Operating Instructions jetStamp 790 MSL Mobile electronic hand stamp with flexible impression selection
© 2006 Ernst Reiner GmbH & Co. KG All rights reserved. Translations, reprints, or any other form of reproduction of this manual, even in part and regardless of form, require prior written permission. This manual is subject to change without prior notice. This manual has been compiled with the utmost care and diligence, however we cannot assume any form of liability for errors or omissions or for damage resulting from them.
Table of contents Content Page Control elements ......................................................................................... 4 Commissioning .............................................................................................5 Display zones and button functions ............................................................ 6 Setting time and date ...................................................................................7 Select a Stamp picture .................................
Control elements 4 5 6 7 8 1 9 2 3 1 2 3 4 5 6 7 8 9 4 = = = = = = = = = Base station with mains unit Socket for power supply Green charge-indicator lamp Trigger Display Buttons Locking rail Ink cartridge Notch
Commissioning Unpack the stamp, connect the mains unit to the charging station, plug in the mains unit, and switch on the power supply. Note: Use only original REINER components! Place jetStamp in the charging station, take care of the following points: • Engage the notch (9) and place jetStamp in the charging station • Allow at least 14 hours for the first charging, subsequently, approximately three hours are required for charging.
Display zones and button functions The display is divided into three zones: A The top line is the status line. On the left is the number of the impression selected (P:26 ... P:29) . To the right of that, the Moisture Sensivity Level is displayed (MSL: 1, 2, 2A, 3, 4, 5, 5A, 6) At the right of the top line is the battery symbol, showing the state of charge of the battery. B The middle of the display shows the impression currently selected on one or two lines.
Setting time and date First select an impression that contains the date, or date and time as appropriate Press [ MODE ] if necessary repeatedly, until the menu item “CLOCK” is displayed Press [ CLOCK ] to select the required menu item The display shows “INPUT - TIME 1” and below it you will see the time currently set i This menu may be protected by a password. In that case the correct password must first be entered.
Select a stamp picture i • A total of four different stamp pictures are stored. These contain the individual printing fields 'Date' and 'Time’ . • The stamp pictures are numbered 'P:26' to 'P:29'. The number of the stamp picture currently selected is shown at the top left of the display • The following formats of the date are assigned to the different Stamp pictures: Note Stamp picture P:26 Stamp picture P:27 Day, Month, Year, Time of day Year, Month, Day, Time of day P : 26 MSL: 2A OPEN 12.
Descriptions of the Stamp pictures P : 26 MSL: 2A OPEN 12. 07. 06 13:23 USED 09. 08. 06 13:23 CLOCK i INC NEXT MODE • Each Stamp picture includes two lines with respective 20 possible input characters Note • All Stamp pictures are assigned with the fields Date 1 , Date 2 , Time 1 and Time 2 . With application of a PC-Set the Stamp pictures can be reserved individual with the corresponding fields. Following this fields can be selected for data input.
Time on Label Special function MSL: 06 By pressing [ INC ] the timing can be add up by one hour within of 23 hours. The alternation of days will be taken into account. Display example: P : 26 MSL: 06 OPEN 01. 10. 06 13:45 USED 01. 10.
Changing text blocks Entry of characters: Select the desired stamp picture (P:26 ...
Stamping Stamping will be triggered by pressing the red trigger, which is located in the grip. Depending on the impression selected, the impression will have one or two lines. The position of the two lines, relative to the base of the stamp, can be seen in the illustration below. i Note • Stamping may be protected by a password. In that case the correct password must first be entered. To block stamping again, press [ MODE ] repeatedly until 'CLOSE' appears in the menu bar.
Changing the ink cartridge i • The change of the ink cartridge may be necessary if the imprint is incomplete or if dots are missing Note • For an optimal print performance the ink cartridge should be changed at least all six months • The ink cartridge is ready to print that neans there is no preparation necessary before using it • Replacement ink cartridges are available with the order number 801 307 - 000 on REINER stock The ink in the ink cartridge is harmful.
Dirt and dried up ink at the holder of the ink cartridge can be removed with a soft cleaning cloth moistened in spirit (see figure 2) 2 Insert the new ink cartridge: Take the ink cartridge from the packaging and remove the coloured protection film from the ink cartridge (see figure 3) 3 Residual ink on the silver plate can be removed with a soft cloth (see figure 4) Put in the new ink cartridge into the ink cartridge holder 4 Push the locking clip upwards until it engages, by this means the ink cartri
Setup module The Setup module contains the following two main menus: SETTINGS: Enables comprehensive, extensive changes to settings to be carried out, which, among other things, influence the impression and the handling of the stamp. UPDATE: In combination with the optional PC - Set, the program in jetStamp can be updated. In addition, the impressions P:26 ... P:29 can be individually replaced or modified.
Description of the Setup module MODE Press, repeatedly if necessary SETUP (Enter password if required) SETTINGS CALL NEXT UPDATE CALL FIRMWARE ALL NEXT See next page FIRMWARE PART NEXT STAMP PICTURE NEXT PRE TEXT START Update firmware, standard impressions and standard pre-texts.
SETTINGS UPDATE NEXT CALL MS LEVEL VARY activation of a MS - Level (MS = Moisture Sensivity) NEXT 1 2 2A 3 4 5 5A 6 = = = = = = = = Unlimited 1 year 4 weeks 7 days 3 days 2 days 1 day Time on Label Notice : Preset MS - Level will be displayed in the status line of the display STAMP PICTURE VARY activation of a Stamp picture (26 ...
LANGUAGE VARY 0 3 6 9 NEXT SPLIT HOUR 60M VARY VARY VARY NEXT German 1 = French Italian 4 = Spanish Flemish 7 = Norwegian Danish 2 = English 5 = Portuguese 8 = Swedish = one hour = 60 minutes = one hour = 100 sub-divisions Summer time (0 ...
MODE NUM 1 VARY 1 = increase to a maximum value 2 = decrease to a minimum value NEXT SKIP NUM 1 VARY VARY VARY NEXT Step setting for numbering device 2 Step can be set between 0 and 99 NEXT PRT CARTRIDGE Mode setting for numbering device 2 1 = increase to a maximum value 2 = decrease to a minimum value NEXT SKIP NUM 2 Step setting for numbering device 1 Step can be set between 0 and 99 NEXT MODE NUM 2 Mode setting for numbering device 1 VARY Ink cartridge settings 1 = standard ink cart
BLOCK IMPRINT VARY 0 1 2 3 NEXT PASSW SETUP Adjustment of Block imprint = = = = Imprint Imprint Imprint Imprint not blocked blocked after 60 seconds blocked after 30 seconds blocked after 15 seconds * VARY Password for Setup VARY Password for time setting VARY Password for numbering device / pre-texts * VARY Password for stamping NEXT PASSW CLOCK * NEXT PASSW NO/TXT NEXT PASSW PRINT * NEXT back to MS LEVEL see page 18 * Password setting: Select desired menu item with [ VARY ] then
Troubleshooting Display Cause Recommendation IMPRINT Time allowed by ‘Block Imprint’ BLOCKED has expired, disappears trigger has been pressed Press [ QUIT ] : jetStamp is then ready for use again WRONG STATION Wrong base station, jetStamp needs an intelligent base station Press [ QUIT ] : Error message disappears and previous display reappears Error 04 Memory error Press [ QUIT ] Error 09 - Sensor or motor defective - print carriage blockade Press [ QUIT ] and start stamping again Reset button
Technical data Stamping time approx. 0,7 seconds Stamping cycle > 2 seconds Print capacity per ink cartridge approx. 300.000 characters Stand by time per battery charge 6 days or 500 stampings Time to charge battery approx. 3 hours Dimensions, jetStamp 790 only (B x D x H in mm) Dimensions, charging station only (B x D x H in mm) 102 x 135 x 32 Height of jetStamp in charg. stat. 187 mm Weight of jetStamp 790 approx. 490 g Weight of charging station approx.
ERNST REINER GMBH & CO. KG Postfach 1351 D - 78115 FURTWANGEN Telephone Fax E-Mail Internet + 49 7723 6570 + 49 7723 657200 reiner@reiner.de www.reiner.
