Product Manual

ManualsBrandsReelcraft Manuals3/8in. Retractable Air Hose ReelsSpring-Retractable Air Hose Reel — With 3/8in. x 50ft. Hose, 300 PSI, With Swivel Fitting and Inlet Hose

Operating Instructions

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725

Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605

Customer Service: 855-634-9109 • reelcraft@reelcraft.com • www.reelcraft.com

Series RT Spring Driven Hose Reels

Low Pressure Model Numbers:

RT402-OLP RT802-OLP RT625-OLP RT635-OLPSM

RT403-OLP RT803-OLP RT635-OLP RT650-OLPSM

RT405-OLP RT805-OLP RT650-OLP RT825-OLPSM

RT406-OLP RT425-OLP RT825-OLP RT835-OLPSM

RT602-OLP RT435-OLP RT835-OLP RT850-OLPSM

RT603-OLP RT450-OLP RT850-OLP

RT605-OLP RT465-OLP RT450-OLPSM

Dimensions

• Ensure that reel is properly installed before connecting input and

output hoses.

• Bleed fluid/gas pressure from system before servicing reel.

• Before connecting reel to supply line, ensure that pressure does

not exceed maximum working pressure rating of reel.

• Remember, even low pressure is very dangerous and can cause

personal injury or death.

• Be aware of machinery and personnel in work area.

• If a leak occurs in the hose or reel, remove system pressure

immediately.

• A high tension spring assembly is contained within the reel.

Exercise extreme caution.

• Pull hose from reel by grasping the hose itself, not the control

valve.

• Ensure that reel, hose, and equipment being serviced are

properly grounded. Use an ohmmeter to check ground

continuity.

• If reel ceases to unwind or rewind, remove system pressure

immediately. Do not pull or jerk on hose!

• Treat and respect the hose reel as any other piece of machinery,

observing all common safety practices.

SAFETY

Personal injury and/or equipment damage may result if proper safety

precautions are not observed.

Form# 1121-802A Rev: 7/2018

17 7/8”

16 1/2”

6”

2 1/4”

See

page 6

18”

16 7/16”

16 11/16”

3 5/16”

See

page 7

Summary of content (7 pages)

PAGE 1
Operating Instructions Series RT Spring Driven Hose Reels Low Pressure Model Numbers: RT402-OLP RT403-OLP RT405-OLP RT406-OLP RT602-OLP RT603-OLP RT605-OLP RT802-OLP RT803-OLP RT805-OLP RT425-OLP RT435-OLP RT450-OLP RT465-OLP RT625-OLP RT635-OLP RT650-OLP RT825-OLP RT835-OLP RT850-OLP RT450-OLPSM RT635-OLPSM RT650-OLPSM RT825-OLPSM RT835-OLPSM RT850-OLPSM Dimensions A 17 7/8” A B 16 1/2” B 16 7/16” C 6” C 16 11/16” D 2 1/4” D 3 5/16” E See page 6 E 18” See page 7 SAFETY Personal injury an
PAGE 2
Series RT Spring Driven Hose Reels Mounting the Hose Reel Prior to mounting the hose reel, ensure that the supply line pressure does not exceed the maximum working pressure of the hose reel. Do not exceed the maximum installation height of 16’ unless the reel was specified differently when ordering. The maximum operating temperature is 150 °F (66 °C). Unpack and inspect the reel for damage. Turn the spool by hand to check for a smooth operation. figure 1 Position the reel on the floor, wall or ceiling.
PAGE 3
Series RT Spring Driven Hose Reels Adjusting the Bumper Stop Pull out the hose until the latch pawl is engaged. The bumper stop may be adjusted by loosening the slotted screws shown in figure 6. Slide the bumper to the desired position and tighten the screws BEFORE PULLING HOSE to disengage the latch pawl. figure 6 Removing the Guide Arm Pull out hose until the latch pawl is engaged. Remove bumper by removing the slotted screws (figure 6). Disengage the latch pawl while maintaining a firm hold on spool.
PAGE 4
Series RT Spring Driven Hose Reels Replacing the Latch Pawl Remove the guide arm by following the procedure for “Removing the Guide Arm”. Remove the retaining nut as shown in figure 9. Replace the latch pawl assembly. Replace and tighten the retaining nut. Replace the guide arm and bumper stop by following the procedure for “Positioning the Guide Arm”. figure 9 Replacing the Hose To remove the hose Pull out the hose leaving 2 to 3 feet on the spool. Engage the latch pawl.
PAGE 5
Series RT Spring Driven Hose Reels Replacing the Spool Assembly Attach the reel securely to prevent it from moving. Pull out the hose just until the latch pawl is engaged. Remove the bumper stop by removing the slotted screws (figure 6). Disengage the latch pawl while maintaining a firm hold on the spool. Turn the spool hand over hand approximately two or three revolutions until the spring tension is removed. Unscrew the swivel stem from the main shaft.
PAGE 6
Series RT Spring Driven Hose Reels Item # Description # Req. 1 1/4-20 Lock Nut 2 3 Spool Assembly 1 4 U-Bolt 1 5 Latch Pawl Assembly 1 6 Guide Arm Assembly 1 7 Nut 1/2” 1 8 Bumper Stop 1 9 Hose Assembly 1 10 Nut 5/16” 4 11 Base Assembly 1 12 Spacing Washer 1 13 Snap Ring 1 14 Swivel Assembly 1 “E” Dimensions - See page 1 RT402-OLP RT403-OLP RT405-OLP RT406-OLP RT602-OLP RT603-OLP RT605-OLP RT802-OLP RT803-OLP RT805-OLP Item # Description # Req.
PAGE 7
Series RT Spring Driven Hose Reels Item # Description # Req.