BCZ3050S/SW/3060TS 115 35 75-10 (006) U S OWNER'S/OPERATOR'S MANUAL BRUSHCUTTERS BCZ3050S BCZ3060TS BCZ3050SW BCZ3050S BCZ3050SW BCZ3060TS WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. This spark ignition system complies with the Canadian standard ICES-002.
BCZ3050S/SW/3060TS SAFETY FIRST WARNING Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. 1. Read this brushcutter Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it.
BCZ3050S/SW/3060TS 1. Parts location BCZ3050SW BCZ3050S BCZ3060TS 15 14 3 3 13 10 2 12 17 5 4 1 2 4 5 11 16 6 6 8 9 9 7 8 U S 18 7 7 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Loop handle Suspention point Stop switch Throttle cable Throttle trigger Shaft tube Cutting attachment guard Cutting line head Gear case Spark arrester Starter knob Fuel tank Primer Choke lever Air cleaner cover Handle Hip pad Metal blade 2.
BCZ3050S/SW/3060TS 3. Warning labels on the machine (1) (2) (3) (4) (5) (6) 15m (50ft) (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning! Danger of kickback. (4) Beware of thrown objects.
BCZ3050S/SW/3060TS 5. For safe operation WARNING • A brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operater or others. It is extremely important that you read and understand the contents of this Owner's manual. • Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories and parts.
BCZ3050S/SW/3060TS 5. For safe operation contain dangerous carbon monoxide. 10. Never to touch the spark plug or plug cord while the engine is in operation Doing so may result in being subjected to an electrical shock. 11.Never to touch the muffler, spark plug, other metallic parts of the engine or engine cover while the engine is in operation or immediately after shutting down the engine.
BCZ3050S/SW/3060TS 5. For safe operation equipment, CLEAN UP! ■ Transport 1. Drain the fuel from the fuel tank before transporting or storing the product. 2. When hand-carrying the product, cover over the cutting part, lift up the product and carry it paying attention to the blade. 3. Secure the unit carefully to prevent movement when it is transported. 4. A unit that receives a strong shock during transport and unloading may malfunction. ■ Fuel safety 1. Always use caution when handling fuel.
BCZ3050S/SW/3060TS 5. For safe operation muffler, and the ignition wiring. 4. When replacing the any other part, or any lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product. 5. In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance. 6.
BCZ3050S/SW/3060TS 6. Set up IMPORTANT SE4 Tighten the screws gradually by turns. ■ INSTALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. (SE1) SE1 ■ INSTALLING LINE HEAD (SE4) 1. While locking the gear shaft, by inserting the supplied tool into the upper holder on the gear box, loosen and remove the hexagon nut(lefthanded) 2. Fit the line head assembly to the gear shaft over the holders. Hand-tighten it securely.
BCZ3050S/SW/3060TS 7. Fuel ■ FUEL lines or fuel tank of the engine. WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10 feet (3 m) away from the fueling point before starting the engine.
BCZ3050S/SW/3060TS 7. Fuel test standard has been discontinued by API in 1995 and it no longer exists. IMPORTANT • Gasoline/Oil mixture Storage Recommendations Store your gasoline or gasoline/oil mixture in a cool dry area in a tightly sealed approved container to limit the entry of moisture and additional air (oxygen). Moisture and air cause the development of varnish and gum, making the fuel stale. Stored gasoline and gasoline/oil mixture ages and loses its octane rating and volatility.
BCZ3050S/SW/3060TS 8. Operation ■ STARTING ENGINE 6. Move the choke lever downward to open the choke. And restart engine. (OP2) 7. Allow the engine to warm up for several minutes before starting operation. WARNING The cutting head will start rotating upon the engine starts. NOTE 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. OP1 1.
BCZ3050S/SW/3060TS 8. Operation ■ CUTTING WORK (LINE HEAD USAGE) WARNING 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2. Keep the cutting attachment guard in place at all times when the unit is operated. U S TRIMMING GRASS AND WEEDS • Always remember that the TIP of the line does cutting.
BCZ3050S/SW/3060TS 9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. ENGINE ■ MAINTENANCE CHART system/compornent procedure fuel leaks, fuel spillage fuel tank, air filter, fuel filter wipe out inspect/clean see ■ADJUSTING IDLING SPEED (p.
BCZ3050S/SW/3060TS 9. Maintenance ■ MUFFLER WARNING WARNING • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire.
BCZ3050S/SW/3060TS 9. Maintenance 10. Storage that this in turn could cause the engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste before use. • Check the intake air cooling vent and the area around the cylinder cooling fins after every 25 hours of use for blockage, and remove any waste which has attached itself to the brushcutter.
BCZ3050S/SW/3060TS 12. Optional blade usage WARNING WARNING • For security reason, in case of mounting the blade on this product and use it, purchase the blade kit (966 42 40-01) and change guard, handle from the original ones, and use shoulder strap. (OPT1 – OPT4) OPT1 Blade Kit : 966 42 40-01 • When sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury.
BCZ3050S/SW/3060TS 12. Optional blade usage ■ STARTING THE ENGINE Please refer 5.For safe operation (P.6), 8.Operation (P.12). • Make sure that the blade is not bent, warped, cracked, broken or damaged. • If you find any error to the blade, discard it and change new one which is certified by RedMax. WARNING OPT8 OPT9 • The product is equipped with a centrifugal clutch mechanism, so the cutting attachment could rotate as soon as the engine is started.
BCZ3050S/SW/3060TS 12. Optional blade usage areas of dense growth. d. Keep the blade sharp. A dull blade increase the chance of blade thrust. e. Avoid feeding the blade too rapidly. The blade can bounce away from material being cut if the blade is fed faster than its cutting capability. f. Cut only from your right to your left. g. Keep your path of advance clear of material that has been cut and other debris. ■ MAINTENANCE BLADE • Check the blade and the fasteners for looseness, cracking, or bending.
BCZ3050S/SW/3060TS 13. Troubleshooting guide Case 1. Starting failure CHECK fuel tank ➞ PROBABLE CAUSES incorrect fuel ➞ ACTION drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) spark plug ➞ spark plug is fouled/wet ➞ clean/dry ➞ plug gap is incorrect ➞ correct (GAP: 0.9 – 1.0 mm) ➞ disconnected ➞ retighten ➞ ACTION drain it and with correct fuel Case 2.
BCZ3050S/SW/3060TS FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS U S The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and RedMax are pleased to explain the emissions control system's warranty on your 2009 and later small off-road engine. In U.S.
BCZ3050S/SW/3060TS warranty is warranted for the remaining warranty period. Any warranted part that is scheduled only for regular inspection in the maintenance schedule will be warranted for a period of two years. A statement in such written instructions to the effect of "repair or replace as necessary" will not reduce the period of warranty coverage. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.
