Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Tow-Pro Wiring Kit Fitting Instructions Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Accessory Kit Estimated Fitting Time: 120 Minutes FI11848 Page 01 of 13 © 2018 Issue: 4 Date: 14/08/2018
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 General Notes • Read through the fitting instructions before installation of the accessory. Install the accessory following the fitting instructions. Failure to do so may cause damage to the vehicle or the accessory. • Ensure all recyclables, discarded vehicle accessory components and packaging are recycled following local recycling regulations. • It is always recommended that this accessory is fitted by a qualified automotive Technician.
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Wiring Diagram FI11848 Page 03 of 13 © 2018 Issue: 4 Date: 14/08/2018
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 1 Important 1 Always refer to the vehicle’s Workshop Manual when removing vehicle components. • Note down all clock and radio settings. • In the engine bay, disconnect the negative battery terminal (1). • If vehicle has a dual battery kit installed, disconnect the negative battery terminals on both batteries. Step 2 • Remove the driver’s scuff plate (1) from the vehicle.
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 4 • Remove the driver’s kick panel (1) from the vehicle by removing the screw (2). 2 1 Step 5 • Remove the RHS trim cover (1) on the center console. 1 Step 6 • Remove the bolt (1) and the trim clip (2).
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 7 • Dislodge the RHS center console trim (1) and disconnect the Engine start button (2) from behind. 3 • Remove the RHS center console trim (1). • Remove the LHS garnish (3). 2 1 Step 8 • Remove the RHS garnish (1) above the lower cluster finisher (2). • Release the two bolts (3) and dislodge the lower cluster finisher (2). 1 • Disconnect all applicable connectors behind the switch panel (4).
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 10 • Fasten the Fuse Holder positive ring terminal on the Electric Brake Harness (1) to the positive battery terminal. • Secure the Fuse Holder (2) to the vehicle battery harness using the supplied Cable Ties (3). Important Ensure the vehicle positive battery terminal cover is seated fully and correctly after installation.
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 13 • Locate the RHS firewall grommet. Cut an access point (1) on the outer side of the RHS grommet. Lubricate the grommet access point (1) with a suitable lubrication if required. • Secure the section of the Electric Brake Harness (2) with four terminals to a guide wire using tape. Keep the thickness of the taped section small. Feed the guide wire into the previously cut RHS access point of the firewall grommet.
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 16 • On the RHS of the steering column, secure the Brake Controller bracket assembly (1) to the existing vehicle bolt (2) as shown. • Adhere the supplied Anti-Abrasion Tape (3) to the top of the bracket assembly (1) to prevent damage to any vehicle wires. 3 1 1 2 Step 17 • Connect the 4-Way connector (1) from the Electric Brake Harness to the Brake Controller ECU (2). 1 • Connect the supplied Cat 5 Cable (3) to the Brake Controller ECU (2).
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 19 • In the engine bay, route the Electric Brake Harness (1) (BLUE, RED & RED/WHITE wires) down to the RHS chassis rail. Note: the harness joint should sit approximately 100mm forward of the grommet. Important Ensure to keep the Electric Brake Harness (1) away from any suspension components, moving parts, exhaust pipes or sharp objects.
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 Step 22 • Locate ‘RED’ wire (pin 6) (1) on the trailer wiring harness socket head. 150mm • Cut the wire 150mm from the base of the socket. Pin No.
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 E. & O.E. This document is copyright and must not be used except as permitted below or under the Copyright Act 1968. You may reproduce and publish this document in whole or in part for your or your organisation's own personal or internal compliance, educational or noncommercial purposes. You must not alter or amend this document in any way.
Suitable for: Landcruiser LC200 Kit Part No: TPWKIT-005 FI11848 13 © 2018 Issue: 4 Date: 14/08/2018
