Instruction Manual
11
10
8
9
7
4
3
10
6
2
5
2
5
4
3
1
11
3
5
12
3
5
11
3
NOTE:
-ALL THREADED BOLTS MUST THREAD PAST THE NYLON NUT BY AT LEAST 1 FULL THREAD,
BUT NOT MORE THAN 5 FULL THREADS. IF THE BOLT LENGTH DOES NOT MEET THIS
REQUIREMENT, SUBSITUTE WITH A LONGER OR SHORTER BOLT AS NEEDED. MAKE ANY
INVENTORY ADJUSTMENTS FOR THIS SUBSITUTION. ANY DEVIATIONS MUST BE APPROVED BY
THE RESPONSIBLE GOVERNMENT DOCUMENTATION ENGINEER.
EXP. NO.
WEIGHT
HEAT TREAT
FINISH
MATERIAL
UNLESS OTHERWISE NOTED:
DIMENSIONS ARE IN INCHES.
TOL.=ANGLES ±2° CONC. .010 T.I.R.
FRACTIONS REF. TO IND. STDS.
REMOVE BURRS, BREAK SHARP
CORNERS NOT TO EXCEED .015
MACH. SURFACES ARE
125 MAX
THIS MATERIAL IS OWNED BY
REELCRAFT INDUSTIRES INC. AND
IS NOT TO BE REPRODUCED OR
DISTRIBUTED WITHOUT WRITTEN
PERMISSION.
DRAWING TITLE
SIMILAR TO:
DRAWING NO.
DRAWING NO.
E.C.N.
DATEDESCRIPTION
LTR
SCALE
MFG. APPROVAL
ENG. APPROVAL
CHECKED BY
DRAWN BY
NOTED
NOTED
NONE
55 LBS
1:3 C
DWT
ELW
JLB 7/11/06
TYPE II ROLLER GUIDE
340307XX
340307XX
B1 REVISED AND REDRAWN
6/4/08
11273
A
C
D
E
F
G
H
I
J
K
L
B
A
C
D
E
F
G
H
I
J
K
L
2134568971011121315 1416
2134568971011121315 1416
R
340307
QTY.
1
4
10
4
10
2
2
2
2
8
4
2
340307A
NOTE: Components 1, 2, 6, 7, 8, 9 and 10 interchangeable between guide rollers 340307 and
340307A. The stainless replacement parts that differ on 340307A are described below.
10
4
10
4
2
DESCRIPTION
FRAME ASSEMBLY
ROLLER BRACKET
FLAT WASHER .375 ID
HEX CAP SCREW, 3/8-16 X 1 1/4”
NUT, NYLOK 3/8-16
HEX SHAFT
ROLLER ASSEMBLY
HEX SHAFT
ROLLER ASSEMBLY
HAIR PIN
HEX CAP SCREW, 3/8-16 X 1 3/4”
HEX CAP SCREW, 3/8-16 X 1 1/2”
FLAT WASHER .375 ID - 316 STAINLESS
HEX CAP SCREW, 3/8-16 X 1 1/4”-316 STAINLESS
NUT, NYLOK 3/8-16 - 316 STAINLESS
HEX CAP SCREW, 3/8-16 X 1 3/4” - 316 STAINLESS
HEX CAP SCREW, 3/8-16 X 1 1/2” - 316 STAINLESS
PART #
366001
366002
S110-6
S56-66
S81-6
326307-9
36606
326307-10
366007
C00680123
S56-68
S56-67
S357-6
S359-66
S355-6
S359-68
S359-67
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
3
4
5
11
12
APPENDIX “E”