HEZ2650F 848-A4M-93A0 (001) U S OWNER'S/OPERATOR'S MANUAL STICK EDGERS HEZ2650F WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. This spark ignition system complies with the Canadian standard ICES-002.
HEZ2650F SAFETY FIRST WARNING Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. 1. Read this stick edger Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury. 2.
HEZ2650F 1. Parts location 13 12 11 2 8 1 10 9 5 3 4 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. U S Loop handle Stop switch Throttle cable Throttle lever Blade guard Blade Wheel Spark arrester Starter knob Fuel tank Primer pump Choke lever Air cleaner cover 6 7 2. Specifications ■ HEZ2650F Overall size(LxWxH) ··············································································· 72.8 (1850)x11.0 (280)x12.0 (305) in (mm) Dry weight w/o acc.
HEZ2650F 3. Warning labels on the machine (1) (2) (3) (4) (5) (6) 15m (50ft) (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning! Danger of kickback. (4) Beware of thrown objects. (5) Warning/Attention (6) Keep all children, bystanders and helpers 15 meters away from the machine.
HEZ2650F 5. For safe operation WARNING • A brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operater or others. It is extremely important that you read and understand the contents of this Owner's manual. • Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories and parts.
HEZ2650F 5. For safe operation contain dangerous carbon monoxide. 10. Never to touch the spark plug or plug cord while the engine is in operation Doing so may result in being subjected to an electrical shock. 11.Never to touch the muffler, spark plug, other metallic parts of the engine or engine cover while the engine is in operation or immediately after shutting down the engine. These metallic parts and engine cover reach high temperatures during operation and doing so could result in serious burns. 12.
HEZ2650F 5. For safe operation ■ Transport 1. Drain the fuel from the fuel tank before transporting or storing the product. 2. When hand-carrying the product, cover over the cutting part, lift up the product and carry it paying attention to the blade. 3. Secure the unit carefully to prevent movement when it is transported. 4. A unit that receives a strong shock during transport and unloading may malfunction. ■ Fuel safety 1. Always use caution when handling fuel. It is highly flammable.
HEZ2650F 5. For safe operation lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product. 5. In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance. 6.
HEZ2650F 6. Set up SE1 (A) (B) ■ MOUNTING OTHER PARTS 1. Insert the driveshaft into the clutch drum, then attach the gearbox to the shaft tube as aligning the positioning holes and fasten the screw (A). Fasten the clamp bolt (B) firmly. (SE1) U S (A) Screw (B) Clamp bolt (B) Tightning Torque: 52~69in-lbs (6~8N.m.) SE2 2. Install the handle to the shaft tube and clamp at a position best for your job.
HEZ2650F 7. Fuel ■ FUEL lines or fuel tank of the engine. WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10 ft (3 m) away from the fueling point before starting the engine.
HEZ2650F 7. Fuel test standard has been discontinued by API in 1995 and it no longer exists. IMPORTANT • Gasoline/Oil mixture Storage Recommendations Store your gasoline or gasoline/oil mixture in a cool dry area in a tightly sealed approved container to limit the entry of moisture and additional air (oxygen). Moisture and air cause the development of varnish and gum, making the fuel stale. Stored gasoline and gasoline/oil mixture ages and loses its octane rating and volatility.
HEZ2650F 8. Operation ■ STARTING ENGINE The RedMax stick edgers are designed for edging lawn in gardens, parks, roadsides and so on. Before starting the engine, take the operating position and adjust the handle position and the wheel height as necessary. ■ ADJUSTING WHEEL HEIGHT 1. Loosen the wing nut and change the wheel height to obtain desired cutting depth. (OP1) OP1 (1) (3) (2) WARNING The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place.
HEZ2650F 8. Operation ■ HOW TO USE NOTE 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. ■ STOPPING ENGINE (OP4) 1. Release the throttle lever and run the engine for a half minute. 2. Shift the stop switch to the "STOP" position.
HEZ2650F 9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. WARNING • Always be sure to stop the engine before inspecting the stick edger for problems or performing maintenance. • Never alter the stick edger or take the engine apart. • When replacing parts, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax stick edger.
HEZ2650F 9. Maintenance ■ MUFFLER WARNING WARNING • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire.
HEZ2650F 9. Maintenance ■ BLADE (MA7) • Place the blade between holders (A) and (B) while locking the gear shaft by putting the bar, through the key holes on the holder(A) and the gearcase. Use the socket and the screwdriver to tighten the blade mounting bolt. MA7 MA8 (1) vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the machine.
HEZ2650F 10. Storage • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention. U S 11. Disposal • When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. 12. Troubleshooting guide Case 1.
HEZ2650F FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and RedMax are pleased to explain the emissions control system's warranty on your 2009 and later small off-road engine. In U.S.
HEZ2650F warranty is warranted for the remaining warranty period. Any warranted part that is scheduled only for regular inspection in the maintenance schedule will be warranted for a period of two years. A statement in such written instructions to the effect of "repair or replace as necessary" will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.
