User Manual

C
A
FIGURE A
Main Unit
Remote
Head
Vehicle
Ground
Trailer
Socket
Main
Unit
Vehicle
Grommet
Hole
A
C
E
FIGURE B
4
7
2
3
5
6
1
4
7
2
3
5
6
1
150mm
X
1 2
3 4
L
F
Red/White
Red
Red/White
L
• Remove cover of Trailer socket to
expose wiring.
• Remove BLUE wire from trailer socket
and insert BLUE wire from Rear
Harness into Pin 5.
• Locate RED wire and cut 150mm from
base of socket.
Remove cut RED wire from socket Pin
6 and discard.
• Crimp and solder the Butt Splice (F)
to join the cut RED wire to the
RED/WHITE wire on Rear Harness (C).
Cover with heatshrink (L) and heat to
seal over joint.
• Insert RED wire from Rear Harness (C)
into Pin 6 on the trailer socket.
Existing Vehicle Grommet
Or New Grommet Hole
A
• Disconnect the battery negative
terminal.
• Connect the Power Harness (A) ring
terminal to the battery positive
terminal.
• Route the harness towards selected
grommet location (Refer Figure A).
Secure to existing vehicle wiring
where possible.
• Route the Rear Harness (C) and
Power Harness (A) into the cabin
through the grommet, ensuring a
good seal (Refer Figure A).
Note: If the battery is inside the vehicle,
route the Power Cable directly to the
Tow-Pro Main Unit location.
• Locate a suitable position in the kick
panel or glove box area to mount
the Tow-Pro Main Unit near a vehicle
Earth Point. Clean the area with
supplied Cleaning Pad (I). Secure the
Tow-Pro Main Unit to the vehicle using
supplied double-sided tape (H), and
cable ties (G) as necessary.
• Insert RED, BLUE & BLACK wires into
the Tow-Pro connector (D) as per
table above ensuring each terminal
locks into place with an audible
click. Snap off the secondary lock
and fit to underside of connector.
• Secure WHITE wire ring terminal to
vehicle earth point.
• Connect the Tow-Pro connector
(D) and the CAT 5 Cable (E) to the
Main Unit.
Rear View of
Connector
(Wire Entry Side)
4 3 2 1
Wire Colour
Terminal
1
2
3
4
Red
Blue
White
Black
D
Outside the vehicle, run the Rear
Harness (C) from the grommet
location to the Trailer Socket
following existing vehicle wiring
where possible. Secure with supplied
cable ties.
Note: Rear harness can be trimmed at
the trailer socket end if too long. Do not
trim before completing routing to trailer
socket.
Important
Avoid areas around fuel or
brake lines and any moving
parts.
Before commencing work, examine
vehicle for suitable cabin entry point for
all wiring - preferably using an
existing vehicle grommet in front of
passenger or to passengers left-hand
floor space.
If no suitable vehicle grommet is found,
you must drill a 25mm hole in the floor
adjacent to the left hand sill and use the
supplied grommet. In this case, move the
seat and lift the carpet and check
above and below for any wiring or areas
to avoid. Drill 25mm hole, de-burr and
protect against rust.
Important
Make a note of all Radio
settings (Confirm Security
Code if applicable).
• Find a suitable location on the
dash or gearshift surround to install
the Remote Head, ensuring clear
space to any moving parts or wiring.
Note: If your vehicle has unused switch
locations, check the REDARC website for
availability of a suitable Tow-Pro Switch
Insert.
• Route the CAT 5 cable (E) from the
Main Unit to the Remote Head
location (Refer Figure B).
• Use the supplied template to drill the
two 4mm pilot holes and then 25mm
hole.
• Insert the Remote Head into the
switch fascia (from behind) and
secure the nut using a 12mm
socket. Rotate the shaft fully
anti-clockwise and fit the knob with
“0” upwards.
• Feed the CAT 5 cable through the
hole and connect to the rear of
Remote Head (ensuring positive
lock). Press the assembly into the hole
securely. Secure the CAT 5 cable with
cable ties as required.
B
E
C
Important
Vehicle images are shown
only as a generic guide and
may differ from the installing
vehicle. Always refer to the
vehicle’s workshop manual
when removing vehicle
components
Important
Ensure the grommet is re-
sealed properly after harness
installation. Use silicon
sealant or similar if required.
H
Important
Check scale before using
template.
Ø4mm
Ø25mm
50mm
50mm
Ø4mm
Red