Reverse Park Assist Kit Part No: 546363XX11 Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Tow-Pro Wiring Kit Fitting Instructions Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Accessory Kit Estimated Fitting Time: 120 Minutes FI11928 Page 01 of 15 © 2018 Issue: 3 Date: 14/08/2018
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 General Notes • Read through the fitting instructions before installation of the accessory. Install the accessory following the fitting instructions. Failure to do so may cause damage to the vehicle or the accessory. • Ensure all recyclable discarded vehicle accessory components are packaging are recycled following local recycling regulations. • It is always recommended that this accessory is fitted by a qualified automotive technician.
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Wiring Diagram FI11928 Page 03 of 15 © 2018 Issue: 3 Date: 14/08/2018
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 1 Always refer to the vehicle’s Workshop Manual when removing vehicle components. Note down all clock and radio settings. • In the engine bay, disconnect the negative battery terminal. Step 2 • Inside the vehicle, remove the glove box (1). 1 Step 3 • Remove the five screws (1) on the glove box surround (2). • Remove the glove box surround (2).
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 4 • Remove the passenger scuff plate (1). Repeat for RHS. 1 Step 5 • Dislodge the door seal (1) and remove the passenger side inner kick panel trim (2). 1 Repeat for RHS. 2 Step 6 • Dislodge the drivers side lower trim (1) by first removing the two bolts (2) holding the bonnet release (3).
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 7 • From behind the drivers side lower trim (1) disconnect all the connectors (2). 3 • Dislodge the cable tie clip (3) and remove the drivers side lower trim (1). 1 2 2 2 Step 8 • Remove the cupholder assembly (1) from the center console by pulling in an upwards direction. 2 • Dislodge the blank switch panel (2) from the cupholder assembly (1).
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 10 • Fit the remote head (1) to the blank switch panel (2). 2 • Secure the remote head (1) to the blank switch panel (2) as shown. Torque the nut (3) to 0.8 Nm. • Rotate the shaft (4) full anti-clockwise and fit the knob (5) to the shaft (4) with “0" pointing upwards as shown below. • Refit the blanck switch panel (2) to the cupholder assembly (6).
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 13 • Slide the Brake Controller ECU Assembly (1) over the two studs. • Secure the Brake Controller ECU Assembly (1) on the upper threaded stud using the supplied M8 Flat Washer (2) and M8 Nut (3). 2 3 Ensure the grommet (4) is seated correctly. 1 4 Step 14 • In the passenger side foot well, pull back the floor carpet (1) to expose the insulation foam. 1 Step 15 • On the LHS firewall, remove the factory grommet (1).
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 16 • Cut an incision into the insulation foam (1) that is behind the previously removed grommet. 1 1 Step 17 • Remove the battery positive terminal cover (1). • Fasten the positive ring terminal (2) from the Electric Brake Harness to the positive battery terminal. 4 • Refit the battery positive terminal cover (1). • Fasten the negative terminal (3) from the Electric Brake Harness to the vehicle ground point (4).
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 19 • Inside the vehicle, route the Electric Brake Harness (1) from the passenger footwell to the driver’s side kick panel area. • Secure the Electric Brake Harness (1) to the existing vehicle harness using the supplied Cable Ties. Ensure the Electric Brake Harness (1) is routed in a way as to avoid any sharp areas. Be sure to avoid contact with the vehicle steering column and pedals.
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 22 • Route the Cat 5 Cable (1) along the dash towards the center console area. • Continue routing the Cat 5 Cable (1) under the centre console and out the cup holder cavity. Use a guide wire if necessary. 1 • Secure the Cat 5 Cable (1), using the supplied Cable Ties, to the existing vehicle harnesses where available. • Plug the Cat 5 Cable (1) into the remote head (2) and refit the cupholder assembly.
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 24 • Route the Electric Brake Harness (1) along the top of the chassis rail towards the rear of the vehicle. • Secure the Electric Brake Harness at every 300mm using the supplied 900mm Cable Ties (2). Note : Ensure Cable Ties are behind the fuel lines (3). 1 2 2 Step 25 • At the rear of the vehicle, route the Electric Brake Harness (1) along the chassis rail towards the LHS tail light area. 1 • Secure using the supplied Cable Ties.
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Step 27 • Locate the ‘Blue’ wire that is taped back on the trailer wiring harness near the 8-way connector. 1 2 3 4 • Locate the ‘Blue’ wire that is taped back on the Electric Brake Harness. • Cut the brass ferrule off and strip the insulation back 10mm on both the ‘Blue’ wires. • Slide the supplied Heatshrink over the wires before crimping both wires using the supplied Butt Splice with an indent type crimpers.
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 FI11928 15 © 2018 Issue: 3 Date: 14/08/2018
Suitable for: Nissan Navara NP300 Kit Part No: TPWKIT-008 Template 50mm 50mm Important Always confirm the length of the 50mm scale marker before cutting out the templates. Ø3.
