40V LITHIUM-ION CORDLESS LINE TRIMMER Model: E312D Operations Manual www.redbacktool.com support@redbacktool.
TABLE OF CONTENTS the contacts – Explosion and fire • Contents…………..……………1 hazard! • Symbols. ….…………………1-6 • Specifications……..……....…...7 • Assembly & Operation…….8-15 • Major Trimmer Parts……...…16 • Exploded Parts List .….....17-19 Before using the tool, read the operating manual. Read all safety warnings and all instructions including the currently valid site rules and regulations for the prevention of accidents.
User unit will exclude the manufacturer from This garden tool is not intended for any liability for resulting injury and/or use by persons (including children) damage. with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or Preparation instruction concerning use of the 1. Familiarize yourself with the unit machine by a person responsible for and its functions as well as its their safety. controls. 2.
During Operation 12. When interrupting work, never 1. Do not switch on the unit if there are leave the unit unattended and keep it in persons (particularly children) or a safe place. animals in the immediate vicinity. 2. Ensure that children do not play with For The Battery Charger the unit. 1. Do not place any objects on the 3. Interrupt working if you notice that battery charger and do not place the persons (particularly children) or pets battery charger on soft surfaces. are nearby. 2.
power tool or battery-operated 3. Do not expose power tools (cordless) power tool. to rain or wet conditions. Water entering a power tool will Work Area Safety increase the risk of electric shock. 1. Keep work area clean and well lit. Cluttered or dark areas invite Personal Safety accidents. 1. Stay alert, watch what you are 2. Do not operate power tools in doing and use common sense when explosive atmospheres, such as in operating a power tool.
on. A wrench or a key left attached to 3. Disconnect the plug from the power a rotating part of the power tool may source and/or the battery pack from increase the risk of injury. the power tool before making any 5. Do not overreach. Keep proper adjustments, changing accessories, footing and balance at all times. This or before storing the power tool. Such enables better control of the power preventive safety measure reduces tool in unexpected situations. the risk of starting the power tool 6.
those intended could result in a Have your power tool serviced by a hazardous situation. qualified repair professional using only the identical replacement parts. Battery Tool Use And Care This will ensure that the safety of the 1. Recharge only with the charger power tool is maintained. specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 2.
PRODUCT SPECIFICATIONS Tool Model Rated Voltage No Load Speed Motor Type Cutting head Cutting Line Cutting Width Pole Diameter Handle Type Line Trimmer E312D 40V DC 7500 RPM Brush Bump feed 1.6mm Nylon 12” 25mm Loop Guaranteed sound power level Battery (Lithium-Ion) 96 dB(A) Battery Charger Weight Tool Warranty EP20 (2.0Ah) EP40 (4.0Ah) EP60 (6.0Ah) EC20 (2.0A) EC50 (5.0A) 6.8 lbs (3.
ASSEMBLY & OPERATION Warning! Remove the battery Wheel Assembly Installation pack before cleaning or maintaining The edger wheels are needed for the tool, fitting the edger wheel or edge trimming, and although they plant guard or before making any are not needed for normal adjustments to the tool, especially trimming, they can be left fitted to around the string head. the machine during normal Remove the battery pack before trimming operations. transporting or storing the tool.
Fitting the plant guard the battery is securely locked into The plant guard is used to prevent To remove the battery press and your trimmer from cutting your hold the latch on the rear of the plants. The wire plant guard is battery pack and slide the battery inserted into the holes provided in away from the trimmer. place the front of the head. The plant guard can be folded up when not in use, or easily removed Rewinding the spool The spool is supplied with the line pre-wound.
(0.065”) in diameter maximum 12m Then put the spool and spring into long (you may find it easier to the housing leaving the ends of the practice with a shorter line length at line protruding from the cutouts on first). Find the center of the line and each side. loop it onto the notch in the center Thread the string guides onto the flange of the spool. Wind the line line as shown around the spool, in the direction Slide into place.
OPERATION BEFORE OPERATING THIS TOOL, ENSURE THAT THE GUARD IS FITTED TO THE HEAD OF THE MACHINE. NEVER USE THE MACHINE WITHOUT THE GUARD Starting/Stopping the trimmer: To switch the trimmer on, press and hold the safety switch (1) and then pull the trigger switch (2) on the handle. Adjusting the line length – Bump feed To switch the trimmer off, release head the trigger switch.
Height adjustable push handle The auxiliary handle (5) is height adjustable. To move the handle, first release the orange handle clamp on the underside of the Setting the handle handle. Slide the handle to the length desired height and clamp in position Turn the lock sleeve towards the ‘unlock’ symbol about half a turn. Slide the lower part of the trimmer up or down to the desired length. Lock it in position by turning the lock sleeve towards the ‘lock’ symbol.
Maintenance, A storage, and disposal 1. Disconnect the machine from the battery pack before carrying out maintenance or cleaning work. 2. When not in use store the machine out of the reach of children. 3. Use only manufacturer B recommended replacement To use the trimmer in edging mode, parts and accessories. slide the orange locking knob on the 4.
5. 6. 7. 8. Inspect and maintain the injury, only use the charger to machine regularly. Have the recharge Redback 40V battery machine repaired only by an packs. Never try to recharge authorized technician. non-rechargeable batteries. The battery must be WARNING: If the charger is removed from the appliance plugged in and no LED lights are before it is scrapped. illuminated, unplug and check The appliance must be with your nearest authorized disconnected from the service center.
- The LED will flash green while the battery is charging - Once the battery is fully charged, the LED indicator will show a steady green light. - Remove the battery by pressing and holding the latch button and sliding out of the charger Lithium-Ion batteries have no memory effect – a partial charge will not damage your battery Storage of the charger and battery For long-term storage, it is preferable that the battery is fully charged and stored in a dry place at a temperature between 10 -25 ° C.
MAJOR TRIMMER PARTS 1. Battery 2. Safety switch 3. Trigger switch 4. Trimmer shaft 5. Auxiliary handle 6. Lock sleeve and edging function button 7. Angle adjustment button 8. Edger wheel 9. Guard 10. Plant protector 11.
EXPLODED VIEW AND PARTS LIST No. Part No. 1 20910110 2 20910100 3 20910090 4 60390180 5 20470050 6 71080090 7 20910120 Description Locking block Body cover Pipe sleeve Adjustment spring Rotate switch aluminum pipe Clip QTY No. Part No.
Tapping 8 60170730 9 20910080 10 20910080 11 71080100 12 20910050 Locking plate 13 20910060 Rubber box 14 20910130 15 60070110 16 20910040 17 20340140 18 20910020 19 60250210 20 20910030 21 60170670 22 21060130 23 EP40 24 21060110 screw Left adjust body right adjust body aluminum pipe Lock rubber Tapping screw auxiliary handle Foam tube Aluminum pipe bushing cylindrical pin Handle bracket Self-tapping screw Right handle assembly 40 60070120 1 41 20430160 1 42
25 30010240 Male tab 4 57 60350130 Flat key 1 26 20800020 Plug in seat 1 58 70030660 Output shaft 1 27 20470030 1 59 70670330 28 60380380 1 60 60240230 29 20470040 1 61 20150070 30 30080030 1 62 60170070 31 60390170 1 63 60070120 32 20530090 1 64 20880400 Wheel 2 65 20640220 Wheel hub 1 Self-lock switch Self-lock spring Start switch Micro switch Start spring Right button Gear wheel Spring washer Upper cover of gear box Self-tapping screw Self-tapping
