Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Tow-Pro Wiring Kit Fitting Instructions Suitable for: Toyota Hilux / Fortuner Kit Part No: TPWKIT-004 Accessory Kit Estimated Fitting Time: 90 Minutes FI11807 Page 01 of 11 © 2018 Issue: 5 Date: 13/08/2018
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 General Notes • Read through the fitting instructions before installation of the accessory. Install the accessory following the fitting instructions. Failure to do so may cause damage to the vehicle or the accessory. • Ensure all recyclables, discarded vehicle accessory components and packaging are recycled following local recycling regulations. • It is always recommended that this accessory is fitted by a qualified automotive Technician.
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Wiring Diagram FI11807 Page 03 of 11 © 2018 Issue: 5 Date: 13/08/2018
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Step 1 Important Always refer to the vehicle’s Workshop Manual when removing vehicle components. 1 • Note down all clock and radio settings. • In the engine bay, disconnect the negative battery terminal (1). Step 2 • Unclip the glove box dampener (1). • Remove LH retaining clip (2) by rotating anti-clockwise. • Remove the glove box (3). • Remove the passenger’s lower dash garnish (4).
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Step 4 • In the passenger side footwell area, remove the white plastic cap (1). • Using a large screwdriver, dislodge the carpet (2). 1 2 Step 5 • In the engine bay on the passenger side, remove the smaller grommet (1). • Insert a sharp object through the hole to pierce the firewall insulation. Note: If required, inside the cabin use a knife to enlarge the in hole in the firewall insulation.
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Step 7 • Continue routing the Electric Brake Harness (1) across the centre console and towards the driver side lower dash area. • Secure the harness (1) to the vehicle using supplied cable ties every 300mm. 1 Step 8 • Inside the vehicle, using the table below, house the terminals (1) from the Electric Brake Harness into the supplied 4-Way Connector (2), ensuring the terminals lock into the housing.
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Step 10 • Connect the 4-Way connector (1) from the Electric Brake Harness to the Brake Controller ECU (2). 3 • Connect the supplied cat-5 cable (3) to the Brake Controller ECU (2). 2 1 Step 11 • Underneath the RHS of the dash, secure the ground ring terminal (1) from the Electric Brake Harness to the vehicle earth point (2) using the existing fastener (3).
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Step 13 • Plug the cat-5 cable (1) into the remote head (2) . A 3 • Secure the remote head to the switch insert (3) as shown, (image A). Torque the nut (4)to 0.8 Nm. 1 • Rotate the shaft (5) fully anti-clockwise and fit the knob to the shaft (5) with “0" pointing upwards as shown (image B). 5 2 4 B 5 Step 14 • In the engine bay, secure the fused link ring terminal (1) to the positive battery terminal (2).
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Step 16 • Remove the ‘BLUE’ wire (1) from the trailer wiring harness socket head (2). • Tape back and isolate. 1 4 7 • Insert new ‘BLUE’ wire with brass ferrule from the Electric Brake Harness into the same position in the trailer socket. 2 Pin No.
Suitable for: Hilux / Fortuner Kit Part No: TPWKIT-004 Step 19 • Re-connect the negative battery terminal. • Test the operation of the Tow-Pro system as per the Tow-Pro user manual. • Dispose of any parts not used from the fitment. Important Secure all harnesses to the vehicle using cable ties. Refit all removed parts and secure all fasteners to the Service Manual torque specifications. Important Reprogram all radio stations and clock settings by referring to the vehicle's Owner's Manual.
