AC Controller--ShowDoc

ManualsBrandsRejeee ManualsData Communication and Human Input DevicesLoRaWAN AC Remote Controller

CT100EU AC Controller

The max power is 22dbm, the transmission distance reach 3~5 km in open area

Built in 30A relay, switching power up to 3kw

With scene combination function and timing switch

It has current, voltage and power monitoring functions

With status report feedback function

With on-site manual operation function

Open communication protocol, support Lora transparent transmission and lorawan protocol, and access the

third-party Lora gateway with simple configuration

Parameter Feature

CPU STM32L151

Wireless LoRa（SX1268/SX1262）

Encryption AES128

Power 200~240V AC，50HZ

Measuring Load AC 0~16A

Sleep Power less then 2.5W

Commnunication half-duplex

Data Speed 300bps ~ 62.5 kbps

TX Power Max 22dBm

Sensitivity -140 dBm

Antenna SMA

Frequency

SX1268: CN470

SX1262: AS923 EU868 US915

sIZE 112mm X 65mm X 55mm

Working Temperature -40℃~85℃

Working Humidity 10%~90%RH

Housing PC

Installation 35mm standard guide rail

1.1.Product Feature

1.2.Product Parameters

1.3.Product Detail

Summary of content (8 pages)

PAGE 1
CT100EU AC Controller 1.1.Product Feature The max power is 22dbm, the transmission distance reach 3~5 km in open area Built in 30A relay, switching power up to 3kw With scene combination function and timing switch It has current, voltage and power monitoring functions With status report feedback function With on-site manual operation function Open communication protocol, support Lora transparent transmission and lorawan protocol, and access the third-party Lora gateway with simple configuration 1.2.
PAGE 2
Pic 1-1 Front 1.4.
PAGE 3
Pic 1-2 Installation Pic 1-3 Use Example 1. LoRa Antenna 2. Status Indicator（Red indicates that the relay is open and green indicates that the relay is closed） 3.
PAGE 4
. Press the key manually to close, press the key briefly to disconnect the relay 5. Configuration Port 6. AC output _ 7. AC output + 8. AC input _ 9. AC input + 1.5.Attentions 1. please follow the correct wiring identification diagram for wiring. Incorrect wiring may cause equipment damage 2. please cut off the power supply when wiring. Live wiring may cause electric shock 3. please strictly equip the load and do not overload 4.
PAGE 5
The default uploading period is 600s as heartbeat transmission. That means from factory set, the controller upload information every 10mins, and it is configurable according to real applications. 3.3.Wireless LoRa Parameters As there are too many LoRa parameters, you can refer to Rejeee AT command. 3.3.1 Configuration under LoRaWAN Below picture is CN470 for reference. Frequency should be the same as LoRaWAN Server(NS).
PAGE 6
Under LoRaWAN, ABP is SPI=02，OTAA is SIP=03，SF is configurable. In LoRaWAN mode, users can decide whether to modify APPEUI and appKEY as needed. Just keep consistent with LoRaWAN server. Other relevant parameters do not need much attention. LoRaWAN server will perform rate adaptive ADR operation (automatically modify frequency point, SF and power) according to communication quality. In ABP mode, the appKEY of the device is used to configure appKEY and networksKEY. The two KEYs are shared. 3.3.
PAGE 7
4.2 Sensor Data 4.2.1 Device information（0x00） Type Value Value Value 1 Byte 3 bit 5bit 1 Byte 0x00 Version Battery Level Reserve 4.2.2.On/off（0x09） In most cases, a device has only one channel of switching value, but it meets the status indication of up to eight channels of switching value. Type Value 1 Byte 1 Byte Comment 1-byte unsigned integer. The specific meaning depends on the 0x09 item.
PAGE 8
outData ^= outData << 12; outData ^= (outData & 0xff) << 5; return outData; } .