Users Manual
A
dditional notes:
For A
ll d
evice
(15.21) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to
operate the equipment.
For mobile device
1. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device
and all persons. (Not including low power device (below 20mW))
2. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
For Class B digital device or peripheral or cordless phone (15.105)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
◆ Reorient or relocate the receiving antenna.
◆ Increase the separation between the equipment and receiver.
◆ Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
◆ Consult the dealer or an experienced radio/TV technician for help.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to
ensure that the proper spacing is maintained in the event the users places the device in their lap during use (i.e. positioning of antennas must be placed
in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use) and
2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter
testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements
require with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these
conditions can not be met (for example certain lapt configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the
antenna and users (for example access points, routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final end
product must be labeled in a visible area with the following: "Contains TX FCC ID: 2ARTO-N00-S1C
Un-license band: This device complies with Part 15 o
f
the FCC Rules.
Operation is subject to the following two conditions:
(1)this device maynot cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesiredoperation.
NCC警語
依據 低功率電波輻射性電機管理辦法:
第十二條
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。
前項合法通信,指依電信法規定作業之無線電通信。功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
本模組於取得認證後,將依規定於模組本體標示審驗合格標籤;
並要求平台廠商於平台上標示『本產品內含射頻模組: CCXXxxYYyyyZzW 』字樣。