addressee’s NAC, and uses the addressee’s P25 unit ID instead of the TGID.