• CEILING FAN OWNER’S MANUAL • • LX SERIES • 5/04 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
GENERAL INSTALLATION & OPERATION INSTRUCTIONS IMPORTANT SAFEGUARDS: 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS Thank you for choosing a Regency Ceiling Fan. You have chosen the best! Your new ceiling fan has been designed to provide many years of service and enjoyment. Warnings: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting. Support directly from building structure.
UNPACKING YOUR FAN 1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. 2. Examine all parts. You should have the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
PREPARATION Parts identification on assembled fan Uplights (on top of fan motor housing) Canopy Collar Cover Downrod Blade Motor Housing Blade Arm Detachable Switch Housing Pull Chain Pull Chain PREPARATION: Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box.
INSTALLING THE FAN ATTACH DOWNROD: 1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. 3. Feed the wires from top of fan through end of downrod you have chosen and set end of downrod into mounting collar so the hole in the downrod lines up with the hole in the side of the mounting collar. 4.
INSTALLING THE FAN HANG THE FAN 1. Lift ball/downrod/fan into hanger bracket opening. NOTE: The tab opposite hanger bracket opening should fit in slot on ball. 2. Make wire connections, (refer to section titled “Electrical Connections”). 3. Slide canopy up and fasten to hanger bracket with 4 screws provided. WARNING: To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling.
ELECTRICAL CONNECTIONS ELECTRICAL CONNECTIONS: * Be sure electricity is turned off at the main power box before wiring 1. Four wires are connected to the fan. Black – this is the “hot” power to run fan. White – this is the “common” power to run fan and light. Blue – this is the “hot” power for uplight and light kit. Green – ground wire (on bracket or downrod). 2. If fan and light are to be connected to the same circuit, black and blue wires can both be connected to house circuit black wire.
BLADE ATTACHMENT BLADE ATTACHMENT: 1. Place fiber washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat this procedure without tightening the screw until all 3 screws have been started into the blade arm (Fig. 1). NOTE: Fans that have painted finishes may be packed with gaskets that can be used between the blade arm and blade to help prevent a clicking noise that may develop if blade screws loosen over time. 2. Tighten each screw starting with center screw.
INSTALLATION OF REMOVABLE SWITCH HOUSING NOTE: Be sure the power is off before installing. 1. Loosen the 3 side screws on switch housing hub halfway. 2. If installing light kit, carefully remove light kit plug in bottom of switch housing. Attach light kit to switch housing per instructions supplied with light kit. See “Electrical Connections” for hook-up of light kit. 3. Connect the plug and receptacle and make sure side buckle snaps in place. 4. Attach the switch housing to the switch housing hub.
OPERATION Turn on the power and check operation of the fan. The fan is controlled by the use of the fan speed pull chain as follows: one pull = high speed two pulls = medium speed three pulls = low speed four pulls = off For proper functions, ensure that the fan speed pull chain is pulled down fully and released each time. The uplight is turned on/off by the other pull chain coming from the switch housing. NOTE: Leave pull chain switch in “high speed” position when using optional wall control.
CARE AND CLEANING Periodic cleaning of your new ceiling fan is about the only maintenance that is needed. Only use a soft brush or lint free cloth to avoid scratching the finish. DO NOT use water when cleaning your ceiling fan. It could damage the motor or the wood blades and/or create the possibility of electrical shock. Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation.
