User manual

ManualsBrandsREELY ManualsRC Model Aircraft AccessoriesFlying wing mixer (L x W x H) 31 x 8 x 8 mm

Connecting of the V-tail Unit/Delta Mixer

Connect the connection cable of the V-tail unit/Delta mixer (input B) soldered to the underside of the board

to the elevator output of the receiver.

For a V-tail Unit model, connect the connection cable soldered to the top side (input A) to the rudder output

of the receiver.

For a Delta model, connect the connection cable soldered to the top side (input A) to the aileron output

of the receiver.

Make sure you connect the two connection lines according to the correct polarity of the plug (see

operating instructions for the recipient or print on the receiver).

White cable: Control signal

Red cable: Operating Voltage Plus (+)

Black cable: Operating Voltage Minus (-)

Connect the two servos for the V-tail unit or the Delta model ailerons on the right-hand side of the V-tail

unit/Deltamixer.Payattentiontothecorrectpolarityoftheservoconnectingplugs.Thecontrolsignal(S)is

transmitted from the bottom of the three pin contacts (see picture).

Check the mixing function

Important:

 ThecorrectconnectionoftheV-tailUnit/DeltaMixerisverymuchdependentonthepositionof

the servos, as well as the mechanical construction of the rudder linkages. For this reason the

apswingsmustbecheckedaccordingtothecontrolcommandsofthetransmitterand,ifneces-

sary, the connection must be changed.

Whentheaileroncontrolleverissteeredintheupdirection,bothaps(bothelevatorattheV-tailmodelor

bothaileronsfortheDeltamodel)mustdeectupwards.

Ifoneapdeploysupwardsandtheotherdownwards,swapthetwowires(AandB)oftheV-tailUnit/Delta

Mixer on the receiver.

Shouldthetwoapsdeploytogether,butinthewrongdirection,swapthetwoservoconnectorsattheoutput

of the V-tail Unit/Delta Mixer.

Ifthesiderudderoraileroncontrolleveronthetransmitterisengaged,theapsmustdeployinopposite

directions. If not, the rotational direction of the servo does not correspond with the control direction on the

transmitter;activatethereversefunctiononthetransmitter.Therequiredcourseofactionistorefertothe

operating instructions of the remote control transmitter.

You can, of course, keep on using the transmitter functions such as the limitation (dual rate) or exponential

function on the V-tail Unit/Delta Mixer.

Disposal

 Theproductmustnotbedisposedofwiththehouseholdwaste.Disposeofanunserviceable

device in accordance with the relevant statutory regulations.

Technical Data

Input voltage ..................................................max. 5 .0 V/DC

Maximum servo current .................................3.0 A (<1 s: 8.0 A)

Mixing ratio ...................................................1:1

Resolution ......................................................200 increments

Receiver connection ......................................JR

Dimensions without cable L x W x H .............31 x 8 x 8 mm

Weight ...........................................................5 g

Operating Instructions

V-tail Unit/Delta Mixer for Model Aircraft

Item no. 1600321

Intended Use

Theproductisanelectronicmixermoduleusedtomixsignalsoftwooutputsofthereceiverandtoforward

thesetosignalstotwoconnectedservos.ThismakesitpossibletocontrolaV-tailoraDeltamodelplane

usingaremotecontroldevicewithoutabuilt-inmixer.Theproductissolelydesignedforuseinamodelplane

and the operating times associated with it.

Forsafetyandcompliancereasons,theproductmustnotbeconvertedand/ormodiedinanyway.Ifyou

use the product for other purposes than those described above, the product may be damaged. Furthermore,

improperusecancauseriskssuchasshort-circuits,re,etc.Pleasereadtheoperatinginstructionscarefully

and do not discard them. If you pass the product on to a third party, please include the operating instructions.

ThisproductcomplieswiththeapplicablenationalandEuropeanregulations.Allnamesofcompaniesand

Package Contents

• V-tail Unit/Delta Mixer

• Operating Instructions

Latest Operating Instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code

shown here. Follow the instructions on the website.

Explanation of symbols

An exclamation mark inside a triangle indicates important instructions in this operating manual

which must be adhered to.

 Thearrowsymbolindicatesspecictipsandadviceonoperation.

Safety Instructions

The warranty/guarantee will be void in the event of damage caused by non-compliance

with these safety instructions. We do not assume any liability for any resulting damage!

We shall not accept liability for damage to property or personal injury caused by incorrect

handling or non-compliance with the safety instructions! The warranty/guarantee will be

void in such cases.

• Unauthorisedconversionand/ormodicationoftheproductisnotallowedforsafetyandap-

proval reasons. Never disassemble the product; there are no components inside the housing

that you need to set or service. Besides, this will invalidate the warranty!

• Theproductisnotatoyandshouldbekeptoutofthereachofchildren!

• TheV-tailUnit/DeltaMixermustnotgetdamporwet.

• TheV-tailUnit/DeltaMixermaybeoperatedonlyinconjunctionwithmodelremotecontrol

systems.

• Themaximumpermissiblevoltageandcurrentvalues(seesection"TechnicalData")maynot

be exceeded, otherwise it will destroy the V-tail Unit/Delta-Mixer. Non-compliance with the

limits will void the guarantee/warranty.

• Only connect one servo to the V-tail Unit/Delta Mixer per output.

• Keep the biggest possible distance between V-tail Unit/Delta Mixer and plane control system

or motors for the installation, to avoid interaction.

• Install the servos cables connected to the V-tail Unit/ Delta Mixer so that no tension is created

andtheconnectorscandropduringtheightoftheV-tailUnit/DeltaMixer.

• Secure the connectors of the servos connected to the V-tail Unit/Delta Mixer with a strip of

adhesive tape.

• Fix the V-tail Unit/Delta Mixer to the model so that it is optimally protected against vibration,

heat, humidity or pollution.

• Handle the product with care; it can be damaged by impact, blows, or accidental dropping,

even from a low height.

• Do not leave the packaging material lying around carelessly, since it could become a danger-

ous toy for children.

Functioning of the V-tail Unit/Delta Mixer

Thecontrolsignal,whichisfedfromthereceiverviatheconnectioncable(inputA),solderedtothetop of

the circuit board to the V-tail Unit/Delta Mixer, passes this 1:1 on both servos connected to the output. As a

result, both servos turn in the same direction.

Thecontrolsignaltransmittedbythereceiverviatheline(inputB)totheV-tailunit/Deltamixer,placedon

the underside of the board,onlypassesthis1:1toaservo.Thesecondservoreceivesaninvertedreverse

signal so that both servos connected to the output turn in different directions.

Important:

For the V-tail Unit/Delta Mixer to work, both input connections (A and B) on the receiver must be

connected.

ThisisapublicationbyConradElectronicSE,Klaus-Conrad-Str.1,D-92240Hirschau(www.conrad.com).

Allrightsincludingtranslationreserved.Reproductionbyanymethod,e.g.photocopy,microlming,orthecapturein

electronicdataprocessingsystemsrequirethepriorwrittenapprovalbytheeditor.Reprinting,alsoinpart,isprohibited.

Thispublicationrepresentthetechnicalstatusatthetimeofprinting.