Specifications

POCKET WIZARD
ACCESSORIES
FLASHES & ACCESSORIES
297
ORDER & INFO. [phone] • FAX: [phone] [phone]
1-800-290-6750 • www.bhphotovideo.com
PHOTO - VIDEO - PRO AUDIO
WaveSensor
The WaveSensor is a sophisticated and easy to
use tool for capturing objects in motion. It uses
changes in sound or light to trigger electronic
flash units, cameras or both. The WaveSensor
has an internal microphone for sound triggering
and an internal light sensor, which works with
the remote laser included, or many other light
sources. The unit has an immediate trigger
output and a delayed trigger output linked to an
accurate timer for image placement after the
system is tripped. The controller has an output
disable circuit to prevent firing strobes or cameras during setup. A retrigger delay timer prevents
the system from firing again after the initial event. The WaveSensor can be used to measure the
timing of an event from start to finish, or calculate the "Lag Time" for a motorized camera so
the strobe fires when the camera has reached "full open". The WaveSensor is capable of triggering
from a single drop of water or a fast-paced auto race.
WS-1 WaveSensor
(803-205): Includes AC adapter, MM1 cable, two MMX cables, laser module,
lock-out switch, shock mount and AC adapter .........................................................................CALL
Low-Voltage Triggers
LVT-H Low Voltage Trigger -Household (WITLVHH):
Connects between the camera’s PC socket and the flash to prevent damage to the camera’s sync
circuitry due to high triggering voltage from electronic flash. Requires cables .......................77.95
LVT-M Low Voltage Trigger -Miniphone
(WITLVMP):
Connects between the camera’s PC socket and the flash to prevent damage to the camera’s sync
circuitry due to high triggering voltage from electronic flash. Requires cables .......................77.95
CM-N3-P
(WIPTCCE3):
For EOS-3, EOS-1v ...............................................142.85
CM-T3
(WIPTCCAFQ):
For EOS-1, EOS-1N, A2, A2E...............................104.50
N90M3-P
(WIPTCNF5):
For Nikon N90, N90S, F5, F100 ...........................197.95
RLM3-P
(WIPTCR6):
For Rollie 3000/6000 series...................................124.95
RZM3-P
(WIPTCMRZ):
For RZ-and 645 Pro-TL series..............................134.95
MAFM3-P
(WIPTCM645AF):
For Mamiya 645AF or 645AF-D ..........................134.95
NM3-P
(WIPTCNF3): For Nikon F4, F4S, FE, FM, F3, 8008........................................................................................96.95
Pre-Trigger Motor Drive Cables
Designed to keep the camera constantly “awake”, these cables have the same effect as holding the camera’s
trigger button pressed down half-way. A camera will trigger much faster in the “awake” mode, but will also
use up more battery power. However, the pre-trigger mode can be switched on or off from the cable itself.
Miniphone to Household Female (WIHHFMA)
For standard household sync cord ..........23.95
Miniphone to Sub-Mini Female (WISMFMA)
For Quantum motor drive cables ..............6.50
Straight 16˝ Trigger Button
to Miniphone Cable
(WITBM16)
To trigger transmitters..............................29.95
Adapters
Straight 3´ Trigger Button
to Miniphone Cable
(WITBM3)
To trigger transmitters ............................29.95
Miniphone Male to PC Female
(WIPCFMA)
For standard PC sync cord .....................14.95
Household to
PC Cord Adapter
(WIHHPCA)..................33.95
Mounting Bars
4˝ Isolation Mounting Bar (WIMB)
To mount PocketWizard products to
super clamps. For convenient place-
ment of PocketWizards and/or isola-
tion from RF (radio frequency) noise.
Includes velcro an 1/4-20 male
mounting screw...........................16.95
8˝ Isolation Mounting Bar (WIMB8FW)
To mount PocketWizard products to
super clamps. For convenient place-
ment of PocketWizards and/or isola-
tion from RF (radio frequency) noise.
Includes velcro an 1/4-20 male
mounting screw...........................18.95
4˝ Isolation Mounting Bar
8˝ Isolation Mounting Bar